Having problems with your Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum ?

Brush will not spin. filters are clean, no clogs, belt is fine. remove canister, it works fine plenty of suction.


Answers :

Probably a good idea to remove the brush and clean as best you can.\015\012Add some WD40 at each end by the plastic clips and turn by hand until they move freely.\015\012Reassemble being sure the belt is on properly.
Repair Help & Product Troubleshooting for Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brush will not spin. filters are clean, no clogs, belt is fine. remove canister, it works fine plenty of suction.


Probably a good idea to remove the brush and clean as best you can.\015\012Add some WD40 at each end by the plastic clips and turn by hand until they move freely.\015\012Reassemble being sure the belt is on properly. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

My Kenmore canister model (116) 26212601 works in hard-surface mode (basic suction), but the brush won't spin for carpets, and when I try to turn it on, it makes a whiny sound and then turns off as it does when I need to press the overload button. I looked inside a bit, and the belt isn't broken--it seems fine. So not sure what the problem is. Thanks for any help.


... Kenmore 27815 Bagged Canister Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?


Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.


Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

Have ultra vision and have changed filter and foam filter, checked all hoses but still will not pick up. Belt is fine and brush is clean and spinning properly. dirt stays at top of filter instead of falling into canister.


My kids get mine stuck all the time :(Take the vacuum outside then:Remove the hose at the bottom and see if there is any obstructions. Also shake the hose to make sure there is nothing in there as well or take it out side and make s ... Dirt Devil Vacuums

No suction for rugs but the hose works fine. Removed the canister and suction is at that point


Hello,\015\012\015\012Remove the base plate and beater bar. Clean the suction cavity behind the beater bar. That's where they almost always plug up.\015\012\015\012--W.D-- ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho


Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

I have a Eureka Contour model 2900 type A upright vacuum, the roller works fine nothing clogged, took it apart motor blade is free of debris, no suction from tube and blasts OUT air from the front HEPA filter location. New bag, New belt, nothing in hose.any clues as to why this can be happenning? Air should not be blasting out of the HEPA filter.


Even with your explanation,it seems the hose is clogged.Try taking the hose off,then blow through it or pour water through it.If this doesn't do it,make sure the suction canals are going to the proper areas. ... Eureka 2900A / 2901A Contour Bagged Upright Vacuum

Suction All belts are working, the hoses are not pluged. I don't have any suction at all. Could it be the filter in the canister where the dirt goes?


Absolutely all the air in a vacuum would pass through the filter and if its clogged badly you could loose all your suction and if the belt is more than a year old then replace it even if it isnt broken ( they stretch out over time ) ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!


Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue

I have removed a clog from the hose and cleaned the air filter. But I have no suction. If i remove the filter the is plenty of suction.


Get a new filter ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Recently purchase SC-N500 vacuum cleaner. Worked well only the first 2 times I used it to clean up plaster dust from floor after sanding. Since then it has not worked at all well wiht very poor suction. Fluff gets stuck in the hose and has to be manually removed. Suction power is very poor. I have washed the filter to remove the dust with no difference. Who do I contact in Brisbane to service or assess the problem further.


... Sanyo Vacuums

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.


Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

Luv300b vacuum brushes won't spin. The belt is fine but still not working. Any suggestions?


... LG Electronics Kompressor Plus Upright Vacuum Cleaner LUV300B

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!


Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Low suction The beater bar still spins fine, but the suction seems low. I have cleaned all of the filters, but it is still too low to spin a lot of the attachments.


Hi Megan,I'm sorry to hear you're having difficulties with your DC17. If it doesn't seem to be picking up as well as usual, you may have a blockage somewhere in the machine. To check for this, please follow the steps shown in our online suppo ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu


Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1432 seconds