Having problems with your Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum ?

Bissel 3670-2 brush -roller dose not rotate at all even after I ttry to pull the belt. Could someone please explain the "mechnis or the principles how the brsu roller works?

Answers :

Repair Help & Product Troubleshooting for Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissel 3670-2 brush -roller dose not rotate at all even after I ttry to pull the belt. Could someone please explain the "mechnis or the principles how the brsu roller works?

... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Hi i have got a Dyson dco4 it switches on but the roller doesn't go round. I have checked the belt which has gone so I have no idea what else it could be please could you tell me what else it could be

If the belt is gone, then you need a new belt. Otherwise, ensure floor select switch is set to ON.\015\012\015\012If you don't have a user's manual, you can use the below site to get one free.\015\012 ... Dyson Vacuums

I have Hoover whisper Cyclonic. I just opend beacuse it was showing Clogged. I removed all dirt etc from the belt and now roller are not moving round and the smell of burning is coming due to rubber not moving on the roller. I looked at the manual which tells me in cased on roller being Jamed if need to use the stich to reset. I looked all over could not find the switch. Can you guys help me please.

... Hoover Sh40080 Zen Whisper Bagless Multi-Cyclonic Canister Vacuum

Have model UH70085 and went to hoover.com and they had no replacement for the very thin belt that turns the roller I brought the belt number stamped on it to home depot and they could not help. Can you? Please advise.

See if you can find a generic brand. Had the same problem with mine but found one at kmart that worked. Or try finding it on the internet. ... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Havent used for about two years. I had to put the belt on it. It doesnt seem to be sucking up very well and after about 15 minutes of vaccuuming the bag was empty. My house got really dusty. I know the rollers were spinning because i looked. I could hear some dirt going in but could definatly tell it wasnt working properly. Is it in reverse or something?

After two years you need to make sure the bag is connected properly and inspect it for tears and that the hoses are connected correctly and not deteriorated. Make sure the hose is clear. You should be able to feel the suction at the end of the hose. ... Vacuums

Hello, I have a Riccar 8000. The belt works, the bar spins, and it will **** things up. However, it will not pick up threads and dog hair or anything from the carpeting. Mu husband took the bottom off and there were a couple of small parts on the plate. We have no idea where they belong. Could not see them in the photos in the manual. Could it possibly need a new roller? Any help would be most welcome. Thank you! Mary Simon

... Riccar Vacuums

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?

Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum


Look on youtube for fixing a kirby belt. ... Kirby Ultimate G Bagged Upright Vacuum

I have an older Oreck XL that has worked great. The belt recently broke and I reinstalled a new one but now there's a rattling noise like something is loose and a burning smell. I've cleaned it as well as I could but still nothing. Help please!

When you turn it on, is the brush roll spinning? (Check carefully, as lifting the unit from the floor exposes a brushroll that should be spinning at a high RPM.)\015\012\015\012Did you get the brush roll properly seated in the slots? Does ... Oreck XL Ultra Bagged Upright Vacuum

Noise Hi... I was doing normal house work and had been using it on carpet... I put it on floor for my hardwood floors and picked up loose clean cat litter and went to put it back on carpet and it made a horrible noise like it was rubbing. cleaned the filter... cleaned the roller thingi ...checked the belt and it is still making that horrible noise. It does not make the noise when I have it on floor but as soon as I put it on carpet it screams at me. Help! Please and thanks Linda

Hi Linda,\015\012Sounds like clutch problems, try to move the lever for carpet/floor back and forth a few times maybe it will free up. If it still makes the grinding noise, the clutch assembly will have to be replaced. Let me know, i can even ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Could someone please advise how to remove the cover on a Vax Power Pet 2. I'm trying to change the belt, have removed the screws from the sole plate but the cover seems to be held in place by the

Go here > http://support.vax.co.uk/power-2-upright and download the manual with full instructions ... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I have a Eureka The Boss Mini (Model # 442) vacuum cleaner. It is not working properly sometimes Today I did a cleaned the roller brush thoroughly and powered it on to see if it spins at all. It spins only in Carpet model, but stops sometimes. Please can you tell me what could be the problem?

... Electrolux Vacuums

Im trying to replace the belt in my widepath tempo. Once I put it in the roller.... I don't see what it should attach to, to work and stay in place. ?? Please guide me.

... Hoover Vacuums

Belt keeps sliding over on the roller bar and rubbing on plastic parts. Belt is a "U" belt and I am told it should be a "R" belt. Sears sold me a "U" so I will try and find the R tomorrow. What keeps the belt other than tension from sliding onn the roller bar? Could it be that just the wrong belt could cause this??

The 4870 Series uses Part number 61110. It is a "R" Belt. It will appear too be to large. This is normal. ... Eureka Smartvac 4870 Bagged Upright Vacuum

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.

Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.

Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.

Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430

Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony

... Kenmore Vacuums

I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......[email protected]

You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum

When I turn the vaccuum on the roller works for about 20 seconds, then I hear an awful, loud noise, and the roller does not work. Sounds like maybe some gears are being stripped? Please help

It sounds like you need to change the belts. You can get replacements and view the manual here:Dyson DC07 Belts and Manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a

Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!

There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel

The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0931 seconds