Having problems with your Bissell 3750 Lift Off Bagless Upright Vacuum ?

The rotating brush at my new bissel vacuum doesn't work. The belt is OK, the canister is empty and clicked into position, no clog???

Answers :

Repair Help & Product Troubleshooting for Bissell 3750 Lift Off Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The rotating brush at my new bissel vacuum doesn't work. The belt is OK, the canister is empty and clicked into position, no clog???

... Bissell 3750 Lift Off Bagless Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.

Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?

Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Brush will not spin. filters are clean, no clogs, belt is fine. remove canister, it works fine plenty of suction.

Probably a good idea to remove the brush and clean as best you can.\015\012Add some WD40 at each end by the plastic clips and turn by hand until they move freely.\015\012Reassemble being sure the belt is on properly. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Brushes run freely on the cog and I put on 2 new belts and new brushes on my Bissell Proheatx2 the brushes do not turn when the machine is running even if I have the handle in the relesed position

I know how frustrating it can be when the brushes don't turn when you're ready to clean.Here's a quick link to troubleshooting steps to assist you:\015\012 ... Bissell Vacuums

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a

Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Replacing a belt on the Riccar 8850...I see how the brush assembly will work with the new belt. But I don't see how a new belt will turn on the small rod extending from the motor. Is there a pully missing?

There is not a pulley missing, when the belt is tight the shaft will turn the belt but when the belt loses elasticity it will slip on the shaft when being used on the carpet. Replace the n\012belt at least once or twice per year. ... Riccar 8850 Vacuum

Machine will not pump out water. Brushes work, motor works, new belt, Just will not put out any water??? It is a Bissell Powersteamer,Clearview 4 row brush , dirtlifter.

IF you take the tank out of the base you will see a recepticle where the tank nipple fits into the base. There is a cross looking pattern in the recepticle. Take a pointy object and press down inside the cross area between the bars in the little pie ... Vacuums

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.

Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

The belt on the beater brush is too loose and the brush won't turn, I have ordered new belts and it still doesn't work!!

Look in your manual for the proper routing of the belt, there may be piece broken and missing without you realizing it. If this not the case, there has to be some kind of adjustment on this unit. ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?

The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?

Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My vax rapide xl ultimate v-027y brushes not working..new belt fitted and same problem

Hello i have a vax rarid xl carpet cleaner when you switch power on just makes a buzzing noise can you help thanks ... VAX Appliances Vacuums

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?

Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

Canister powerhead brush does not seem to spin when the carpet level adjustment is on any level other than "high". Could it be something as simple as needing a new belt and is there a difference in a regular belt as opposed to "whisper belt"?

The belt is worn/stretched to the point that it cannot take the load on low level setting due to more resistance against the carpet and there is also no signifagant difference between the two belts except for expecting a longer belt life from the whi ... Kenmore 25512/ 25513 Progressive Canister Vacuum

How to repair BEAM Central Vacuum Power Brush. Motor works perfectly, belt brand new but unable to spin brush.

... Vacuums

Beater brushes don't work, what to do? They only work when the canister is in about an 85 degree up position.

This appears to be a loose connection. The below post was answered by highntools a while ago. It probably is related to you problem.\015\012\015\012I have finally fixed my sister's dyson dc 15 beater bar \015\012problem. It w ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile

... Eureka Smartvac 4870 Bagged Upright Vacuum

Bissell 8910e Aromapro. Jams when being pushed along floor. I think brushes drop down and cause problem. However brushes turn when machine is laid flat. Motor works. Doe it need new belt ?

Check your depth adjustment on your brushes ... Bissell Vacuums

I have a Eureka Contour model 2900 type A upright vacuum, the roller works fine nothing clogged, took it apart motor blade is free of debris, no suction from tube and blasts OUT air from the front HEPA filter location. New bag, New belt, nothing in hose.any clues as to why this can be happenning? Air should not be blasting out of the HEPA filter.

Even with your explanation,it seems the hose is clogged.Try taking the hose off,then blow through it or pour water through it.If this doesn't do it,make sure the suction canals are going to the proper areas. ... Eureka 2900A / 2901A Contour Bagged Upright Vacuum

I have a Bissell quicksteamer powerbrush steam cleaner. The power brush will not spin but the motor works to rotate it. I went to purchase a new belt but the guy told me the belt was fine? Any other suggestions?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Stopped working new item given as a gift, used once, in the middle of cleaning then died. Did as manual stated for over heating, empty canister, clean all filters and allow to cool for an hour. Left over night, tried the next day but does'nt work???? What can i do???

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1003 seconds