Having problems with your Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum ?

Bissell 7901-1 The soap doesn't mix with the water when I pull the trigger, I can see the soap isn't being used when I do the carpets. What can I do, have no problem taking this machine apart.


Answers :

If the mix valve knob is turning smoothly, then most likely the cap and valve for the sop bottle is bad. Also make sure that the seal is on the cap at the bottom of the bottle and not sitting in the hole.
Repair Help & Product Troubleshooting for Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell 7901-1 The soap doesn't mix with the water when I pull the trigger, I can see the soap isn't being used when I do the carpets. What can I do, have no problem taking this machine apart.


If the mix valve knob is turning smoothly, then most likely the cap and valve for the sop bottle is bad. Also make sure that the seal is on the cap at the bottom of the bottle and not sitting in the hole. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks


HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have an older model Bissell rug shampoo machine, model # 1631. I have several bottles of Bissell 5 One carpet formula to use in this machine, however I have lost the measuring bottle that tells me the amount of soap solution to use per 64 oz. bottle of water. I sure would appreciate if you could help me.


I have a older mod. Bissell carpet machine plus mod. 1630-5 and need a floor nozzle part num.013-6194 and grip tube w/button part num.014-4181 and trigger part num.010-9406 and tube ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I recently purchased a bissell proheat 2x and have used it several times with great results, the problem I am now having is no water being released from the bottom of the machine and the gauge is not spinning. What could be the problem. I have taken the machine apart thinking maybe something is clogging it.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Just bought and used the Hoover MaxExtract 77. First time the water was extracted from the carpet. Second time NO water in tank. Now I have wet carpet. I've taken the machine apart 3 times and cleaned the filters and still the water is not extracted from the carpet.


... Hoover F6055-900 SteamVac Maxextract LS Wet/Dry Vacuum

We had to take the machine apart just to see that the belt had broken after only 5 use's . We can not see how we are ever going to put the new belt back on. do you have instructions on how to take the belt off and how to put a new one on? Please send me one.


I have a Panasonic MC-V5746 upright vacuum. According to the booklet, \015\012MAKE SURE UNIT IS UNPLUGGED.\015\0121. Place carpet-bare floor selector in "carpet" position.\015\0122. Remove lower plate (there are two screws in the m ... Vacuums

Bissell I inherited the Bissell Model 790 Steam Vac. No solution will come out. Apparently it's clogged somewhere as the previous owner appeared to have used it to vacumn up a powdered carpet cleaner. How do I resolve this problem as the machine is barely used and I would like to salvage it. Thank you


Check the belts first, if ok, does water squirt out of the hose nozzzle, if it does then the heate in the handle asm. is clogged where the tubes hook up to it. If no water squirts out, the the pump isn't working. Pull the top cover off, check all t ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I've had my Dyson DC14 vacuum cleaner now for approximately 9 months and been very happy with my purchase. However, It is used sparingly maybe twice a week at the very most. The problem is when I try to use the item on my carpet, you have to push really hard to get it to move. It's as though the suction power is far to strong. It certainly doesn't glide as I think it should. It still picks up as usual but I cannot imagine that having to 'force' the machine to move is the normal operating procedu


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The soap dispenser on my 2X is not dispensing. I wrote with this initial problem and received a reply. We did everything recommended to find a clog. To begin with, we poked holes thru the little holes on the underside with a toothpick. Next we took the machine all apart as directed and cleaned out anything that had accumulated (such as pet hair). Eventually we emptied out the soap dispenser, filled it with a hot salt water solution and let it sit for 10 min. I ran three tanks of hot water


Hello,The solution to your problem is already solved, since your soap dispenser is still under warrant,What i will suggest is that you contact the company that supply you this product and explain everything to them, it is most ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No suction i have been using mine for like a year or so. today i went to use it and then no suction. the water comes out but it wont **** it up. I haven't had any problems till now. I cleaned the little red filter but still nothing. I dont wanna take it apart with out knowing what im looking for.


I had exactly the same problem with my five-year old my Bissell 7920, and it's probably a broken pump belt.  See page 19 of your instruction manual for how to replace.  The Bissel ProHeat belt accessory pack costs $3.99 and you get a pump b ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I just bought a Hoover Platinum Collection MaxExtract Carpet Cleaner (Model No. F8100900). This is the first time I've used it and got half way through one room and the unit cut off and has no power at all. No lights anywhere. On/Off button is inoperable. I checked the outlet and it's still operating so it's not a circuit breaker issue. The problem appears to be with the machine. Has anyone heard of this happening this quickly? Is there a reset button on the machine>


... Hoover Vacuums

No spray I have a proheat cleaner. The problem is there isn't any solution when I press the trigger on the handle to use the machine to clean a whole carpet yet if I use the handheld unit it works a treat. I have tried all the remedies in the manual.


\015\012Here are 3 common things that causes this problem:\015\012\015\012• clogged spray tips \015\012• defective solenoid valve in the base \015\012• defective trigger microswitch in upper handle ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Squeaky wheel I don't want to take apart more than I have to. The front cover has been removed and I tried using WD40 on the squeaky areas but the problem has not been resolved.


... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara


... Vacuums

I have a proheat carpet cleaner model 3 7901. the problem is the brush on the bottom of the machine plus the two end parts and the belt came out. i put everything back but they popped out, they are not staying in place. what am i doing wrong or what do i have to take out to get everything in place correctly?


Hi\015\012\015\0121. You’ll need to follow this procedure to assemble your unit back together.\015\0122. Make sure the foot pedal is in the proper position.\015\0123. The SmartMix should be properly loaded into the main ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Water and soap not dispensing on my bissell proheat clearvie carpet cleaning machine at correct rate; how do I solve this problem?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My Eureka Atlantis Express is brand new - never used. I took it out of the box, read the manual, filled the soap and clean water tanks, put them in. I lifted the machine off the counter to take into the living room but all the water came running out of the bottom all over the kitchen floor. I can see where the little white plastic piece sticks up into the water release valve and lets the water out. How do you stop this? Can it be fixed?


... Eureka 2553A Atlantis Handheld Wet/Dry Vacuum

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?


Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums

My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks


Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums

Water and soap not dispensing on my bissell proheat clearvie carpet cleaning machine at correct rate; how do I solve this problem?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Water leak I just bought this steamer a few days ago, and already I am having problems, when I fill the water tank that your suppost to fill the water runs out before I even turn the machine on. I have tried using plugs to keep it from doing this just so I can shampoo my carpet, this seems to work to a point, considering the fact that there are two holes underneath close to the brushes and one just a little ways back from that location. Do you know if this is something that should have plugs or


If you just pruchased this, then it is under warranty, take it along with proof of purchase to a warranty repair shop and have them fix it. If water just runs out, then there may be a seal missing or a water line off. ... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do


I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum

Hoover filter Since I cleaned the filters the dirt collects there instead of falling into the reservoir. I've tried taking apart and reassembling them, but the problem stays. I'm having to clean the filters every time I use it. Any ideas?


... Vacuums

I have an old silver king cannister vaccum (R2-D2 star wars) Im looking for filters. When you take machine apart there is a donut looking filter under motor(top of vaccum) that protects motor. I cant find them anywhere. I found the other filter the model uses (disc filters) HELP!!!


I'LL DO A SEARCH ON LONE BUT THE MODEL NUMBER WOULD HELP ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0844 seconds