Having problems with your Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum ?

Bissell Pro Heat gives no flow

\015 I confirmed that tubes aren't clogged and that the belt's not too loose.\302\240 I took out the pump and blew into the suction and turned the rotor-- can't get any air through. I turned the pump over and blew and got air through.\302\240 How does this thing work?\302\240 and why doesn't mine.\302\240 I just had the pump replaced at a service center.\015

Answers :

Check the heater in the handle to make sure it isn't clogged up where the tubes hook to it. When you put the top back on, make sure the tubes are routed correctly so as not get pinched by the cover. The smart mix valve needs to be on the water setting and make sure that the piston is on the bottom of the smart mix knob. Is the seal at the bottom of the tank on the tank and not sitting in the hole or missing, tha flow indictor cap is leaking air or may even be on too tight.
Repair Help & Product Troubleshooting for Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell Pro Heat gives no flow


Check the heater in the handle to make sure it isn't clogged up where the tubes hook to it. When you put the top back on, make sure the tubes are routed correctly so as not get pinched by the cover. The smart mix valve needs to be on the water sett ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell Pro-Heat 7901-1 no cleaning solution is pumped out. The flow indicator is spinning and the belt is spinning the beater bar. Have cleaned the flow indicator, checked vavles in the solution tank and water tank and they are working properly. Also checked the trigger to make sure it works okay. Any ideas?? Moody Fan


Bissell Pro Heat shampooer - Fill the soap dispenser with extremely hot water and shampoo with only water for a few minutes. There is often dried soap in the lines. Make sure that all filters are clean. Press the soap container and the water conta ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell Pro Heat 7901 will spay through hose but not the floor and red flow indicator will not spin. So we took the housing off and after unclogging a hose running to the hearter, my husband unhooked the hose that goes to the flow indicator, blew in it and it started spinning. Put the deep cleaner back together, tried to use it and nothing. What else can we try? Can't afford to put it in the shop right now. Thanks in advance.


I borrowed my friends bissell to clean my carpet. It's the 7901. He brought it over and told me that it only sprayed out of the attachment hose. He said he couldn't figure out what was wrong. I'm no vacuum technician but, I am a mechnic. I decided to ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell pro heat flow indicator wont spin


Hey Traci! You may want to have one of BISSELL's Authorized Service Centers inspect your machine. Here's a quick link to assist you in locating one in your area:\012\012 ... Bissell Vacuums

Bissell 7700 series, pro heat all rounder. Won't spray water. Have checked the line from the unit to the spray nozzel and all seems clear. Water doesn't seem to be flowing from the tank to the end of the unit where the hose connects into. What could be the problem? Any assistance would be greatly appreciated. Thank You. Steve


HelloGrasp the cleaning solution tank, and remove it from the machine. Reinsert the tank into the machine, making sure it fits snugly in the machine. If the tank is even slightly dislodged, water cannot get into the machine. Visually insp ... Vacuums

Bissell Pro Heat Powersteamer- Filed it up, turned it on, asusual, but no water flowing from machine at any setting. Vacuum part works.


The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the way to ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

Bissell Pro Heat clear view plus...Flow indicator not turning...? Plugged? how to unplug


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell pro heat not spraying water - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Bissel Pro Heat perfect pass carpet cleaner


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How to change pump belt on bissell pro heat - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum


First take off the cover on the left side oif the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Truction for bissell pro heat turbo 2x - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum


... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Bissell Pro Heat 8910 clogged?


Why the motor sounds muffled I am not sure. When the water is sucked up, it goes directly into the tank. The motor only creates the suction so it can do that. There should be a filter on the rim of the recovery tank lid, is it clean? Other then p ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a bissell pro heat water wont come out


The pump may spin but the vanes inside could be broken or worn enough that they are unable to push water through the pump system. I am repairing a Bissell Model 8920 Pro-Heat 2X that has this very same problem.\015\012\015\012I tested all ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a bissell pro heat water wont come out


The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the way to ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Replacement electric motor for Bissell Pro Heat 2x Select carpet


Bissell proheat i can spray solution from the handle but it has no suction help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell pro heat steam carpet cleaner, not releasing water.


That means that you need to replace the pump belt. Here is the belt you \012need and a manual you can view:\012\012Bissell 7901 Belt and ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell Pro Heat 2x steam cleaner, problems!


Must likely the brush motor is bad. The top cover has to come off to check it, this is where the tank sits on. Part # 2036757 and is #35 in the pix.\015\012\015\012 ... Vacuums

Bissell pro heat 2x multi surface carpet cleaner making spots


Maybe there's not enough vacuum or it hasn't been primed enough. I have a proheat that drove me crazy till I started leaving the heat switch on. I get wads of carpet fiber that mat around brush and spit out on the carpet, so I frequently remove them ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell pro heat 2 puts out too much soap


... Bissell 8910 ProHeat Clear View Upright Vacuum

Want to use Bissell Pro Heat 2X Clean Shot. Have


You can download a user manual from the Bissell website ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I need instructions for bissell pro heat 2x cleaner


You can dawnload it from the manufacture,s website.you should go to there and dawnload it. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell pro heat will not extract water from the carpet


Try checking the top section of the machine (where the dial is located to switch it from floor to tool) and there is a little red plastic piece about 1 inch square on the inside of it. This is a lint filter that has a little door on it. Open the do ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell Pro Heat 2X will not release water or


Its probably a solenoid that controls the flow to the floor, take it to a bissell repair center, because its not an easy fix. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

My pro bissell heat leaks.


The pop sound was an electrical component blowing inside the vacuum, probably one of the capacitors on the motor control board.Water is not leaking from the tank, water is getting released because the motor is not generating enough power ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0534 seconds