Having problems with your Bissell 6594 PowerForce Bagless Upright Vacuum ?

My bissell 6596 motor running hot, therefore keep breaking belt, what should i do.


Answers :

Repair Help & Product Troubleshooting for Bissell 6594 PowerForce Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bissell 6596 motor running hot, therefore keep breaking belt, what should i do.


... Bissell 6594 PowerForce Bagless Upright Vacuum

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Bissell PowerForce Turbo: The motor spindle becomes very hot while spinning, causing the new belt to burn and break. Is this because the motor is overheating?


Something is preventing the brush roller from turning even though it seeems to be OK when not in contact with the floor. The motor shaft is spinning on one spot of the belt, causing the heating, the smell, and eventual belt failure. I have had brush ... Bissell 6594 PowerForce Bagless Upright Vacuum

Belt keeps breaking, but motor turns easily by hand on bissell powergroom, burnt rubber smell as well.....


Something is preventing the roller from spinning when in contact with the carpet. This causes the belt to stop turning and the motor shaft spinning in one spot causes the belt to burn and break. The protective guard could be damaged or not installed ... Bissell Powergroom Pet Vacuum

The belt on my Bissell Powergroom Dual Cyclone vacuum keeps getting hot and breaking. I have replaced it twice already. What can I do?


... Bissell 6594 PowerForce Bagless Upright Vacuum

I keep replacing the belt and keeps melting and breaks. what do i need to do? everything else is working, the little piece of metal that hooks on the belt gets too hot and melt the belt


I think your talking about the motor spindel,,(the little metal bit?) if the motor is that hot its going to burn out soon, check that the brush is free to turn if its tight free it off its full of grit or fluff also check that the motor turns freely ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.


I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

My bissell vacuum is very loud and the belt keeps breaking


... Bissell 6594 PowerForce Bagless Upright Vacuum

Belt keeps breaking on my bissell vacuum cleaner


... Bissell Vacuums

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.


... Bissell Vacuums

Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt


... Bissell 21K3 CleanView Helix Bagless Upright Vacuum

Bissell bagless motor shaft is too hot and melting belts


My guess is that the roller binds on the carpet (high pile?) and the motor shaft, glazed from use, spins without moving the belt and quickly burns a hote through it. I've had that experience! ... Bissell Vacuums

Vacuum Belt keep breaking


When your first belt burnt, the burnt plastics goes into the roller ends and then it dries off causing your roller to not turn or put more pressure on your belt. Until you clean that you will continue burning your belts soon after you put them in. Yo ... Dirt Devil Breeze Bagless VacuumVacuum

Bissell upright has weak suction and motor running hot but can't find a blockage


... Bissell 8975 CleanView Bagless Upright Vacuum

Belt keeps breaking on dirt devil 85335


Check and see if the brushroll still turns easy. if it doesnt, u may need a new brushroll which can be found on ebay, or dirt devil's website ... Dirt Devil M085580 Featherlite Plus Upright Vacuum

Bissell powersteamer # 1697 filled it with water and soap in the container and the motor runs but it doesn't work, water won't go through and it won't pick up anything. Checked and the belt is fine.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Have model 3576-6 Bissell Cleanview II and drive belt keeps slipping off peg that is sticking out from motor pulley causing vacuum to stop working properly and brush to stop moving properly


... Vacuums

Why do the belts keep breaking - Bissell 3576 CleanView II Bagless Upright Vacuum


Hi there,\012\012\012Well the problem happens due to the belt If the belt not installed correctly, the rubber belt will grate against one of the components in the roller brush housing. The friction of the belt against the housing produces ... Bissell 3576 CleanView II Bagless Upright Vacuum

Bissell powerforce vacuum belt keeps burning and breaking


... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a bissell 1698 powersteamer. i have already cleaned heater and completely cleaned all parts , checked the mix piston, checked belt. it will not shoot water or mix. the motor runs, it will **** water and the brush turns. is it the pump and does the pump just shoot the soap?


Pump is probably bad. When you put the lid back down, did you put the piston on the bottom of the smart mix knob? Also the smart mix knob should be in the water only selection when the top is pushed all of the way down. Also sometimes the flow ind ... Vacuums

Dyson dc 14 the belt keeps breaking with the smell of burning rubber looks like the motor spindle does not turn any solutions


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My daughters X-Treme Scooters | X-360 - 350 Watt Electric Scooter - Pink the fuse keeps breaking or blowing in it. Do you know what could be causeing that? Please help she really loves her scooter and we dont have a clue nor a manual to see what is wrong with it. It will run until she pushes the gas all the way and it gets hot.


Hi, be sure you are using the right amperage fuse in it. Check any exposed wires on it they may have got skinned up, causing a short and blowing this fuse. You say it gets hot when she gives it full power, so its blowing when its drawing the most amp ... Vacuums

WE HAVE A DIRT DEVIL ULTRA VISION TURBO VACUUM MOD 87800 AND ITS BREAKING BELTS AND THE MOTOR SMELLS WHEN WE RUN IT


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I have a Bissel Proheat Pro-tech. When turn ON the motor running but not work. The belt still good but tho rotor not turn. Please help me to fix.Thanks


Is this the carpet cleaner Proheat?I have a Proheat 2X and it wouldn't disperse water unless I used the Water Rinse setting. I found water came out and was suctioned properly, but on the Light Clean, Normal Clean, and Heavy Traffic setti ... Bissell 9200 Upright Vacuum

My Bissell Powertrak Cyclonic Vacuum has started running REALLY loud! I have cleaned the filters, checked for any clogs in the hoses and replaced the belt, but it stull sounds like a jet plane! Could it be the motor? Any suggestions!?


... Bissell 6594 PowerForce Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1383 seconds