Having problems with your Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum ?

Belt broke on cleaner for the pump how do iget the new belt back on ?


Answers :

Repair Help & Product Troubleshooting for Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Belt broke on cleaner for the pump how do iget the new belt back on ?


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha


I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a Bissell Model 8905 Carpet Cleaner. I was going to replace the belts because the pump belt broke, but when I turned the machine over, a small piece fell out. It looks like a tensioner arm because it has a small round part at each end on opposite sides of an arm that has an offset or "dogleg" in it. I am looking for an exploded parts diagram to determine what the part is and where it came from.


... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a Bissell 1623-1 Steam Cleaner. It will work good for about 2 minutes and then after that it will not dispense cleaning solution on floor or through the hand held wand.I have replaced both drive belts with no improvement. I have cleaned it and found no obstructions in hoses and spray nozzles, put back together and it still will not dispense. Is it possible the pump or solenoid is no working? Aaron


... Bissell 1623 Steam Cleaner

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?


Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum

Need help installing a pump belt on my bissel steam cleaner


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have the Bissell upright cleanview bagless vacuum cleaner. My belt broke and someone else took it off. I bought a new belt but do not know where it goes on the cleaner. Please help


Easy to do. Unplug the vac. Turn the vacuum over and look for three finger latches on the bottom behind the brushes. Unlatch these and pull the faceplate off. Then, grab one side of the brush and pull straight up (they just sit in grooves on the ... Bissell CleanView 3596 Bagless Upright Vacuum

Changing belt while changing the brush belt the cog/gear fell out, ive tried to push it back it but it doesnt seem to stay...is there a way to snap it back in or is the unit broke?


You will have to replace it, and it comes on the pump not separate. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Belt broke I have a bissell powersteamer and a belt broke and came out the bottom of it. I dont know how to put one back on it


There should be an access panel on the top side of the cleaner. Pry this open with a screw driver and this should get you access to the area where the belt can be changed. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

We have the pet steam cleaner bissell 12 amp, we tried cleaning off the brush, because the cleaner wasnt sucking up the water sufficently. a screw came out along with the belt roller, and we have no idea how to put the screw or the belt back on.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No


Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of


Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

Belt type Ok, thank you for the help! I did have the top off, but did not know the taking the motor loose trick, thank you for that! Now I have a couple of more questions, and thank you so much for all of the help! I got a belt from sears, & the sales guy sold me an off brand belt. It looks just like the belt that broke, although do you have to force the motor back down into place? I think it may be the wrong belt? I have looked on the Hoover website & they do not even have parts listed fo


The belt number is 91001028. The belt will be snug but not real tight, so the belt you got may not be the right one. Most repair shops for vacuums should have this belt in stock. ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Have the empower upright cleaner. belt broke. can not find part #36528-040belt. can find a lot of hoover belts but not this #.Is there another hoover belt that will work on this vac?


No. if the wrong belt you will have problems. This is a common belt for Hoover, it used to be 36528027, but the number changed to the 36528040, also 40201190 is the newest number for this belt. Most repair vacuum repair shops should have this belt. ... Vacuums

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Bissell 7950 ProHeat Self Propelled Carpet cleaner Replacement Pump Belt part 215-0628


Normally, there is a post sticking out of the retainer to remove it. If the post is broken off, then you will have to lift the black arm and wiggle it at the same time and the retainer will pop up so you can remove it. On the belt side, the retainer ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Belts I have recently bought new belts and when I installed the green light only comes on sometimes and I can smell rubber burning. The last belt broke very quickly so I am assuming that when I put the vacuum back together I am doing something incorrectly. Can you help instruct me?


Recently received a kirby from mother in law and don't how to change the belts ... Kirby Ultimate G Bagged Upright Vacuum

We have had three belts break on your hoover vaccum cleaner u5472-940. It is easy to replace, you just remove the plastic part over it, put belt on wheel and then put it back on. Any idea on why the belt keeps breaking?


Sometimes when you buy belts from the walmart or target, they are not at the correct specification and they brake as soon as you turn on the machine. i would suggest that you buy these belts from the company. ... Hoover F6021-900 Steam Vacuum

Replacing the Brush and Pump belt on Bissel Steam Cleaner 1901


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Can not put back the red clip to my pro hea t deep cleaner i replaced belt cannot put back red clip retainer


... Bissell ProHeat Deep Cleaner Upright Vacuum

Our belt broke and now i can't find out where it should go back! The second one broke too so I thought that maybe I was putting it in the wrong location>


Check the brush make sure the ends spin freely if so put the belt on spin the brush with your hands 3 or 4 times around the belt will seat its self ... Vacuums

The belt broke and there was a bit of a burning smell - I attached the carpet cleaner attachment with integral belt but there's no electric power


Here is the belt you need:Kirby Ultimate G Belt ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0686 seconds