Having problems with your Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum ?

Bissell 5770 brush motor won't run

\015 Suctions fine on the main motor. Motor on the brush won't engage. I'm suspecting the circuit board due to a few issues with the entire unit starting sometimes. Any way to check it?\015

Answers :

Repair Help & Product Troubleshooting for Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.


... Bissell Vacuums

DC 17 UPRIGHT BRUSH MOTOR WONT STAY RUNNING. TURN


Have a look at the filters first as it sounds like you blokeage ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The Brush Motor on my Bissell Healthyhome Vacuum wont start


I had this same problem. There is a screw that holds the top handle and the lower handle "together". If this screw is not TOTALLY tightly screwed in, this will cause the contacts in the switch to BREAK contact, and therefore one or BOTH motors may no ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Bissell 5770 brush motor won't run


... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles


Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Has a Bissell, Pro Heat 2X rug shampooer. It powers up & and the motor runs but the brushes are not rotating and water is not being dispensed.


Brush roller not working and water not dispensing was mostly caused by a brush belt being broken or is out of place.Turn the machine off and unplug it if the Brush roller do \015\012not turn. Remove any objects caught in the brush roll. A ... Vacuums

I have a bissell 1698 powersteamer. i have already cleaned heater and completely cleaned all parts , checked the mix piston, checked belt. it will not shoot water or mix. the motor runs, it will **** water and the brush turns. is it the pump and does the pump just shoot the soap?


Pump is probably bad. When you put the lid back down, did you put the piston on the bottom of the smart mix knob? Also the smart mix knob should be in the water only selection when the top is pushed all of the way down. Also sometimes the flow ind ... Vacuums

Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt


... Bissell 21K3 CleanView Helix Bagless Upright Vacuum

Roller brush won't turn...the motor runs but wont turn..acts like it is seized up..


The belt may have come of or broke..\015\012Turn the vac over so the bottom is facing up..\015\012Remove the scews in the plate cover that surrunds the brush..\015\012Remove the plate cover..\015\012You will see if the belt is ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Motor doesn't run I believe it the brush on the motor. two motor brushes one is completly gone about 1/8 inch left could this be the problem.the other motor brush still has 1/2 inch left. and current to motor tested good.


Sounds like your belt slipped off. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Brushes run freely on the cog and I put on 2 new belts and new brushes on my Bissell Proheatx2 the brushes do not turn when the machine is running even if I have the handle in the relesed position


I know how frustrating it can be when the brushes don't turn when you're ready to clean.Here's a quick link to troubleshooting steps to assist you:\015\012 ... Bissell Vacuums

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Bissell lift off motor wont turn on.


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.


I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Power head motor is good,runs great from test cord switch seems to work. brush roll cleaned but power head motor will not run


If you have checked the power delivery down to the powerhead and you have current running to the powerhead, then you likely have a burned fuse. There is a fuse built into the powerhead motor and is usually located on the field winding. This is not ea ... Eureka 6831A Bagged Canister Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell Powerwash Proheat. model 1698-j, 220-240v, 50/60Hz, 1200-1400w. Motor stopped suddenly (ident label specifies type Ametek 119464-02), supply inline fuse at motor ruptured, fuse replaced but motor sparks like an angle grinder at armature and blew replacement fuse. Where can I obtain a replacement carbon brush set for the motor. UK based


... Bissell Vacuums

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

Brush will not turn on on my Bissell Healthy home vacuum, the brush button is depressed and brush is clear. The vacuum motor works fine, just the brush will not turn on. Is there a part to replace?


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Panasonic power brush with dual edge cleaning 12 amps rottating brush doen't move..motor runs but brush not...how to get inside unit to fix it ... Thanks Robert


... Panasonic MC-V9638 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0675 seconds