Having problems with your Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum ?

Bissell revolution roller won't turn

\015 I just replaced the belt, now the roller won't turn and it smells like burning rubber. Is the motor shot?\015

Answers :

These things are VERY sensitive to the roller being perfectly free of any haor or stuff. Clean the roller completely, put a new belt on, and make sure it is all turning perfectly before you plug it in...
Did you check the brush roll, if one of the ends is melted together and won't turn, then the belt will just slip and overheat.
Repair Help & Product Troubleshooting for Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roller wont turn on my bissell vaccum model 5770


... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

My Bissell Pro-Heat 2x 12 amps Model 9200-2 The rollers wont turn and the water wont release


WON'T SPRAY ??? ... Bissell 9200 Upright Vacuum

Bissell revolution roller won't turn


These things are VERY sensitive to the roller being perfectly free of any haor or stuff. Clean the roller completely, put a new belt on, and make sure it is all turning perfectly before you plug it in... ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

MY ROLLER WONT TURN - Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum


Did you check the belt? ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

My bissell proheat carpet cleaner wont turn on. Its plugged in and everything but wont turn on. I've had it for a few years but its always worked before. Do they have to heat up if I haven't used it in a while?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My dyson dc25 just turned off while i was using it first the roller brush stoped turning so i used the hose and now it turned off and wont turn on how do i fix it?


... Dyson DC25 All Floors Bagless Upright Vacuum

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.


Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum

My Bissell liftoff Revolution won't turn on. Is


Vacuums are not usually fused, but may have a circuit breaker--look for a small protruding button that when pressed, resets the breaker. The plug on the end of the cord may have a wire broken within the plug--replace it with one from a hardware or ho ... Bissell LiftOff Revolution Pet Vac 37602 Vacuum

Kenmore progressive direct drive roller wont turn


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Roller brush won't turn...the motor runs but wont turn..acts like it is seized up..


The belt may have come of or broke..\015\012Turn the vac over so the bottom is facing up..\015\012Remove the scews in the plate cover that surrunds the brush..\015\012Remove the plate cover..\015\012You will see if the belt is ... Vacuums

The Dyson roller ball vacuum I have is making me crazy because the roller bar wont turn. What gives?


Check that you dont have anything blocked in the roller, if all is clear there is a little red button on the side off the roller.\015\012Push this in and this will reset the roller...\015\012If that doesnt work, check that it is switched on with the ... Dyson Ball DC24 Bagless Upright Vacuum

Roller not turning, belt not working no water . The belt on my Bissell Proheat is not getting water (although there is plenty in the holding tank). It seems the belt is not turning and there fore the water is prevented from leaving the holding tank.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell 9400's brush rollers do not stop turning. When I was using the hose attachment for the stairs the handle was in the upright position and the brushes kept turning. Also water was leaking out of the rear right side onto the the carpet under the machine.


... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

I have a Bissell Upright Proheat 2x and the dual power brushes wont rotate. I went to replace the drive belt and noticed the drive shaft does not turn when power is turned on. What shall I check next?


Is there a light that comes on when you "turn the power on." If there is no light, and the unit is plugged in, how do you know there is current going to the motor? Sounds like there might be a break in the cord. Examine the cord near the plug end ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell wont turn on - Bissell 9400 ProHeat Upright Wet/Dry Vacuum


Hey, you may want to remove the upper handle to see if the wire harness is protruding, then reinstall making sure the handle is fully inserted onto the machine. If you continue to experience no power, you may want to have one of BISSELL's Aut ... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ


I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Bissel roller not turning - Bissell 3522 PowerForce Bagged Upright Vacuum


Hey, brush not turning can be quite frustrating. Here's a quick link to troubleshooting steps to assist you.\012\012http://www.bissell.co ... Bissell 3522 PowerForce Bagged Upright Vacuum

I just bought a bissell power roller prodry cleaner and turned it on and nothing happens. Is there another button I am not turning on to get it to work?


The power switch is on the back of the handle. If that dosen't turn the unit on take the handle off and put it back on make sure its tight. If still nothing then its defective. Bissell says not to return it to the store contact a service center. If y ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Brush bar wont turn, Bissell smells like burning rubber


The belt just goes from the motor shaft to the brush roll. Do the ends of the brush trun freely, or is one of them froze up, if so replace the brush roll. If it is ok, try to turn the brush roll by hand, maybe the belt got pinched and won't move. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Tried pressing in red button and switch next to on button to get roller working but not made any difference - still wont turn (any no suction)


Hi there,I'm sorry to hear you're having difficulty with your DC24. If you haven't been able to reset the brushbar using the reset switch on the cleaner head, I'd encourage you to get in touch with us directly so we can provide further assist ... Dyson Ball DC24 Bagless Upright Vacuum

Brush / roller wont turn


Most likely the belt is broken. Bad news regarding all Dyson's. You can't replace just the belt your self. You have to purchase a new belt assembly which includes the gears. And it wont be cheap. I would call it a design flaw but i am sure that ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Bissell pro heat 2x healthy home brushes wont turn


Hey Brenda! Here's a link to troubleshooting steps for the brushes not turning.\015\012http://www.bissell.com/FAQDetail.aspx?id=1128&cid=ccsocial ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0529 seconds