Having problems with your Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum ?

No solution or water coming out...

\015 My bissell proheat x2 started not putting enough solution out just all water so i had a PET CLEAN UP JOB SO I JUST ADDED SOME SOLUTION TO MY WATER AND DID THE JOB NEXT THING I KNOW IM NOT EVEN GETTING WATER OUT OF IT!!!! ANY IDEAS ON WHAT TO DO NOW\015

Answers :

The water out let are pluged the machine sits dormant with soap in gravity pulls it down and the heat drys it. thus on h2o now to fix it turn up side down remove screws from bottem plate and belt assembly turn back over lay handle on floor remove scews from middle front and back use long blade screw driver remove cover with cellphone take pic of vac with cover off [ for reference on reassembly] water head located on the front of vac pull head and hose from seat wash with hottest water you can stand try to blow air through it with your mouth .with cover off put water tank in plug in vac careful not **** any thing up turn on vac try the water if no try pump check hose connector. To reassemble reverse steps using pic as refenece this should help later
Repair Help & Product Troubleshooting for Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!


Call BISSELL Consumer Services.\015\0121-800-237-7691\015\012Mon-Fri: 8am to 10pm ET\015\012Sat: 9am to 8pm ET ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

DIRTY WATER THE FRESH WATER AND SOLUTION COMES OUTON TO THE CARPET, BUT NO DIRTY WATER IS COMING INTO THE CANISTER.


Remove the dirty water tank and see if the front nozzle is fitted correctly, also see if the filter is clean on the dirty water tank ... Bissell 1770 Quicksteamer II Upright Vacuum

Bissell Powerease Lighweight Deep Cleaner. (Shampooer) After I fill the solution tank with the solution and water, I put it in it's slot, but all of the contents just come flowing out. I have only used this machine twice and it worked ok. You are supposed to press the trigger and the solution sprays out and then release the trigger when you want it to stop. But like I said, now I just put the tank on and all the contents come flowing out. I don't know what's wrong or how to stop it.


... Vacuums

I own a Bissell Proheat Pet Model 8910. After just a few uses and changing both the brush and pump belts (trying to resolve problem) carpet doesn't get wet any longer. Carpet solution comes out normally but the water barly leaves the section of the tank I fill water into, resulting in carpet recieving to much solution and not enough water. Any advice?


... Bissell 8910 ProHeat Clear View Upright Vacuum

Replaced the pump for a 9300 M Bissell Proheat 2x as the water solution was not releasing to the carpet. Once rehooked the lines the solution appears to be coming from the water tank and returning to the used tank and bypassing spraying on the carpet. How can I be sure the hoses are hooked up correctly?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a hoover steamvac dual v and is leaking, bristels not working very food only two are speaning and is not sucking any water Very little solution comes out, or comes out in streaks when pressing the solution dispenser button on the handle. I think the lines may be stopped upped.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=41020&thid=634728\015\012I have a Hoover SteamVac\015\012Posted by albazo on May 30, 2008\015\012I have a Hoover ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Water will not come out of cleaner, solution will but water won't


If you emove the solution tank youy will see a connector where the tank meets the connector.that is what lets the solution through ,its most likele cloggedlook and see if there are some holes in the connector and poke them with a paper clip.same goe ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No water I have a Bissell 1694 and it is not ejecting the water cleaner solution out of the front of the machine. The belts are ok. The two nozzels and hoses are not clogged and do not have any holes. I think the pump still works because water still comes out of the brush tool.


It is easy to take the top off. Mine has just 6 screws. Then you can see all the tubing and parts. For example, you can unclip the nozzles and see if water flows. Try blowing through the nozzle to see if it is plugged.\015\012\015\012Some people s ... Bissell Powersteamer 1694 Upright Vacuum

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

My bissell proheat is not sucking up water, the solution comes out but when I went to empty the water holder I only had about one fourth of the water that I had in their and the carpets feel very wet.


This is easy. remove the plastic top that snaps to the part that holds the water bladder. Instide that top piece is a red door... and behind that flapping door is an air filter.... remove all the crud stuck to it and you should be good to go. No t ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

No solution or water coming out...


The water out let are pluged the machine sits dormant with soap in gravity pulls it down and the heat drys it. thus on h2o now to fix it turn up side down remove screws from bottem plate and belt assembly turn back over lay handle on floor remove s ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My irobot scooba does not spray cleaning solution out after about the first 30 seconds it is running. I have tried all the suggestions in this post with the suction bulb to charge with air, and then with water to clean it out. water does come out of both valves when forced with the bulb or immediately after using the bulb to charge it. then after it runs for about 30 seconds the floor is dry.


... iRobot 5800 Scooba Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Model 8905...water or cleaner will not come out the bottom, only through the hand sprayer. Everything at the user level has been cleaned and the water and cleaning solutions are full. Nothing is going through the flow assembly. The selection switch is in the correct position


Hi, I checked through the troubleshooting for this model and came up with 2 possibilities. It could be that the tank is not seating well. If this is the case, trying putting a small amount of vegetable oil or vaseline on the seal. Please, ... Bissell 8910 ProHeat Clear View Upright Vacuum

I get no water coming through my bissell pro heat cleaner. thried all the listed solutions-still no water- help!


Advanced formula ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell proheat cleaner is letting out little spray solution when on the floor cleaner setting. If I press the sprayer on the attachment solution comes out of it even when it is not set on the attachment setting what should I do to fix i. How do I clean the water nozzles under the machine?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How do you use a bissell proheat. Where does the water go. Where soes the solution go. how do you get the water etc. to come out


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a Bissell steam shampoorer..I'm not sure where the water goes. I assume in the bladder (soap & water)..there is a little red plastic piece that I don't know where it goes..somewhere in the bladder?..Anyway, no solution is coming out and of course no vacumming up. Cannot find my manual or instructions. I've had it working before..thanks


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

No water comes out when you press the trigger only solution comes out when you turn it on its side


Check the belts. Most models have two belts. The first one from the motor runs both the brushes and the water pump. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Cleaning solution does not come out when I pull trigger.Also no water is coming out.What could the problem be?


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 8910 ProHeat Clear View Upright Vacuum

I cant get the water solution to come out of the tank


You must of put the tub on wrong. other wise it would be working fine ... Kirby Ultimate G Bagged Upright Vacuum

The solution comes out but not water. - Bissell 1699 ProHeat Clear View Upright Steam Vacuum


Did you mix the solution with water thats how they work it,take one cap full they gave you a messuring cup when you got the unit.I hope the solution goes in the same bag so retry the mixing and you should get water and soap ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The carpet cleaner comes on and the heat source is working in it, but the machine is not dispensing the water and cleaning solution. It does have consistant suction. What could cause this type of problem?


Most likely a bad belt you might think it looks good but i'd say thats your prob after you replace it you should be fine if not we can go deeper ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

The cleaning solution and water just keep coming out without touching the trigger.


If that condition is present when the unit is not turned on, or not plugged in, then the failure is a water control valve (solenoid), located in the base. It may be stuck open, or have debris blocking the seal internally. The valve itself is not us ... Hoover F7431-900 SteamVac Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0544 seconds