Having problems with your Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum ?

My Bissell cleanview is NOT suctioning well, all filters, nozzles, attachements, canisters and belts are clean and in good repair. We've pretty much made sure everything that I can get to without completely dismantling the vacuum is super clean and/or new... still poor suction


Answers :

Did u check the filter above the dirt cup?
\015\012
\015\012twist the yellow piece and wash the filter
Repair Help & Product Troubleshooting for Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bissell cleanview is NOT suctioning well, all filters, nozzles, attachements, canisters and belts are clean and in good repair. We've pretty much made sure everything that I can get to without completely dismantling the vacuum is super clean and/or new... still poor suction


Did u check the filter above the dirt cup?\015\012\015\012twist the yellow piece and wash the filter ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Hoover floormate Hi, I'm not sure what the model number is on my Hoover Floormate, but I can't get the cleaning liquid to dispense. The vacuum(dry pickup works fine). The handle squeezes without a problem. It used to work without a problem and then I didn't use it for awhile. When I came back to it, it wasn't working. Thanks, Alissa


The tank sits on what is called the reservior asm. it is actuated by the control rod inside the handle. With the tank off, watch and see if you can see that rod hitting the reservior asm when you squeeze the trigger. If it is moving up and down on ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr


Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Cleaning Filter Hi: I want to clean the filter on the B&D pet hepa vacuum, but can't figure out how to take it out of its housing. I can remove the housing from the actual vacuum, but don't know how to get the filter itself out. It sure does smell of dog, so any help would be appreciated.


... Black & Decker Black Decker Bagless Canister Pet VacVacuum

Recently purchase SC-N500 vacuum cleaner. Worked well only the first 2 times I used it to clean up plaster dust from floor after sanding. Since then it has not worked at all well wiht very poor suction. Fluff gets stuck in the hose and has to be manually removed. Suction power is very poor. I have washed the filter to remove the dust with no difference. Who do I contact in Brisbane to service or assess the problem further.


... Sanyo Vacuums

I own a Miele S5210 vacuum cleaner which has stopped working. It looks like the dust bag wasn't fitted properly and the machine is very dirty and the filters are completely clogged. I've cleaned it up as best I can and have replaced the filters but it still won't operate. How can I get inside the casing to clean the inner motor compartment? Thanks Tom


... Vacuums

I am having problems with the roller on my Oreck DTX-1300. It turns on and off intermittantly while I'm vacuuming. I have completly taken it apart and cleaned and inspected the roller unit.(I am very much mechanically inclined) This has stumped me, I have checked the electrical from the vacuum to the floor unit, and everything else that I could think of. Question: what does the metal sensore plate on the bottom of the roller unit do?? Anything anybody can tell me, I would greatly appreciate. Cap


... Oreck DutchTech DTX1300A Bagged Canister Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Cannister model#11627915701. connector terminals in extensionwand ,and wlre harness in hose handle get hot,,,look a bit singed.. can order and do ourselves. but would like a "tune up " ,cleaning of vacuum as well. purchased in 2008. have long haired dog,,,can't afford to be without it for very long. have sears store in clay ,ny. lady I spoke w/ says it would get sent out and take at least 2 weeks.!


... Kenmore Vacuums

I was lucky enough to get a Janome 372 very cheaply at a second-hand store but it came without the manual. A friend managed to thread it so that it works but the threading is completely counter-intuitive and I'm not sure that I'll be able to remember how to do it without a threading diagram to turn to in a pinch. Unfortunately, I can't seem to find a threading diagram online anywhere! Can anyone direct me to a site that shows this?


I would look in a site called www.Pronto.com/manualsI hope this is helpful to you . ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hover Elite Rewind I've only had this vacuum a few months and I really liked it until now. There is almost no suction from anywhere in the vacuum, and I've cleaned all the filters and rollers with my shop vac and made sure that everything was assembled correctly. It used to be really quiet now it is quite loud and it keeps over heating, and shutting off. At this point I have no idea what could cause this problem, the machine is nearly brand new and I can't afford a new one at this point.


You have to clean out the hose under the bottom of the vacuum cleaner. To do this you have to remove the bottom plate the covers the brush it has about 6 screws. Also remove the brush and belt in order to thourhly clean it. I had the same issue you h ... Vacuums

I had a manual, beung disabled, prop[le come over a help clean and put stuff away, but now the problem, is the vacuume won't stay put together and i can't find the damn manual, is it possible to get another it's a bissell power force model un sure of can i get anotrher manual. thomas d. silvia


BISSELL User's Guides can be downloaded at www.bissell.com\012On the front page under Customer Service click on User's Guides and enter the model number of your unit.\012User Guide will be displayed as a PDF file. ... Bissell 3522 PowerForce Bagged Upright Vacuum

I have to replace the power cord on my Bissell upright pet hair eraser vacuum because it is damaged from getting run over by the vacuum. Familiar story? Rather than pay a technician a lot of money, I feel I should be able to tackle this myself (went to college and everything). What are some pointers to help me bravely tackle this without the help of a male (no offense guys)?


Of course, its simple.\015\012Use electric tape to make sure the wires never touch, usually a phillips screwdriver will do to uncscrew the machine.\015\012just make sure you line up the cords the right way, positive to +ve and negative to ... Vacuums

Re. Proheat / Protech model No spray happens, I have made sure both the water bag is full & the cleaning fluid are both fully located, the water does seem to be getting into the carrier without having been sprayed.


Usually when it doesn't dispense water that means that the pump belt is worn. Here are the belts you need to replace and the manual:Biss ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Poor suction absolutely loved the machine when I first got it. I have dogs so it is getting a work out. however, the suction isn't as great as when I first got it. I have cleaned the washable filter and empty the cylinder after every vacuum. When I use the hose, the suction just isn't there. anything else I can do?


OK- I had the same problem and I took it to sears for service, It still wasn't great. So I proceeded to pull out all of the filters, including the internal filter that is not easy to get get to. I washed it and air dried it, put it all back together ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My vaccuum cleaner is an EVERSTAR 1200. I turned it on - everything appears OK until I realize that it is not suctionning. I cleaned out the canister - made sure the vacuum was not obstructed. Still no suction. What could it be?


First clean the filter on top of the canister, do not wet it, blow it and get all the accumulated dust out. Then check the hoses for obstruction. There should be an emergency valve on the rear part, if it is open, you better ck the hoses. ... Vacuums

With cleaning carpets with the Stowaway when the head gets a blockage it makes a high pitched whining sound and requires unblocking - then works fine. Now when vacuuming the head always makes the same sound when the head is against the carpet. you can also see that the rollers are slow or stopped. We have pulled the Stowaway virtually completely apart and checked for blockages as well as washed the filter and no difference. Any ideas?


... Dyson "Stowaway" Canister Vacuum Vacuum

Vacuum was just cleaned, filters everything, and still not getting good suction in upright postition. Is the beater bar adjustable?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK.


Sounds like a bad motor bearing. If it is, then you would have to replace it. Could be the brush roll, did you check the ends to make sure they turn easily? ... Vacuums

Our dirt devil bagless upright (110002) stopped working while vacuuming. we cleaned everything out and cannot get it to start again. the motor is warm, but does not smell hot. is there a reset switch/button we need to push? thanks, Carol


Hi, no im afraid its not that easy, the problem is with the wire that goes into the vac from the mains, now you see where the mains lead goes through in the back of the vac well what happens is when you vacing and moving the vac around this part wear ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Electrolux power nozzle, model 1692, power cuts on and off. I don't have the manual for it, but I'm trying to remove and clean the brush compartment. I removed the top, but not sure how to get to the brush. I would like to find a manual for it, because it's completely different than the one I use to have.


... Electrolux Vacuums

How do I clean the dirt from inside the vacuum cleaner, brand name panasonic mce6003. I bought it without the manual and I cant get the dirt out from inside it since it is bagless. Please help :-(


... Panasonic MC-UG371 PLATINUM LINE Bagged Upright Vacuum

I get a Rainbow vacuum E2 series , when I switch on it start after nearly 10 minutes . I cleaned up all the parts , I check everything but I don't find any damaged parts. Can someone help me . Tha


The problem could be either the switch or the controller. We have pickup service at your home for repair. Give us a call when you are able.RainVacwww.rainvac.com800-523- ... Rainbow E series Canister Wet/Dry Vacuum

Vacuum smells I have a 6 year old rainbow vacuum model E and it smells terrible everytime I use it. Probably because often times i don't remove the water basin after vacuuming and just let it sit. It's my own fault however now I don't know what to do to get rid of this terrible smell. I've water cleaned the hepa filter, not able to remove the separator screw to clean. Can you give me some suggestions?


In addition to vinegar, baking soda (sodium bicarbonate) is also an excellent remedy for many odour problems. Try generously sprinkling baking soda on a rug you wish to clean, and afterwards, vacuum up the spot. Rugs, and dirt ... Vacuums

Power Cord I have a Miele S528 vacuum and it has been acting up lately. I often times have to move the power cable around to get it to work. I am sure it is a loose connection inside the vacuum but I am not sure how to access the inside of the vacuum.


Hi There,Greetings,\012This definitely sound like a cord reel issue to me. This is really the \012only problem that I ever see on a Miele vacuum \012 \012 9 times out of 10 the cord reel needs to be changed. If you purchase\012 ... Miele Filtration Guard S528 Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1809 seconds