Having problems with your Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum ?

Need a top cover for our Bissell Pro - Heat Pro-Tech 7901W as the spaces where the screws go through to the base have broke through. Where are the service or parts stores located?

Answers :

You can go to bissell.com to get help. But you can also use a longer screw with a washer to use in the back 2 holes, that will tighten up the top to the base. Or you can order a replacement top. You can check with your local repair shops to see if they can order one for you. Also check with Sew and Vac stores, they also have service and may be able to help you.
Repair Help & Product Troubleshooting for Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need a top cover for our Bissell Pro - Heat Pro-Tech 7901W as the spaces where the screws go through to the base have broke through. Where are the service or parts stores located?

You can go to bissell.com to get help. But you can also use a longer screw with a washer to use in the back 2 holes, that will tighten up the top to the base. Or you can order a replacement top. You can check with your local repair shops to see if ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The clip that connects the water base to the top of the suction area broke off..where can I get a replacement base (the part where you put the water in and has the bag where you also store the dirty water)? I have a Bissell proheat 2x

Here is the number for Bissell, they can tell you who to contact near you.\015\012Service Center Dept. Phone Number:(800) 457-1509Service Center Dept. Fax Number:(800) 517-9535Hours:M-F 8:0 ... Bissell Vacuums

Service store to buy parts for proheat 7920 - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have a kirby G4 and the mini emtor is broke off. It looks like there is a piece that connects the mini emtor boot to the base of the vacuum. I was wondering what that part is or if it is just part of the mini emtor that broke off and stayed attached.

Hello, hrjI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would tak ... Kirby G4 Bagged Upright Vacuum

I have a Kirby Generation 3. The handle spring assembly is broke, so I took it apart to get a part number. Can you tell me if there is a cross reference or something on these parts. I am unable to find a part with the same number that is located on the part I took off. The number on this spring assembly shows Kirby HA-670289B K-1. Any help finding this part is appreciated.

... Kirby Vacuums

When the bag was changed a tip broke off the bag holder and I would like to buy a replacement part but unable to locate one

... Vacuums

Model v1945zn, handel broke at base and doesnt connect to sweeper where can I find replacement part

... Shark Vacuums

I have a cuisinart smart power 7 speed blender. The black plastic base on blades broke. They sent me a new part but I don't know how to attach it.

Hi, since you are not equipped technically with the knowledge of how to replace the plastic base on the blade, i will simply advise you to take to any nearby electronic technician to replace it for you because you might want to do it yourself and end ... Vacuums

Customer service I have had problems twice with returning things at the store. The customer service representives are always so rude. I have shopped at the yorba linda,CA store for the last time. I will not shop at any Best Buy for that matter. You know there are so many stores out there with much better service. I just want to say Good Luck to all Best Buy employees.

Thanks..this is not a Best Buy service desk. But your comments will most likely be reviewed by someone, methinks. ... Vacuums

The handle BASE broke on my Shark Sweeper V1900W. Where can I find a replacement?

... Vacuums

Mystery part Bissell 1699-P. I removed the top cover and a part came tumbling out (from the rear of the machine - towards the handle area). I have no idea were this part belongs. I have a schematic of the cleaner but I can not locate the part on it. I tried to copy and paste a picture of the part but that isn't working so I will attempt to discribe the part: There is nothing stampted on the part that I can see. It is plastic(white), 2" long, 3/16" in diamater. One end is U shaped (u-shape is 1/4

One question... you haven't mentioned that the vacuum doesn't work now... as hard as this is to accept... if it doesn't effect the function... forget about it.... i could very well have been something you vacuumed up along the way.\015\012 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell 2x has suction coming out of the "base" part(when I put my had over the rubber ring that leads from base to the handle part there's suction), but there's no suction coming out of the hose. I'm not certain if there's a clog, 'cause I can't get the hose off.

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!

... Hoover Steamvac F5860-900 Vacuum

I need a relay board for a Nutone CV 450 12.6 amp dual motor vacumn unit. Where can I locate one? Part #??? Unit will run by itself, then shut off. Unit wll not run at all. It has a mind of its own. Crossed a couple of wires on one of the relays and the unit runs smooth as silk. I assume its the relay, but can't locate part number.

Why not just replace the relay? Part number 1094117... ... Broan-NuTone CV450 Central Bagged Central System Vacuum

No suction. I have followed the detachable parts no suction. I have followed the detachable parts and it seems to have suction through to the base but doesn't pick up anything significant. I have looked through the hose connecting the base but I can not see anything obstructing it.

Poor suction can be caused by obstructions, poor air flow or a compomise in the air flow (hole in the hose). Since you have started with that I would next look at all filters and clean them. First check for suction at the motor, then at accessory hos ... Vacuums

Pro heat 2x no water coming out carpet part / hand tool either

In case any of you are still trying to figure this out... I took mine into a repair shop and had the pump replaced for $66. The repairman had 6 other machines in his shop when I bought mine in. He said the pump goes the minute it runs dry, so if yo ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell 7901j pivot arm loose on non belt side - retaining clips look ok but loose part inside base - likely broken part? - and how to dis-assemble base (Maint manual?)

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.

... Vacuums

I have the eureka bagless capture. The main hose is what I am interested in. I cracked the end of the hose where I would attach other parts such as the slim attachment for corners and to get inside the pillows in my chair, The part that I broke is on the very end of the hose. I had the plastic part clogged with some hair and during the process of getting it cleaned out, the part that I am speaking about is broken. Can you help me. I thank you, Mo moss

Change the hose part try a company called cds they r in the midlands but they courier parts\015\012out 2u dont have their no 2 hand u will need the model number try the\015\012web marting ... Eureka Uno 2998AZ Bagless Upright Vacuum

HI, I'm trying to find a part for a Sharp upright vacuum. Its the back part of the handle where the cord is stored. I have taken it off but can't find any part # on it. The model number for the vacuum is EC12TWT4. I was thinking that if I could find a free owner's manual, that would give me the part # and then I could look for it on the net.

Any vacuum repair shop should be able to get it ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Lost Part I have a 6.5 hp 18 gallon shop vac ultra pro. There is a part that goes into the inside of the tank and screws into the collection hose that attaches it to the tank. This part accidentally got thrown away when someone dumped it and now I cannot attach the hose to use the vacuum. Can this part be purchased separately?

I found a manual online for the shop vac and found the part number. Did locate part online.\015\012Thanks, ... Shop Vac Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest

I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Plastic tube inside fabric bag broke cleanly at the base.

Http://reviews.ebay.com/REPAIR-KIRBY-REPLACE-CLOTH-BAG-EMPTOR-AND-OR-FILL-TUBE?ugid=10000000175652660 ... Kirby Ultimate G Bagged Upright Vacuum

Need a charging base for a Black&Decker CHV7200 DustBuster

You can find the charging base here. hope that helps.\015\012http://www.ereplacementparts.com/charger-and-base-p-102673.html ... Black & Decker Vacuums

We are unable to find a replacement part that the filter attaches to in the dirt cup on our Eureka Boss Pro Model 411. This part seals the top of the dirt cup and holds the filter in place. What is the part name or model number for the replacement?

I just called Eureka (1-800-282-2886) and asked for the dust cover lid. It was part number 61538-1. They said they could ship it to me or I could call one of the authorized service centers nearby to see if they had one. I wasn't in a hurry and the ... Eureka 411A Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0620 seconds