Having problems with your Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum ?

Bissel home healthy vac. The brush only turns on for a split second and shuts off. Each time I put it in the upright position and start over, it does the same thing. I thought it may be the switch up on the handle. I replaced it, no luck.

Answers :

Here is some information about a second Auto Cut-Off Switch near the power switch:
\015\012About the only "gripe" I can come up with has to do with the automatic brush shut off mechanism that causes the brush to stop rotating when the unit is moved into an upright position. This one's a double edged sword though. On one hand, it's very nice, because when you move from vacuuming to dusting, the automatic shutoff ensures that you're not going to be roughing up the carpet in one place while the vacuum is stationary. On the flip side, it can be a negative in isolated situations when you're vacuuming in a narrow space, such as the landing on my stairs. In these tighter areas, your natural tendency is to pull the handle upright as you pull back towards the wall, which shuts off the brush mechanism. The unit doesn't have to be perfectly vertical to shut off the brush, it seems to engage at about the twenty degree point. Again, this is somewhat of a moot point, because there are obvious advantages to having this design incorporated into the vacuum. There is a separate brush shut off switch near the power switch, but how often would people forget to turn off the brush when dusting? I'm already training myself to keep the handle at lower level while vacuuming and not bringing it near the angle that engages the shutoff, so this "problem" will probably correct itself with time anyway.
\015\012It sounds like a cut-off switch is your problem. It has to be located hear the swivel head of the vacuum, I would think, in order to trigger it. Upon reading reviews, I got the impression that Bissel's customer support would be of little help, but you could try to contact them. Personally, since you sound like you're mechanically inclined, I would take it by a Vacuum Repair Shop and just ask them what they think. 9 time out of 10 they'll know pretty much what the problem is, and if you can get them to tell you where the cut-off switch is, you'll probably be able to fix it yourself. Otherwise, they may offer to fix it reasonably (we hope).
\015\012A lot of problems with switches involve dirt. If you can locate the switch, you might be able to just spray some electrical contact cleaner in it, and get it working again.
\015\012Hope this helps, and good luck. Thanks for using FixYa!
There is no other clog. I even pulled the cover off of the brush. I wanted to make sure there was nothing clogged in the brush area. I pulled the brush cover. Nothing clogged. I checked connections on micro switch also. Still does the same thing. Filter that slides out in front. \015\012Clean. The heppa filter is clean.
Repair Help & Product Troubleshooting for Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissel home healthy vac. The brush only turns on for a split second and shuts off. Each time I put it in the upright position and start over, it does the same thing. I thought it may be the switch up on the handle. I replaced it, no luck.

Here is some information about a second Auto Cut-Off Switch near the power switch:\015\012About the only "gripe" I can come up with has to do with the automatic brush shut off mechanism that causes the brush to stop rotating when the unit is mo ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Panasonic NN-SD776S microwave Start button stopped working. I know, the first thought is a bad door switch because "everyone knows a microwave should not turn on if the door is open." I am experienced with electronics, but even the timer won't start at all. Funny thing is, I had this exact model do this exact thing just over 2 years ago - troubleshot all the hardware until I was lost, finally bought a new one from Costco (June 4/08). And now 2 years later this one craps out - a 2 year timer

Hello Aaron,Since your microwave is controlled by logic, and the start button / timer portion is not working, I would start troubleshooting the power supply.Get a look at the integrated circuits that are on the circuit board, ... Vacuums

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.

Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

I had to replace the handle. The wiring is inside the handle. I would like to verify the position of all the switches and the location of a spring that fell out.

Dear Heidimtaylor,\015\012\015\012For this first we will required your model no. I will advised you too visit the following site and search for your model's service manual. It contains details which you required. Following link will help you... ... Vacuums

My dyson slim vacuum doesn't switch from hose to floor mode. I thought the foot lever was broken. I realigned it but it doesn't switch now from floor mode to hose mode. I take out the hose and I can see the white part. I thought it should move as you go from upright to recline position of the handle.

The changeover valve is not activating - call the Dyson helpline - they'll set you up for a repair with a repair dealer in your area. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Brush won't spin when position of handle changes

The belt for this machine is very specific and only one size fits. It is not uncommon for vac shops to sell the wrong belt because the proper belt is not available from normal supply houses, so they will substitute something they think will work. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My vacuum starts but stops immidiately I replaced on/off switch & belt but it didn't help me its still doing the same thing. Please help me out

It could be the power source .e.g. The lead or plug with a broken wire making intermittent contact. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

No power unable to manually turn off power, i opened up rear handle hatch to inspect the mechanism/linkage. The red on/off button seems locked in the on position. I replaced the hatch and now i have no power at all. what happened? Is there a fuse?

This vacuum has a recall notice on it. It has to do with the switch. You might want to check... They will fix it for free ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug

... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Dyson animal loses suction when I let the handle down from the upright position to use, I've cleaned the foam filter, and the plastic filter holder and dried thoroughly, removed and cleared the right side U-bend, and the center, rear U-bend access, also made sure nothing was in the way of the beater bar. Any thoughts? thanks. lorri

Is the noise a loud screaming or a grinding/vibration? The screaming is an air flow problem and you'll want to check your hoses are clear and all the seals are tight. The grinding is an issue with the roller/belt/clutch/motor/housing. From what I'm r ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

After a brief power outage my Marantec 4700 garage door opener has problems opening/closing. When opening it stops at the fully open position and the lights blink, when closing it automatically reverses just as it fully closes and then the lights start to blink again. I checked for obstructions and tried to reset the limits of travel per the manual, it still does the same thing. Any ideas on what to try next?

This is not a sensor issue, I have a similar problem, sensors work fine, garage door is still fully functional, all operations, including safety sensors work properly, just the overhead lights flash. I suspect there was damage to the power board due ... Vacuums

Kirby G5 vacuum.....machine started turning on and off depending on the position of the handle. Now it will not turn on at all----help anyone

Your cord is bad up on the handle where the swiveling strain relief. ... Kirby G5 Bagged Upright Vacuum

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?

Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum


Check your belt or maby something wraped around the end of the roller. ... Dyson Ball DC24 Bagless Upright Vacuum

I have a iRobot 4150 and have recently experiencing performance issues with the vacuum. Recently, it started stopping about a minute after you turn it on. I thought maybe the battery was the issue, but I bought a replacement. It has worked well for the past 6 months. While it's running it sounds like it is going to die, even though it is fully charged. Any ideas?

Yes, a common issue with the cleaning head module, chm. You will need to diassemble the Roomba and remove all debris from the CHM. Also take a look in its gear box. ... iRobot 4150 Roomba Vacuum

I just bought a foldaway hoover with wide path. I plugged it in and started to vacuum and dust flew everywhere. Walmart would not give me my money back so they gave me another hoover foldaway with the wide path. I thought this one might work. This one does the same thing. It blows dust out the sides and you can't vacuum with it. Any help would be great.

Your Vac probably does not have a filter installed inside the unit, that is why fine dust escapes through the vents. Remove the dirt canister/cup from the unit and you will see a filter frame behind. Possibly the filter itself is missing or wrongly i ... Hoover U5172900 Fold Away Widepath Bagless Upright Vacuum

When I replace the rubber on the cylinder and return the lever handle to it's original position in order to close it, the rubber comes off. How may I resolve this frustrating problem? thanks, bw

See if the clip that holds the belt is not bent make sure the belt is hooking on and getting hooked on to the engine shaft. ... Kirby Ultimate G Bagged Upright Vacuum

Can you remove the plastic hose that leads to the handle as mine has split. I thought i could remove it by pushing in the two black bits of plastic then shorten the hose. so far it wont budge. Is it meant to as Dyson sell the whole thing in one? cheers john

Yeah sorry it is sold as a complete unit and its a real pain to strip down so it better and faster to just buy the whole thing from dysons website  ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?

The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

I can't get my dirt devel cv 950 to start, have replaced fuse, tied the two wires together on the hose attachment door, no clicking or nothing when i plug in. are these things junk or what may be

... Dirt Devil CV950 Central System Vacuum

Err5 When charging the battery, it starts out flashing amber, but after several minutes it turns red and the err button flashes five times. The troubleshooting says to hold the buttons above and below the power button for ten seconds and this may resolve some software issues. I tried that but it goes back to the amber light then red again. I replaced the battery hoping that was the issue, but it still does the same thing.

... iRobot Roomba 530 Robotic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0671 seconds