Having problems with your Bissell 6594 PowerForce Bagless Upright Vacuum ?

I have recently replaced the belt and filters. The belt is in the correct position and the rotating brush moves freely. The motor is very loud. It still vacumns but I'm afraid the motor will burn up.


Answers :

Does it sound different than it did before you made the repairs to it or does it sound the same. Just so you know some of the upright vacuums on the market today sound like a jet airplane landing in your living room.Canister vacuums are generally quieter than uprights. The Filter Queen is a very quit machine and has been around fpr about 75 years.They are rather costly though.
If this helped you please don't forget to click the yes box on your way out....Have a good day and good luck
Repair Help & Product Troubleshooting for Bissell 6594 PowerForce Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have recently replaced the belt and filters. The belt is in the correct position and the rotating brush moves freely. The motor is very loud. It still vacumns but I'm afraid the motor will burn up.


Does it sound different than it did before you made the repairs to it or does it sound the same. Just so you know some of the upright vacuums on the market today sound like a jet airplane landing in your living room.Ca ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?


... Kenmore 34722 Grab-N-Go Upright Vacuum

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!


That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Burning Smell Hi, I have a Rainbow E series that when I run the vacuum there is a burning smell. I have cleaned the entire unit and filter but still have the smell? I am afraid that the motor will burn out?


Check the carbon motor brushes, there might be arcing on the armature. New brushes may help if the armature is ok. ... Rainbow E series Canister Wet/Dry Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?


If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Hoover f7452-900 Makes high pitched very loud whirring sound in motor. Smells of electrical burning. Still works fine but i'm afraid to use it.


... Hoover V1 SteamVac SpinScrub Vacuum

Hello can you help me please? I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well? Can you help please? Thankyou Martin


Some debris, even sand or dirt, probably got into the motor, causing damage to the armature. If this is the case, you will need to replace the motor. The burning smell from the motor is generally a sure sign of a bad motor. ... Kirby G4 Bagged Upright Vacuum

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?


Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

BURNING SMELL My DC 07 has suffered from poor suction in the upright position for some time now but this morning it ground to a halt. It was if the motor had burned out. I turned it upside down and some small stones etc tumbled out. I tried switching on again and the motor kicked in but the smell was horrendous so i switched off immediately. If it's likely to be **** inside the motor area i don't no how to access it. I've removed for fixing screws but still unable to prise apart. Is it just the


Hi.\015\012\015\012Try this site http://dysonmanuals.llc.nu/ has service manuals covering removing the Dc07 motor. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

The motor spins but the belt will not move, therefore the rubber on the belt burns right where it is attached to the motor.


Sounds like your carpet beater roller is jammed up, probably with hair or string, in most cleaners you can remove the roller by taking the cover off below the brush. Remove the roller and clean wrapped uo stuff ... Oreck XL Ultra Bagged Upright Vacuum

Vorwerk ET 340 - been great but now noticing strong burning smell after vacuuming some hair from the bathroom. Bag is nearly empty. Gave it a rest then unscrewed the cover housing the motor and all looks clean (dust is sucked up the pipe and doesn't appear to get near the motor). When I restarted it, burning smell still there. Are there any filters that might need changing? What could be causing the smell? Could the hair have gotten caught somewhere? Thanks.


Jessica,\015\012\015\012Try changing the dirt bag.\015\012Check if the motor gets hot after operation. You can come to check it by touching outside the motor housing. If it is hot or just warm.\015\012Is the smell of burning hair or something e ... Vacuums

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?


Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Bissell PowerForce Turbo: The motor spindle becomes very hot while spinning, causing the new belt to burn and break. Is this because the motor is overheating?


Something is preventing the brush roller from turning even though it seeems to be OK when not in contact with the floor. The motor shaft is spinning on one spot of the belt, causing the heating, the smell, and eventual belt failure. I have had brush ... Bissell 6594 PowerForce Bagless Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Hoover F6025900 Steam Vac Widepath LS, I own this steam vac and I found bits of rubber under the machine when I turned it on, smelled like burned rubber from a belt? Can you please tell me if there is a belt on this carpet cleaner and if so, how to access the belt? I have taken out some screws and still cant get to the belt? Thanks


Well there is no belt, and not sure what the rubber would be from, everything is plastic or metal. Unless it is really an electrical smell, which means the motor is going bad.\015\012\015\012 ... Hoover Vacuums

Ihave a Hoover Windtunnel self-propel model U6445-920. The belt from the drive motor to the big wheel will not run in the center of the wheel. The belt runs about 1/3 off the wheel. I have tried several new belts and still the same problem. What do I need to do to repair this problem.


The large wheel may be worn off center. If the belt stays on and is not thrown, you can run the vac. if there is wobble in the wheel causing a genuine belt to slide off replace the wheel mechanism. ... Vacuums

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Brushes not turning but motor still working belt


Belt might be stretched out.. Take it to a local authorized shop and get it looked at. ... Vacuums

Motor makes loud racket and smells like burning, but still works.


Bag? There is a paper filter and maybe a foam filter ... bag? Maybe this is a newer model that I am not familiar with. Anyway ... ...\015\012\015\012It sounds like your motor has been eating dust. Please check here for your repair: ... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

My Bissell 3760-1 has stopped sucking in the roller portion. The grab n go part are working fine. Checked the belt and it looks fine. Did I burn up the motor or a microchip?


Hey Lisa! Sorry you're having difficulty with your Lift-Off vacuum. Here's a link to troubleshooting steps to assist you with the suction.\015\012http: ... Vacuums

Burned smell hi, I have used my hoover 4 times and is starting to smell as something burned, I checked the troobleshouting part of the owner manual and it says that check the belt, I already did that and everything is ok I used the hoover again and still smelling bad and start to work very slow I better shut off it.. what could I do??


If the motor slowed down this would indicate a bad motor. not cost effective on this model to replace unless under warranty. it is not uncommon these days to see a motor go bad every now and then.\015\012\015\012What are the first 4 digit ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

My bissell aroma pro had a horrible burning smell then stoped sucking up water. the motor was still working and water was being feed out just not back up. the machine was hot as i had already cleaned 3 rooms in the house. i let it cool down but the burning prob returned as soon as i turned it back on. any help would be great thanks


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0896 seconds