Having problems with your Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum ?

Belt I have a bissell pro heat model number7901-1 and i dont know how to put the belt back on. The old one broke and i cant find my book.

Answers :

First take off the cover on the left side of the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put over the pulley on the pump and then stretch it to go over the motor shaft. Then put back together.
Repair Help & Product Troubleshooting for Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Belt I have a bissell pro heat model number7901-1 and i dont know how to put the belt back on. The old one broke and i cant find my book.

First take off the cover on the left side of the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of

Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

Belt broke I have a bissell powersteamer and a belt broke and came out the bottom of it. I dont know how to put one back on it

There should be an access panel on the top side of the cleaner. Pry this open with a screw driver and this should get you access to the area where the belt can be changed. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Belt replacement cant figure out how to put new belt on...old one broke....

Hello : \015\0121:Unplug your Hoover vacuum. Turn the vacuum up-side-down and place the motor and vacuum portion on a counter top with the handle hanging down toward the floor. This makes it easy to work on the underside of the vacuum por ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

I have a Kirby Heritage II which normally works amazingly well, but it's not playing at all nicely today - and of course we have apartment inspections tomorrow. *dies* The belt broke today (as did the replacement belt, which I'd bought at the same time, so apparently the rubber was old), so I went over to Stark's to get some new ones - but it still won't cooperate. I've taken the head apart and put it back together several times, to be sure that everything is properly seated, but it's just not

... Kirby Heritage II Vacuum

Our belt broke and now i can't find out where it should go back! The second one broke too so I thought that maybe I was putting it in the wrong location>

Check the brush make sure the ends spin freely if so put the belt on spin the brush with your hands 3 or 4 times around the belt will seat its self ... Vacuums

I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?

There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina

Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt

You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum

I have bagless samsung air track 2000w tein cleaner vaccume cleaner..it has only one switch for on and off...cant find a switch to put the cord back????? .

... Vacuums

Don't know how to replace broken belt on eureka pet pal upright bag less put one on broke immediately

... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

The little toothed belt on my bissell shampooer broke got a replacement but don't know how to put it back on Stark's where I bought the belt wouldn't help me man said he isn't a mechanic. well neither am I so could you send me a diagram I could follow? Thanks

Hi!  Your question has come up under Bissell ProHeat, although you don't actually specify that model. Assuming it is, the belt change operation is quite simple but hard to describe in words (it will sound much more complicated than it actually i ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My Necchi supernova ultra mark 2 (50 year old) sewing machine's belt broke (13 inch length). I'm having trouble finding one on-line. Any idea where to get one?

I have the same machine and I see the belt has been replaced. It's a Singer belt. You might wanna try that. ... Vacuums


Put the V belt on the pulley first, then the flat belt, put it over the motor shaft or pulley, then you have to stretch it to go over the pulley next to the V belt pulley. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.

Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

I took apart my 1697 model cleaner to check the hoses for leaks now I dont know if I put the hoses back on right. I cant find a diagram on how it is suppose to look.

I found a manual that has an assembly guide for your model:\015\012http://www.bissell.com/downloadfile.aspx?id=554\015\012\015\012\015\012\015\012\015 ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

How do you change the belt cant find where to take apart to put new one on

Follow the procedure below:\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Eureka 4874 Bagged Upright Vacuum

We had to take the machine apart just to see that the belt had broken after only 5 use's . We can not see how we are ever going to put the new belt back on. do you have instructions on how to take the belt off and how to put a new one on? Please send me one.

I have a Panasonic MC-V5746 upright vacuum. According to the booklet, \015\012MAKE SURE UNIT IS UNPLUGGED.\015\0121. Place carpet-bare floor selector in "carpet" position.\015\0122. Remove lower plate (there are two screws in the m ... Vacuums

I am a professional maid and one of my clients just had her Hoover Elite Vacuum belt break. I bought the belts ... but cannot find a manual online and do not know what the model number is. I am scheduled to be in her home in exactly one hour! HELP! HOW DO I CHANGE THE BELT -WHEN I CANNOT FIND A MANUAL? Many Thanks! Lynn

This is no problem! You will need a flat blade screwdriver and about 10 minutes! \015\012 \015\012*Always use genuine hoover parts for repairs, discount store belts can be as much as \015\0121" longer than OEM parts ... Hoover Elite U5061-900 Bagged Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t

The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks

You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1

Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

My belt broke...I bought a new belt..but I do not know how to put the new on on. I took out the brush roller and put the belt around it but I have no idea how to get it to go on the part that makes it move.

Hello,\015\012Here is a link to my free online guide...\015\012\015\012http://reviews ... Kirby Ultimate G Bagged Upright Vacuum

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?

If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1034 seconds