Having problems with your Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum ?

No WAter My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle.


Answers :

Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole, this is for the soap bottle also, there is a seal on the bottom of it as well. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines. Is the top cover and the base tight together in the back, sometimes the top breaks loose and it will raise up and it can't spray, just re-fasten it down.
Repair Help & Product Troubleshooting for Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No WAter My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle.


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Dear Sir: I just purchased a Bissell Rug Shampooer at a garage sale. The only thing I find for a model is on the back and it says Model 1695 there. Nothing on front. It is Navy blue and has a grey tank on it with a smaller one inserted at bottom of the large tank. It has two switches on the back of it and the trigger switch at the handle. The cleaner works, BUT, it does not extract any water back into the tank that is to pick up the dirty water. Could you suggest what I may look at t


... Bissell Vacuums

I have a Bissell Proheat model 7901. When I pull the trigger on the handle, there is no water flow. The brushe revolves and the unit vacuums any water spilled on the floor. Could it be a failed pump or kink hose or ? Thanks Zap


Take the handle apart and put spring back into place. ... Bissell Vacuums

My Bissell model 8910 pro heat will pump solution or water for like the first couple times you pull the trigger as you can see the mixture window spinning. After that it stops spinning and nothing else will come out until you turn the machine off, and restart. Then again same process works for a couple trigger pulls then quits.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Shampooer I have a rainbow e series and my shampooer is not working. The tubes do not seem to be clogged and it sounds like it is trying to work but we cant get the water to come out. We pull the trigger and nothing no soap, no water, nothing. Can anyone help?


Aqua mates have an o-ringed valve assembly that go bad regularly reccoment having it replaced by local vac shop ... Rainbow E series Canister Wet/Dry Vacuum

Bissell Powerease Lighweight Deep Cleaner. (Shampooer) After I fill the solution tank with the solution and water, I put it in it's slot, but all of the contents just come flowing out. I have only used this machine twice and it worked ok. You are supposed to press the trigger and the solution sprays out and then release the trigger when you want it to stop. But like I said, now I just put the tank on and all the contents come flowing out. I don't know what's wrong or how to stop it.


... Vacuums

My lightweight hot tap water bissel carpet shampooer will not stop dispensing water. The trigger doesn't seem to be able to close the nipple like cover. I cleaned my machine well. Is there a cable involved here. Could it just need a vinigar treatment ?


Hi Sue. Sorry to hear about the difficulty you're experiencing. You may want to have one of our Authorized Service Centers inspect your machine.Here's a quick link to help you locate one in your area: ... Vacuums

The tool attachment for the hose on my Bissell ProHeat 2X CleanShot won't spray soap or water. The bristles on the tool rotate without a problem and the suction is working fine, it just won't spray water when I pull the little gray trigger on the tool.


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell CM 2000 shampooer does not seem to be pulling in and dispensing the shampoo as it should, although is spraying the water just fine.


... Bissell Vacuums

I have a bissell proheat 2x upright 10 row 12 amp and the water will not discharge when i pull the trigger


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Asking again. Better wording? My lightweight Bissell carpet shampooer is continually spraying cleaning solution. The sucking action works well but can't keep up. This unit does NOT HAVE A HEATER. This is a simple unit. Is there a cable going down the handle from the trigger? ( it feels like that's the way it works. Could the drain be plugged. Also it will only use 1/2 a tank of solution at a time. Then must be filled again


Hi Sue. I understand how frustrating this must be. I'd like to help you with troubleshooting steps, but need more information.\015\012Here's a quick link to contact us: ... Vacuums

Bissell ProHeat2x carpet shampooer does not dispense water when you squeeze the trigger


This can be one of 4 things the belt on the pump as waren (it may not seam ware but replace it if you can ) the water jets by the roller are bloked ( x2 red ) the pump as faled or this on about 2 in 10 the heter is bloged this hapens then the sope or ... Vacuums

No water comes out when trigger is pulled - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


Hi Karen! Sorry you're having difficulty with the spray on your CleanShot. Here's a quick link to troubleshooting steps. \015\012 ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Has a Bissell, Pro Heat 2X rug shampooer. It powers up & and the motor runs but the brushes are not rotating and water is not being dispensed.


Brush roller not working and water not dispensing was mostly caused by a brush belt being broken or is out of place.Turn the machine off and unplug it if the Brush roller do \015\012not turn. Remove any objects caught in the brush roll. A ... Vacuums

I recently purchased the Bissell Proheat Clearview from a flea market. Used once for a demo. I tried to use it yesterday, and while the handheld upholstery attachments work like a charm, the scrubber itself does not release any water when the trigger is pulled. Any suggestions?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Bissell 7901-1 The soap doesn't mix with the water when I pull the trigger, I can see the soap isn't being used when I do the carpets. What can I do, have no problem taking this machine apart.


If the mix valve knob is turning smoothly, then most likely the cap and valve for the sop bottle is bad. Also make sure that the seal is on the cap at the bottom of the bottle and not sitting in the hole. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My bissell proheat rug shampooer will not realease the water or the cleaner nor does the indicator spin


That means that you need to replace the pump belt. Here is the belt you need to get it working again:Bissell Proheat Pump Belt ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Can't get any water to flow through my bissell proheat rug shampooer


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Hey there, a friend of mine has a bissell pro heat 2x turbo, that is spraying no water on the floor setting, the pump works i assume, as the machine vibrates when the trigger is pulled, how would i troubleshoot this problem.


Check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- Check for deb ... Bissell Vacuums

We just used our bissell pro heat 25A3/64D9 series and the top half of the handle is not secure. Infact it flies off in my hand as im cleaning the carpet and it almost hit me in the face!!! It just connects to the lower half but there is nothing to keep it secure. If it is not tight the trigger to squirt water doesnt work and I am stopping and starting. It looks like a major design flaw.


I have a replacement pump belt for my Bissell #25A3/64D9\015\012but cannot find the instructions as to how to put a new one on. My son replaced the last belt, and of course he doesn't remember what he did. Is there any way you could please dire ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Water doesn't come out my Bissel rug cleaner model 7901


The flat belt on you machine has an access panel to it from the side of the machine. That belt runs the pump if it is broken or came off the machine won't pump. \015\012\015\012Check to make sure both of the red/black circular rubber gask ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Steam doesn't come out anymore when I pull the trigger. I think the water in the tank is getting hot, but when I pull the trigger, only a little water comes out. No steam


Try putting some white vinegar in the tank to dissolve any hard water deposits. You should use only distilled water in this machine. Don't try to clean anything with the vinegar in it, but take it outside to run the vinegar through. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Bissel shampooer I have a bissell shampooer powersteamer power brush model 1694-W. I cant get it to dispense water onto the carpet anymore. I think it's because I let my 3 year old ride on it while I was shampooing. I assume I have depressed some special little part that is now broken or mashed or something. Stupid I know....


Yes there is a belt on the side that will need to be changed ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I got my bissell for $7.50 from a thrift store, if you can believe THAT. Used it for the first time today after reading the manual online first. After filling the clean water bladder full of hot water and setting everything up the way I wanted, proceeded to turn things on and go for it. Well, the water/solution just kept coming and coming, without my finger on the trigger. Obviously something is jammed in the open position but where? The trigger moves freely.


This is the answer I got from Bissell:Please\015\012check the gasket at the bottom of the tank to ensure it is attached and\015\012not lodged in the reservoir of the machine. If this is not the problem,\015\012take the machine for i ... Bissell 8910 ProHeat Clear View Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0816 seconds