Having problems with your Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum ?

How to clean

\015 Floor nozzle window\015

Answers :

I have found this so i think this answers my question.




\015\012\015\012\015\012\015\012\015\012Question\015\012 \015\012 \015\012\015\012 \015\012 \015\012How do I remove the clear floor nozzle window on my machine?\015\012 \015\012 \015\012\015\012shim.gif\015\012\015\012 \015\012 \015\012Answer\015\012 \015\012 \015\012\015\012 \015\012 \015\012Before starting, please be sure the machine is not plugged in and the machine handle is reclined.

To remove the clear floor nozzle, first detach the phillips head screws located at the base of the clear floor nozzle. Then, remove the tank in tank assembly. Next, remove the rectangular gasket at the top of the nozzle, and pull the clear floor nozzle forward to remove the tabs from the notches. This clear floor nozzle is removable so you may be able to access this area and clean.

When putting the clear floor nozzle back in place, please be sure the tabs at the TOP of the nozzle are properly inserted into the notches provided. If you do not have the tabs in place properly, you may have a problem with the machine's suction.

Rotate the window down into place, replace the screws, and replace the rectangular gasket.

If you would like additional assistance, please contact BISSELL Consumer Services at 1-800-237-7691, Monday - Friday 8 a.m. to 10 p.m., or Saturday 9 a.m. to 8 p.m., ET or email us by clicking on the Email BISSELL tab at the top of this page.

Reminder: When you have completed the deep cleaning process, it is recommended to return the SmartMix dial to "Water Only" prior to storing the machine.\015\012 \015\012 \015\012\015\012shim.gif\015\012\015\012 \015\012\015\012 \015\012\015\012\015\012\015\012 \015\012How well did this

Repair Help & Product Troubleshooting for Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?

... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano

... Electrolux Vacuums

Dosenot seem to clean the carpets as good as before, we have cleaned the filter and keep the canister cleaned. What else might it be; I bought it for the express purpose to clean animal hair off my carpet?

Hi there,I'm sorry to hear you're having difficulties with your DC17. This machine should have no problem dealing with animal hair, so if it doesn't seem to be picking up as well as usual, this may be due to a blockage. The easiest way to che ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have the Hoover max Extract 77 and when I'm cleaning the carpet, the clean water tank leaks on the floor, even if I'm not squeezing the trigger. The clean tank doesn't leak when I fill it, but once I place it where it fits and start using the vacuum, the clean water drains out on the floor. The dirty tank fills up, so the suction works, but, I don't know what is going on?

... Hoover Vacuums

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)

I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!

Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

I have a Mr Coffee PSTX Series coffeemaker, the clean light came on and I started the cleaning process, about 20 minutes into it, an alarm went off, the cleaning light was blinking and I can not clear the alarm. It has not finished going through the cleaning cycle and is frozen on with the alarm. I can not clear it. Please advise.

... Vacuums

Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.

I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!

... Vacuums

Roomba keeps saying clean brushes yet are clean!

Make sure you take off the little cap at the end (the one that spins -- just grab it and pull it straight off) and clean under it too. The rest of the brush may look perfectly clean but what happens is that hair gets stuck under spinning cap and, li ... iRobot Roomba 530 Robotic Vacuum

I am wondering how I can clean the inside of my bissell spotlifter powerbrush hand held cleaner? I want to clean the part where you suction up - it is full of gunk and hair and I can't figure out if it comes apart or not so I can clean it. Can you help?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=49876&thid=506980\015\012I am wondering how I\015\012Posted by carriespets on Apr 12, 2008\015\012I am wonde ... Bissell SpotLifter 1716 Bagless Handheld Vacuum

Roomba give message to clean brushes even when I have cleaned brushes, wheels, and anything else I can find. It will only clean about 3 minutes.

Pull 2 roller brushes off.remove funny lookin yellow ends clean hair ect. also pop out front wheel and clean ... iRobot Roomba 560 Robotic Vacuum

Hoover steam vac doesn't pick up all cleaning soluation when cleaning carpet? I have clean both filters

Please look to make sure the rubber ring gasket is still in place under the recovery tank. The tube on the bottom of the recovery tank must seal to the rubber ring to get suction. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Isn't picking up lint. Will pick up other things like flecks of paper but will not get any fuzz or fibrous material off any rug no matter what the setting. This is a recent problem. Have owned the vacuum for awhile and never seen this issue before. Is it an easy fix? I've cleaned the brush, cleaned out the filters, cleaned the dirt tank. Nothing changed.

Is the brush turning on the bottom of the machine ? If not It could be clogedup with stuff or the belt could be worn on it and it will turn but as soon as it contacts the floor it will stop turning. The belt is easy to replace by removing screw ... Bissell 3576 CleanView II Bagless Upright Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a

You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

Same problem as voirjs 12/29/09 - runs a while & needs brushes cleaned w/same repeat scenario. have been doing all of the cleaning as felix80 said on 1/8/10; but it still continues the run awhile & need cleaning behavior. a more indepth solution is required.

I called iRobot Customer Support, and they are sending me a new cleaning head module. ... iRobot Roomba 560 Robotic Vacuum

Electrolux twin clean vacuum cleaner. After 5 minutes it keeps of thinking the filters need cleaning (and they don't). I re charge the power, and all seems fine and then it goes back to wanting the filters cleaned. The suction is also not working to full capacity.

Because the suction is not working fully it feels that the bags must be full and the air cannot be pulled through the bags. It could be due to 1) bags not being of correct quality. The air has to pass through them to allow all the dust to reach there ... Vacuums

Poor suction We bought a model home about 11 years ago and it had the Cental M&S Cyclonic Cleaning system. The suction has steadily been weakening. Now it is almost non-existant. I clean the filter bag in the main unit, but how clean does it need to be. Could there be a clog in the wall lines. If yes, how does one unclogg them. Thank you. I liked the system and would hate to just give up on it. Jean

This page has useful tips for unclogging a central vac. https://www.centralvacuumstores.com/cvs/trouble_help.php ... M&S Systems FX-3000 Bagged Central System Vacuum

Please clean Roomba s brushes warning will not stop after brushes have been cleaned Unit shuts off after one minute of cleaning

Clean the yellow brush bearings. Then run the Roomba without the dustbin, so that you can watch the brush while the unit is cleaning. Is it turning? If not, call customer support. 877-855-8593. Have your Roomba with you; they will want information fr ... iRobot Roomba 570 Robotic Vacuum

Cleaning Solution The cleaning solution is not foaming properly. When cleaning the carpet only a very light foam is being dispensed from the unit onto the carpet.

Is the little suds screen missing from your shampooer tank? It should be covering the hole that the hose plugs onto. Sometimes they also get lodged in the hose sideways. ... Kirby G4 Bagged Upright Vacuum

Roomba red 4100 cleans in small circle stops starts agains cleans small circle stops then status light comes on and clean button blinks.

When the status light comes on, the Roomba is going to sing "uh-oh," and then beep a number of times. Count the beeps. They're a code that tells you what's wrong with the Roomba. You can check iRobot's website for a chart of beep codes. Search "What ... iRobot Roomba Red 4100 Bagless Robotic Vacuum

My Irobot Roomba keeps saying that I need to clean Roombas brushes. I have cleaned the brushes...they are spotless. Still the Roomba will go for 2 minutes and shut itself off stating once again to clean the brushes. What up?

Perform the troubleshooting found at the iRobot website: http://tinyurl.com/nh5c8a (I promise that really does go to the right site.) That troubleshooting will enable you to determine exac ... iRobot Roomba 510 Bagless Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema

Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0362 seconds