Having problems with your Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum ?

Water doesn't come out my Bissel rug cleaner model 7901

\015 When I turn on the cleaner the brushes rotate but when I pull the water trigger nothing happens. Water doen't come out the bottom of it, and when you hook the hose up water doesn't come out of it either. What can I do?\015

Answers :

The flat belt on you machine has an access panel to it from the side of the machine. That belt runs the pump if it is broken or came off the machine won't pump.
\015\012
\015\012Check to make sure both of the red/black circular rubber gaskets on either solution or recovery tank are on the tanks and not stuck down inside the inlet valves on the machine itself.
\015\012
\015\012Make sure there is fluid in both tanks. Without fluid in both tanks the pump loses prime and will not work.
\015\012
\015\012If all that checks out then you are down replacing the pump, but usually when the pump goes out, you will have a short burst of water when you first turn it on and then it stops working.
\015\012
\015\012Hope that helps you out-Good Luck
Try this it happen to me take a part the upper half of the machine and look for the heater.take off one of the hoses and plow in it to see if ti is clogged it is take a part and clean out .
\015\012what happens is it gets clogged with soap and water when it drys out
Repair Help & Product Troubleshooting for Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water doesn't come out my Bissel rug cleaner model 7901


The flat belt on you machine has an access panel to it from the side of the machine. That belt runs the pump if it is broken or came off the machine won't pump. \015\012\015\012Check to make sure both of the red/black circular rubber gask ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Dear Sir: I just purchased a Bissell Rug Shampooer at a garage sale. The only thing I find for a model is on the back and it says Model 1695 there. Nothing on front. It is Navy blue and has a grey tank on it with a smaller one inserted at bottom of the large tank. It has two switches on the back of it and the trigger switch at the handle. The cleaner works, BUT, it does not extract any water back into the tank that is to pick up the dirty water. Could you suggest what I may look at t


... Bissell Vacuums

My Bissell ProHeat 2x model 9200 is not sucking up water into the tank. The water is coming out the bottom of the cleaner.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell Carpet Cleaner pro heat- water doesnt come out


The screw that is located in the center of the handle, that holds the assecory hose holder must be tight. My screw was missing, put one in and cured the problem. Sounds stupid but it worked. Got this idea off the Bissell web site. Also if you have a ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell PROheat 2x carpet cleaner the water doesnt come out of it either from the bottom or the tool can it be plugged somewhere?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

1. Bissell Model #7350-C 08249C Carpet Cleaner 2. No soap & water is coming out of machine 3. Worked fine yesterday but isn't working today, we have disconnected it and cleaned all visable places.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell Rug Cleaner Model 1695


I think you have the same problem as me, If you lay the handle down and remove the tank you'll see a vacuum hose that runs from about the middle of the machine back towards and up into the handle. that hose probably has a hole in it. which is my prob ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!


Call BISSELL Consumer Services.\015\0121-800-237-7691\015\012Mon-Fri: 8am to 10pm ET\015\012Sat: 9am to 8pm ET ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Water doesn't come out of my Bissel Deep Cleaner


When changing belts both must be changed at the same time because the pump belt will stretch out and will not run the pump right unless it is tight and the brush belt will break or slip so both must be changed together at the same time. this is how I ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 - On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 - not


Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I got a used bissel 1720-9 bissel cleaner..It holds water,,and turns on but no water comes out the nozzel?? what side of tank do i put the water in also there was no instructions,,there is suction when i turn it on but no water,,


You can download a user guide from www.bissell.com Just type your model number in the search panel ... Bissell 1720-1 Little Green Wet/Dry Vacuum

Water wont come out of my bissell proheat model 25a3


... Bissell Vacuums

I HAVE A BISSELL PROHEAT CARPET CLEANER I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Our bissell proheat carpet cleaner model 3750-T will not **** the water and cleaner through. Is there a schemetic available for free on this or a similar model


The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the w ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Is this free? i have a bissell carpet cleaner and i cannot get the soap and water to come out. it will **** up the dirty water however. i just found the belt is broken but i can see no way of how to put a new one in. is a broken belt the reason no soap is coming out?


If it is the flat belt that broke, that is the pump belt, the pump can't work without it. To replace the belts, turn the unit over, remove the red holder, has one screw, pull it out, then the brush roll will come loose. You can replace the belts th ... Bissell Powersteamer 1694 Upright Vacuum

I have an older model Bissell rug shampoo machine, model # 1631. I have several bottles of Bissell 5 One carpet formula to use in this machine, however I have lost the measuring bottle that tells me the amount of soap solution to use per 64 oz. bottle of water. I sure would appreciate if you could help me.


I have a older mod. Bissell carpet machine plus mod. 1630-5 and need a floor nozzle part num.013-6194 and grip tube w/button part num.014-4181 and trigger part num.010-9406 and tube ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My bissell powersteamer model 1695 does not spray enough water out. Hardly anything will come out of the handheld attachment either, just a few drips. With the floor unit, it appears the only water coming out is a result of gravity when the control is squeezed. Nothing appears to be plugged up with debrie or deposits. There does not appear to be any kind of drive belt for the pump as it seems to operate off the main vacuum motor. Any ideas?


Hi, my name is John I will do my best to assist you.\015\012\015\012Referring to this ... Bissell 1695 PowerSteamer Vacuum

Bissell proheat model 8910 water will not come


\015\012check pump belt\015\012seat tank properly \015\012check tank filteri have repaired many of these and found that 90% of the time its the pump! ... Bissell 8910 ProHeat Clear View Upright Vacuum

I own a Bissell Proheat Pet Model 8910. After just a few uses and changing both the brush and pump belts (trying to resolve problem) carpet doesn't get wet any longer. Carpet solution comes out normally but the water barly leaves the section of the tank I fill water into, resulting in carpet recieving to much solution and not enough water. Any advice?


... Bissell 8910 ProHeat Clear View Upright Vacuum

Water Leakage We have a Bissell Proheat (Pro Tech). I don't think it is the 2X model. When releasing the water with the knob on the handle, water comes out the side of the housing at the lower part of the unit. Is their a seal that my be worn out or broken. Can you give us some ideas before we take it to an expensive repair man to fix


Check the water bottle. Ours has been doing the same but putting a bit of j cloth between what they call the o ring and the cap fixed it. Really you need a new bottle assembly ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

No water I have a Bissell 1694 and it is not ejecting the water cleaner solution out of the front of the machine. The belts are ok. The two nozzels and hoses are not clogged and do not have any holes. I think the pump still works because water still comes out of the brush tool.


It is easy to take the top off. Mine has just 6 screws. Then you can see all the tubing and parts. For example, you can unclip the nozzles and see if water flows. Try blowing through the nozzle to see if it is plugged.\015\012\015\012Some people s ... Bissell Powersteamer 1694 Upright Vacuum

Bissell ProHeat 2X Select Upright Deep Cleaner not pumping water to floor. Water is not flowing out of the pouch area into the carpet. Water does not come out of the blater, I have checked the line & valve and they are clear how do I check the pump


Make sure you have soap in the soap container or the water will not pump. Sounds strange I know. Even if you have the soap mixture selector turned off, it seems that these machines won't pump clear water unless the soap resovior has fluid in it. D ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1157 seconds