Having problems with your Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum ?

I have a bissell proheat multi surface 2x model 9200-T 08296C. It stopped spitting the water and soap out on the floor, but still sucks from the base and hose. I took it apart to see if anything was disconnected but saw nothing. Please help!


Answers :

I Had the same problem with my model 79011...take the upright handle apart & you will see a pot-metal rectangular box midway down the lower section of the handle with wires on it & 2 hoses attached. This is the water heater unit. LET IT COOL IF YOU JUST HAD THE UNIT ON AS IT WILL BE HOT!!! Take the hoses off & carefully **** the inlets out ( do NOT probe more than about an inch in) with a piece of coathanger wire. Flush heater unit out by hooking a peice of hose up to the heater unit & blow into it to flush the loosened crud out. Hook it all back up & it should work like new! What happens, is the alkalis in the cleaning solutions react with the pot-metal & cause corrosion to build up, eventually clogging the unit, thus not allowing waterflow thru it. Built to fail just like all modern junk! ;) Hope this helps! Ross
Compare it to the 7901- does it have a heating unit? My 7901 does and I disassembled the heater and cleared the clog- problem is the soap hardens either inside the lines or in my case inside the heater unit- it took me a small drill bit and a paper clip to clear it- check it out on yours
Repair Help & Product Troubleshooting for Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a bissell proheat multi surface 2x model 9200-T 08296C. It stopped spitting the water and soap out on the floor, but still sucks from the base and hose. I took it apart to see if anything was disconnected but saw nothing. Please help!


I Had the same problem with my model 79011...take the upright handle apart & you will see a pot-metal rectangular box midway down the lower section of the handle with wires on it & 2 hoses attached. This is the water heater unit. LET IT COOL ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Our Dyson sucked something up last week (not sure WHAT) and now the telescoping hose won't ****. Well, it sucks but just BARELY . I took the hose apart and can't see anything, but it makes a weird noise now when you stand the unit up and are not actually vacuuming with it. Help!


Well if the hose is completly clear the blockage is either before that or after that the brush roller should come out to clean the tube as you know also comes out make sure all are clear right up to the collector ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.


I about to say that's always a clog of some sort that causes that ... Miele S7210 Bagged Upright Vacuum

The suction in the hose of my 2 year old Dyson Animal vacuum is compromised. I may have sucked up a small cat toy or something. Regular vac still is fine. The hose "sucks closed" after a few seconds near the top. I love my Dyson! Please help.


Hi there, it sounds as though the wand handle is blocked. To test this, remove the wand handle from the hose and test the suction at the top of the hose. If its strong here, then you will need to remove the blockage from the wand handle. If the suc ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My roomba just goes in a circle and doesn't want to advance forward, on carpet or tile floor. I took it apart, cleaned it according to the manual and still the same responce. Please help.


... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

I have A BISSELL UPRIGHT STEAM PRO HEAT AND IT JUST STOPPED SUCKING I TOOK APART AND CLEANED EVERYTHING CHECKED THE HOSES FOR CLOGS AND IT STILL WONT WORK


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No suction i have a hoover supreme wind tunnel vac and its relatively new and the suction, well......sucks. It wont pick anything up! I am extremely frustrated! I picked up a ball of fuzz off the carpet and held it under the vacuum and it still wouldn't **** it up. I then shoved the fuzz up INTO the vacuum. It fell right back out. I may as well not even vacuum. Please help!


I have found more vacuums on the way to the dump because they were full. Check. Is it full?\015\012If not the air way is clogged. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have an electrolux renaissance c104a model vacuum...I got a sock stuck in the hose and took the end of the vacuum where it attaches to the canister apart. There are 4 brass pins that I cannot get back in the correct sequence to operate the vacuum...please help.


... Electrolux Guardian Bagged Canister Vacuum

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?


Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Hose The intake hose has torn apart at the base where it is attached. Is there some way I can repair it or do I have to order a new hose. The Sears store where I purchased it is of no help.


You will have to replace the hose. If you want to get it thru Sears, go to Sears.com, click on parts, enter the model number, if they have it in their system, you can find the part there and order it. Or take the model number and go to where someon ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoses I have a bissell took it apart cant remember how the hoses go back is there a diagram I can look at I have the scehmatic to the whole machine but not the hose placement help


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hi I am wondering if someone could send me some (Schematics for a Bissell 9300-1) I took it all apart to clean out all the ( Hard watter out of the hoses) and now I cant remember where all the hoses go,I need to see where all the hoses go so I can hook up if someone could help me out! Thanks!!


Hi, you should be able to download the manual/manuals you need on the following web page. Just paste the following onto your search bar. I've used this site to find manuals before, it can be trusted. Good luck!\015\012http://www.manualsonline. ... Bissell Vacuums

My dyson has two gears as it were! One for normal suction and the other for deeper cleaning. There used to be a real difference in the performance between the two options, also the noise changed when you swithched from one to the other. This no longer occurs. I have taken it apart according to your instruction, cleaned all the various bits but still no luck. The cat fur is still clearly visible despite my best efforts. Can you please help!!!!


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a sock caught in the vacuum cleaner hose it is about 5 ft past the beginning of the hose and very stuck I have tried sucking it to the canister but no luck please help the suction is almost too good but now it is a major problem!


Take a coat hanger and straightn it the best you can then make a small hook on one end of it and if you can unhook one end of the hose straightn the hose and try to go fishing with the coat hanger. ... Vacuums

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

I have a Bissell ProHeat 2X which releases the water/shampoo mix fine, and will suck up using the hose, but will not suck up using the main floor unit. Have checked it all out, and there do not appear to be any blockages. Help please


The vacuum on its back then look under the front where the water comes\015\012out, you will see few little round holes now the chances are these\015\012holes are blocked so get something long like a pin and poke these holes\015\012through you should ... Vacuums

Absolutely no suction in hose,, already took apart the hose from top to bottom cleaned all that can be cleaned still no luck what can I do


Hi,Often the hose can pug and it can be very hard to get it out... some thing can push sideways when you run something through the hose but then close it up when the suction is applied...Make sure to stretch out the hose and run something ... Vacuums

Clogged hose I just accidently sucked up a sock and now I have no suction. I have no idea how to get the handle off and doubt this would help anyway. It is an Electrolux central vac. Help please!!!


If you have a drain auger then you can stick it in until it won' go any further then you have hit the sock.turn the cable and grab the sock and pull it to the surface.please leave feedback ... Electrolux Central Vacuum

I was vacuuming and part of a towel got sucked up, but not into the hose, and now it isn't working. I turned it off, unplugged it, and the hose still works with the attachments, it is just the base


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=833476\015\012Generic problem for all Vacuums\015\012I was vacuuming and part\015\012Posted by melly648 ... Vacuums

Model number f 5912-900 hoover steam vav with clean surge.This is not the f5914 model........my new machine has 10 min. on it...in mid use it has stopped sucking and now is blowing more than anything, I took the front clear piece off as well as the black cowling/shroud and can find no obvious hoses to un-clog nor anything else to un-clog for that matter...I am looking for advise to fix this thing now, myself


Here is a list to go by for no suction problems that you can follow along with they are common proble\015\012Problem #1 Steamvac is not Sucking!If your Hoover Steamvac was working properly and suddenly it is not sucking any ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a dc18 vacuum and though you can feel the suction from the hose when you put your hand over it, it will not pick up anything from the floor at all. I have cleaned the hose, filter and the holes from inside the canister and still nothing. Help?


Here is a Link to one of my Tips that should solve the problem you are having:www.fixya.com/support/r6311178-vacuum_brush_bar_not_spinning ... Vacuums

The bottom of my dyson dc07 original is not sucking and the roller is not rolling but the hose is sucking and i have cleaned the whole thing PLEASE HELP ME!


U need a new clutch assembly\015\012refer to this site for more details on dyson vacuums and to submit a repair form\015\012\015\012D ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson dc17 animal will pick up via the hose attachment but there is no suction when you use the regular vaccuum on the floor - you can hear the difference in the suction once you put the floor part down - we took it apart - cleaned it - checked all hoses - still does not work????


Hi its Darran at Dyson.Check that the brush control dial is in the centre position when upright and then moves forward when the head is released. If the brush bar is still not spinning when switched on in the vacuuming position, check th ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

No suction i have a bissell lift off revolution vacuum. I have cleaned all the filters and emptied out the canister made sure that the hoses are not plugged but it will not pick up unless you use the hose. the floor brush is clean and still no suction coming from under the vacuum... could you help me please


Is there a blockage in the small hose in the bottom of the machine \015\012take of the pod and you will see the small hose, \015\012Is the main hose pushed into the bottom housing ... Bissell 37603 Upright Vacuum

Dyson animal We bought a Dyson Animal from Sears a few years ago along with a service contract. We took it each year to be serviced. One year I took it because it lost it's suction. They sent it to the factory, but it came back still not working right. We did the same procedure over ands over many times than I can remember. I now have the cleaner in my garage and am using my old vacuum because I just can't seem to get anywhere with Sears. Please help me. We paid almost $600.00 and now it can't b


As someone who works for Sears, let me just say right now.. The service contract you bought sucks.. and does not really do anything for you. it was just a wast of money ( they have a new one now.. thats so much better because you get your money back ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1095 seconds