Having problems with your Bissell 3750 Lift Off Bagless Upright Vacuum ?
My bissell bagless hoover makes a louder noise and dust collects in upper chamber instead of the pull out part
Repair Help & Product Troubleshooting for Bissell 3750 Lift Off Bagless Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My bissell bagless hoover makes a louder noise and dust collects in upper chamber instead of the pull out part
... Bissell 3750 Lift Off Bagless Upright Vacuum
Dust collects on outside of canister on Hoover twin chamber bagless cleaner . I have replaced the filter & rubber gasket at bottom of the canister ,checked for blockage.
... Hoover Vacuums
No Suction I have a dc18 dyson and it had lost suction from the main hoover and the hose part. If you remove the dust collection part there is suction from the hole behind that part. I have cleaned all part to this hoover but the problem is still there. Any help would be apprieciated. Thanks
Filter removal step 1Turn power off and unplug the machine.\015\012\015\012To remove the washable filter: Rem ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan
I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
Hoover U5280-900 upright bagless vacuum twin chamber has a broken slider (switch) to go from tools to floor and carpet--what is the part called?? Indicator knob or cam activator?? where to order it??
... Hoover Windtunnel Supreme U5280-900 Upright Vacuum
I have a dyson dc07 bagless vacuum cleaner. How do I split the top and bottom halves of the dust collection bin? There is a lever and catch on the side, I have tried pulling and turning, but with no success.
Hi at the top of the Cyclone there is a lever underneath the Handle. The Handle I am referring to says Dyson on it. Firstly you must release the Cyclone from the spine. After doing this you will be left with the Cyclone and the Cyclone Bin all in a ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Cannot work out how to empty dust part (bagless model)
HiA visitor today knew what to do and has solved the problem thanks!Jenny ... Vacuums
My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga
I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums
Eureka Altima. Dust bin will not pull off for emptying. slide the lever sideways, and dust bin will not pull out. Has two tabs on the bottom. Appears may have the wrong part on this unit.
Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless
Get over it and buy a new one!!! ... Vacuums
My problem is that dust is shooting out of my powerforce bagless bissell. I pulled and detached the filters, hitting them againt my front steps which is cement, burshing my hand across the filter . Yes there was dust coming from it there. I continued to do this until no more dust is coming from it. When I cut it back on I'm still seeing dust depris coming from the vac.
... Bissell 6594 PowerForce Bagless Upright Vacuum
Dirt is collecting in the lower part of the vacuum and not collecting in the dust cup as it is supposed to causing the motor to heat up. Is it the seal?
Look for a clog in the hose ... ... Euro-Pro NV31 Infinity Vacuum
My FIL purchased an Electrolux bagless canister vacuum model EL5 76501 last year. When I tried to use it today, the hose keeps pulling out of the power brush whenever I pull it towards me. it doesn't seem like anything has broken off. The only thing I noticed was that the rubber ring washer seems to be flattened. Could it be something that simple or do you think some part has fallen off and gone missing? Regards, Craig Somersett
I believe I've just had the same problem and after searching for a small gray horsehoe clip that needs to first be found and then inserted into the slot for it on the tube section that comes out of the beater bar. Insert this clip from the outside af ... Electrolux Vacuums
I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil
Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums
I am trying to find out a part number for a rubber gasket that goes on the inside of a Hoover Windtunnel Cyclonic Platinum BAgless upright. It is a very thin, light-weight gasket made of rubber that helps seal the filtering tubes. If you know where I can find a parts break down, please advise,,, JON [email protected]
Hi There,\015\012\015\012I'm not sure exactly which part you are asking about, so I went ahead and uploaded the parts schematic of your vacuum cleaner, that will diagram all the parts, and part numbers.\015\012\015\012If you n ... Hoover UH70015 Bagless Upright Cyclonic Vacuum
I have a Hoover 6630-900 bagless upright. The "valve arm rear, part #38719048" broke. I have a repalcement part, but cannot get the spring, frontt and rear arms assembled correctly. Ant hints? Do you have a photo of the assembly on the vac? Thanks, Lee Duncan
... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne
... Hoover S3614 Vacuum
How to replace switch on a Hoover WindTunnel twin chamber bagless vacuum
... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Am i going mad? I've just brought an electrolux Cyclone Ultra 2000W hoover. I've got it out of the box and have tried to fix the cover to the unit (i.e the bag free area which collects the dust). It won't fit. I've tried everything and think it must be faulty. Has anyone ever come across this before? Grrrrrr.
Take it back to the store and compare it to another one, and possibly have a store manager help you, if they can't get it, then they should give you a different one and make sure that it will work before leaving ... Vacuums
Filter I bought this Hoover a few years ago-- just now about to use it first time. I cannot find my user's manual and don't know how to change the filter-- or to clean it or whatever I am supposed to do with it. Also, there is a handle on one side of the unit that seems to be attached to an empty chamber or canister kind of thing. It looks like it should pull out, but it does not budge. I really would like to have a manual, but can't seem to find one. Is there a similar model that is still
This is not for the exact same model, but should help you out:\015\012http://edge.maytag.com/epipubs/56511B47.PDF ... Hoover U8143-900 Upright Vacuum
Hoover steamvac spin brush puts out water, won't pull it back up. Checked all parts, no cracks. Cleaned filter.
Check for the front panel duct located on the lower tank front. this is the part you need to remove to attach the hose. also check to make sure the lid is on and secure on the lower tank. remove the lower tank and look on top of the motor cover towar ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hair gets stuck in upper filter basket instead of going into the lower basket that you are supposed to empty. It is a Bissell 37604 Lift-Off Revolution Pet Bagless Upright Vacuum Cleaner
Check both filters. If one or other is increasingly dirty, wash or clean it out. Also check the air waves leading to the bagless bin canister part. If one air way is blocked the remaining dirt will try and access the bin other way due to the natural ... Vacuums
I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?
Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?
... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
I have a hoover windtunnel bagless vac that is several years old. the floor vacuum part still works fine, but the handtool attachment has no suction and is useless all of a sudden.
Don't have your model number, but some have a valve down on the noozle part that may be broke. When it is its upright position, the valve won't change over to the hose only position. You would have to remove the top cover to see this. ... Vacuums