Having problems with your Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum ?

Can't clean out a part; need help

\015 Behind the floor nozzle window neer the top narrow part, there is a dark gray plastic piece that is clogged with hair and lent. I cannot see how to remove this piece to clean behind it. Please advice. Removed two small phillip scews on each side at bottom of nozzle window but plastic face would not come loose. Thanks for your help.\015\012\015\012David\015

Answers :

The nozzle will seal very tight along the sides, pry up with somethin like a flat blade screwdriver to pry it loose. When you re-install it, make sure the 2 tabes at the top edge of the window snap into the slots first before putting it all of the way down. If you don't then the bucket will sit up slightly and won't suck up the water.
Repair Help & Product Troubleshooting for Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Can't clean out a part; need help


The nozzle will seal very tight along the sides, pry up with somethin like a flat blade screwdriver to pry it loose. When you re-install it, make sure the 2 tabes at the top edge of the window snap into the slots first before putting it all of the w ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I lost the detergent container on my Hoover Model F7220-900. Its a small plastic bottle that sits on the back of the clean water tank. I called the help desk and they told me that they no longer make that part so I have to pay $55 to replace the whole tank which will come with a detertent container built in. The whole carpet cleaner was only worth about $225 new. I don't feel I should have to pay $55 for a part I don't need but the machine is worthless without it. Any good ideas to solve th


... Hoover F7220900 SteamVac V2 Upright Vacuum

Irobot roomb will not work. I've discharged the battery and recharged for 16 hours. Acts like it is going to come on but sort od revs up and then gives a series of 6 or 7 or 8 beeps.. Goes so fast I cant count them. I've cleaned everything. Aftertyring a couple to Times, it seems that the battery discharges... Clean light goes red. Please help... i need this thing to work!,,


... iRobot Roomba 550 Vacuum

My Dyson Animal is not picking up very well in the drive position. With the hose the pick up is still very good. I have had it for 2 yrs now with very little problems. I have cleaned out all areas etc pipes, the brush underneath and cant find any blockages. The noise of the dyson is the same as usual. Could you tell me if there is a part that it sounds like it needs?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We have a Singer 626 sewing machine. It's an old mechanical machine with heavy metal parts. The stitch selector was stuck, I removed the top and helped the selector to move. when I had to move the selector again, it was stuck and I pushed too hard and broke a component. I can fix the machine if I had a repair manual. I need to buy a repair manual. How and where can I get one? Thankjs Charlie PS. Im pretty mechanicly inclined and I was able to clean the machine and get it to work after


... Vacuums

Shark V15Z I need to know how to apply the bag part when I clean it out. I know there are directions in the manual for this model. Can you help?


... Vacuums

Hi I am wondering if someone could send me some (Schematics for a Bissell 9300-1) I took it all apart to clean out all the ( Hard watter out of the hoses) and now I cant remember where all the hoses go,I need to see where all the hoses go so I can hook up if someone could help me out! Thanks!!


Hi, you should be able to download the manual/manuals you need on the following web page. Just paste the following onto your search bar. I've used this site to find manuals before, it can be trusted. Good luck!\015\012http://www.manualsonline. ... Bissell Vacuums

I have a typhoon cyclonic 2400watts hoover and i cant find anywhere that sells parts i need the long stretch pipe could you help by telling me where i can get 1 from


... Typhoon Vacuums

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!


... Vacuums

Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina


Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum

Hello! Help!! The brushbar on my dyson ball vaccuum will not spin. I took out the brushbar and cleaned it, then reset and cleaned out the filters too but still doesn't work. Do you think I need a new rectifier? Thanks for your help.


Sorry this is not a solution. But after reading your problem and other people with the same problem, i just wanted to say i have a Dyson DC24 ball and have only had it 1 year and the exact same thing has happend it is spotless inside and out includin ... Dyson Ball DC24 Bagless Upright Vacuum

I've cleaned a few areas and now the blue nozzle part with the dirt needs to be emptied. I do not have an instruction manual and can't figure out how to open or detach the blue nozzle part to empty it & clean it out.


Release the handle under by the front wheels. It will then pull out. Once you pull it out,on the frame there is a diagram showing out it comes apart. ... Sharper Image SI570 Steam Wizard Handheld Wet/Dry Vacuum

Vacuum has new bag but won't pick up dirt. Cleaned flat filter and it made it worse. Do I need to replace rectangular filter or can I clean it. If so , how? If not, do I need to take it in for repair, ir should I get new parts? Thanks!


It's clogged somewhere. Disconnect the hoses where you can and check for obstructions. Run a coat hanger down the hose if you need to to clear the obstruction. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I'm not sure if it needs a good cleaning or a new belt. I called the vac place & they want $80 for cleaning it...more if it needs parts of course.


Try calling someone else a tune up should be about $40-45. Most likely it is the belt though. The belt should be about $6 or 7 bucks. ... Electrolux 4870 Bagged Vacuum

I have model # EC2T-36 HPF and TCP# 12536Q and I am looking for a repplacement ballast and a light cover but I am having trouble finding the parts department online and the 1-800 number on the fan is a musuem line. So I need help to get these few parts. can you help please? Matt 937-572-2386 Thank you, Matt


... Vacuums

The female part of the catch which holds the lid to the accessories compartment closed has broken. This forms part of the handle to the vacuum cleaner.We've had the vacuum for less than a year but cant find the receipt so i think i will just have to pay for the parts. What is the part called that i need or the part number and where can i get it from. Many thanks


Even if you do not have the receipt you are still entitled to one or two year warranty.Since appliance sales are recorded after-sale by manufacturer, you need to contact the manufacturer to validate the warranty and get the replacement. ... Nilfisk Vacuums

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have the eureka bagless capture. The main hose is what I am interested in. I cracked the end of the hose where I would attach other parts such as the slim attachment for corners and to get inside the pillows in my chair, The part that I broke is on the very end of the hose. I had the plastic part clogged with some hair and during the process of getting it cleaned out, the part that I am speaking about is broken. Can you help me. I thank you, Mo moss


Change the hose part try a company called cds they r in the midlands but they courier parts\015\012out 2u dont have their no 2 hand u will need the model number try the\015\012web marting ... Eureka Uno 2998AZ Bagless Upright Vacuum

No Suction I have a dc18 dyson and it had lost suction from the main hoover and the hose part. If you remove the dust collection part there is suction from the hole behind that part. I have cleaned all part to this hoover but the problem is still there. Any help would be apprieciated. Thanks


Filter removal step 1Turn power off and unplug the machine.\015\012\015\012To remove the washable filter: Rem ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I have a kenmore vaccum i order a new part need help in removing the old part.


... Kenmore Vacuums

I am wondering how I can clean the inside of my bissell spotlifter powerbrush hand held cleaner? I want to clean the part where you suction up - it is full of gunk and hair and I can't figure out if it comes apart or not so I can clean it. Can you help?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=49876&thid=506980\015\012I am wondering how I\015\012Posted by carriespets on Apr 12, 2008\015\012I am wonde ... Bissell SpotLifter 1716 Bagless Handheld Vacuum

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

I need a replacement part for the S3325 Shark ultra steam blaster hard surface cleaner: part #22, Accessory Adapter, on page 3 of the owners manual. Euro Pro shipped me a totally wrong part. Can you help me find this adapter? Thank you.


... Euro-Pro S3325 Handheld Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0822 seconds