Having problems with your Bissell 3750 Lift Off Bagless Upright Vacuum ?
Replacing the belt
\015 Replacing the drive belt. The brush will not turn.\015
This link is for the manual it will give you full instructions on belt change
Repair Help & Product Troubleshooting for Bissell 3750 Lift Off Bagless Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.
On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum
I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum
Replace belt i need to replace the belt on an upright dirt devil 086310 vaccume but do not have a manual and can not find how to open the assy to replace the belt
On the bottom, there should be a few screws to remove to remove the plate covering the brush roll. However some may have screws on the top housing to remove the top. ... Vacuums
Belt replacement i am trying to replace the belt on my kirby g4 and i can not get the rooler off to replace the belt. if you could tell me how to do this it would be great.
Lift the light bulb housing up and you will find a latch that will rotate to release the front agitator housing and remove it from the machine. On the bottom of that housing, there are two latches that secure the bottom plate that covers the roller. ... Kirby G4 Bagged Upright Vacuum
The rotating sweeper on my Electrolux Discovery II isn't turning. Can I assume there is a belt that needs to be replaced? Also, how do I get at the sweeper unit to replace the belt? Finally, where can I find a replacement belt? Thanks!! Dewey
... Electrolux Vacuums
My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.
The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums
Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t
It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums
I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums
I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef
Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums
I replaced my Bissell vacuum cleaner belt with a Bissell belt. I ordered it from them so I know it's the right one. I replaced it and the roller won't spin and the belt smells like it burning.
Beckiande485: You will need to unplug the vacuum from the wall, lay it down so you can see the bottom of the vacuum head and remove the bottom plate (foot plate) Probably philllips head screws. pull up on the roller (called the beater bar). ... Bissell Vacuums
Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?
Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum
I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks
You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum
I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.
I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums
I have a 20 yr old upright U4689-910 with a broken agitator belt. I have a replacement belt. I have removed the L shaped plate on the bottom of the vac. It is not clear to me how to replace the belt at this point.
If it is like the older hoover models you need toDISCONNECT FROM MAINS FIRST then lift out the roller with the brushes on it, grip firmly at both ends and pull away from body of hoover, loop the belt over it and push it back in. Make sure you l ... Hoover Vacuums
Replace belt on fantom cyclone vacuum? the manual does not decribe replacing the roller belt - i can't get it open to expose the belt
On my 10-year-old model, the two screws securing the cover are under the two llight bulbs. Pry off the clear plastic covers, take out the bulbs and screws, and the cover lifts off. ... Fantom Vacums Cyclone XT Upright Vacuum
My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?
Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Hi, The belt of our Dirt devil bagless vaccum broke and we got new belt and replaced it. Even after replacing the belt, the brush is not rotating. Any suggestions please ?
Did you check to see that the beater brush, the brush that the belt drives, is free of debris and moves freely?\015\012When they bind up they can cause the belt to break.\015\012Remove the beater brush just as you do when changing the belt and clean ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike
... Hoover Vacuums
Belt replacement can you tell me how i replace the belt on my electrolux velocity hoover please
Need to know if it is a Electrolux or a Hoover and the model number. ... Vacuums
I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel
The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums
Where can you find a belt replacement for dyson dc17 animal and how do you replace the belt
Contact Dyson directly and they will ship you one for free but i would take you unit in because they changed the brush style due to a defect(would cause belt breaks often). They went from a thin belt to a thicker one so the brush is wider too and if ... Vacuums
My belt broke and I cannot find a replacement anywhere. Can you tell me where I can buy replacement Sweep n Groom belts for my central vacuum system.
You can get replacement Sweep n Groom belts here:\015\012\015\012Sweep n Groom Belts ... Vacuums
Replace the belt on a Eureka contour model 2900 upright vaccum. I just want to see a picture of the way it comes apart. It a almost new and just needs the belt replaced.
I have listed below a link to the owners manual for your model and a link where you can purchase the belt you need. Hope it helps you!Eureka Contour 2900 ... Vacuums
Replace Hoover Slider belt and reassemble. Online schematics too fuzzy and small to read. All parts fell out when trying to replace belt.
Here is a link to the belt you need and the manual, hope it helps.Hoover S2105 Slider Belt\015\012\015\012\011\011\011\011\011\011 ... Hoover S2105 Slider Bagless Stick Vacuum