Having problems with your Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum ?

My Bissell Proheat left wheel cracked and I have a replacement wheel but can't figure out how to take it off. There seems to be no way to unscrew the bolt that is holding it on. Can you advise?


Answers :

I believe it just pops straight out. Carefully pry it straight out with a screwdriver. It should snap back in
Repair Help & Product Troubleshooting for Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bissell Proheat left wheel cracked and I have a replacement wheel but can't figure out how to take it off. There seems to be no way to unscrew the bolt that is holding it on. Can you advise?


I believe it just pops straight out. Carefully pry it straight out with a screwdriver. It should snap back in ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

This dyson dc15 is pulling to one side not sure what it could be, also the wheels at the back dont seem to be staying down the are flipping back up when trying to stand it up, can anybody advise what


Look at the guide ... Vacuums

I have a 5260D Baby Lock Serger, which I had tuned up a year ago. I haven't used it very much since. When I took it in, and again now, it sews fine for awhile, then starts slowing down until it is barely sewing, even with the foot all the way down. The hand wheel seems very tight. - it doesn't turn freely, but takes a some push, like it is resisting a bit. Any idea what could cause this slow down and the tight hand wheel? I appreciate any ideas. Thank you. Maura


Hi,Since you say that you didn't use it for many years then does it make noise?If so it need oiling on its parts.oil orifice and point of contact.Please do rate the solution if the issue is resolved or post a comme ... Vacuums

ShopVac pump The waterhose connection is up high. The only way to get the water up to the level of the hose is to continually hold down the on button due to the automatic shut off after it fills to a certain level. On the bottom of the filter there is a hole. I am thinking there should be a small hose of some sort to put into that hole that would then lead up to the level of the water hose. Concept makes sense to me. But in the meantime, good old duct tape seems to have done the trick. Not exact


Hey thats great whatever works its what makes america great ... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

How do you replace the belt? I took off the door and there seems to be no easy way to get it over the lower red wheel.


Take off belt cover on the left side of the top cover, turn cleaner over, take out screw from red lock and remove, pull cap and brush roll out, unhook the cogged belt, then you can replace the pump belt thru that opening. Put belt over the pump pull ... Vacuums

I am putting my bissel 8910 back together and behind the motor there is a black 3-way tubing connector. One side goes to the pump discharge, one side goes to a tubing going to the right rear wheel (facing the unit from the front) I don't know where the third side goes to. I do not seem to have another tubing for this one to go to? Maybe it is lost or ?


Hi, its hard to know what its for without seeing it. The best way to test this is to start the machine and vacuum a part of the carpet/ floor. Then let me know wht the vacuum is not doing. This will narrow it down. Please, get back to me. This sounds ... Bissell 8910 ProHeat Clear View Upright Vacuum

Bolt on wheel snapped and unable to fix as the end is in the hole. Is there a way to return the item and has it happened before?


There is a tool to remove broken bolts and screws at hard ware store, probably under $20 ... Dirt Devil Featherlite Deluxe Bagged Upright Vacuum

There seems to be a wheel that holds tension to the belt which came off. Now the belt spins and makes a grinding noise. I cant figure out how to get to the belt? Any one have advice?


I can help you a lot further if you can send me a picture of the bottom side of the vacuum. My email is [email protected] Once I see a picture this will help me tell you how to fix it. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi, I have a Dirt Devil Model # M08100REDC. I desperately need to change the bag, but I don't see an obvious way to do it. I'm afraid to try pulling on the cloth tab thingy that's just below the handle, between the rubber ring that holds the bag on the vac, because it seems like stuff will fly everywhere from the force required to remove it, and I might not be able to get it back on there. Should I just pull on that cloth tab until the bag comes off? Thanks, Roberta


You can pull on the tab to remove the bag, but probably a better way is to gently pull on the rubber ring that attaches the bag to the back of the vacuum body. If you don't yank and ****, it should come off without spilling the dirt. There may also b ... Dirt Devil Classic M08100 Bagged Handheld Vacuum

Mine is a much older Kenmore 840 which for years has only retracted the cord part-way. I expect there is dirt in the retrieval mechanism but can't get at it. HOW do you open this type of vacuum when it seems sealed all around and there are no nuts, bolts or screws visible?


... Kenmore Vacuums

How can I change the belt on the kirby vacuum shampooer brush roller. There is no way to snap the roller out and it seems that trying to unscrew the end isn't doing anything either.Model 5584 renovation group is what is written on the shampooer attachment. The kirby is a heritage model 2HD - purchased in the late 1980's.


... Kirby G6 Bagged Upright Vacuum

I bought a EURO-PRO hand vac SV772. I seem to have to hold the on button to keep it operating. Is this the way it is supposed to work?


... Vacuums

I own a Eureka Optima 437 and one of the rear wheels are broken and cannot find parts for this. Where can I find parts for real wheel? I have a rear wheel that came off too. The wheel seems fine, but the plastic base that the wheel clicks onto on the underside of the vac seems to have cracked. I need a new plastic bottom. Any ideas?


Called Eureka Customer Service and ordered another part. They are mailing it to me free of charge!No more problem. ... Eureka 431A Optima Bagless Upright Vacuum

Floor Attachment I took off my floor attachment, but now the belt seems to be off and I can't seem to get it back on right. I can't use the attachment and I don't know why it's so hard to figure this out. They say, just turn it to belt off, but when i turn it it lift's it up and can't line up with the belt off label. Then, when I turn it the other way, it's off. So I've been trying to pull it off so when it lines up with belt off, it's off. But the I turn it the other way and it's still off a


Try this,\015\012\015\012With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on t ... Kirby Generation 3 Bagged Upright Vacuum

I need to find a way to replace the attachment hose on this unit. the tube to spray the detergent snakes into the base next to the wheel and i'm unsure of how to take it apart without breaking it. is there a simple way to remove the wheel? do i need to do something special to replace that tube?


The best thing for that situation is to look on the side of the road and you will find a Bissel, I see one or two a week. Take one home and experiment on that one not yours. I have brought many and never have I bought one. I never see a Hoover by ... Bissell 9200 Upright Vacuum

I have a bissell proheat 2x and it leaks water around the wheel it holds dirty water but doesnt hold clean water.......and how do i remove the wheel on my bissell


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Floor tool wheel will not revolve on dyson dc08 origin vacuum - seems to be jammed. How do I disassemble the unit to fix the problem with the wheel. Everything seems to be clicked in. I do not want to force anything - I might just break it. Any help will be appreciated. Thanks.


Hi,The wheels on the floor tool get junked up with hair pretty quickly, at least they did for our Dyson. The metal peg that holds them in has grooved teeth to prevent it coming out easily, but it will come out if you get a claw hammer an ... Vacuums

Cant seem to get the green light going on vacuum head,hook seems to be wrong way when its should be hooking the band off its doing the opposite


1)First, you turn the square belt lifter on the front of the power nozzle until the red arrows line up (belt off)2)Remove the power head from the front of the machine. Now turn the belt lifter the other way and line the green arrows up ag ... Kirby Ultimate G Bagged Upright Vacuum

Replacement wheel I broke the wheel on my bissell upright model 3760 and need a replacement wheel and possibly an associated side molding. I can't seem to find replacement parts such as these- any suggestions?


The rear number is 2036627, there is no side casing, you would have to replace the whole back, which Bissell isn't making avaiable. But o get the wheel, you might try bissell.com and see if you can order direct, or try a local repair shop to see if ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have Necchi Lydia 544, inheretade, and don't know which way the needle is fixed! what side does the flat part of the needle face? Also, what are the two bobbin holders on behind the main body of the machine, and how do they work? And, how the hairy heck! do I thread it? finally, for now! How do I get the bobbin holder to ...a...hold the bobbin, and b...make it stay in the machine, ..well, it obviously attaches in one way only, and I cannot find that way!? Thanks, Yvonne.


Hi,Here are some websites with useful information on your machine:http://www.free-guitar-tablature.com/Lydia.html This one shows how to take the bobbin case out with pictures.http://www.youtube.com/watch?v=FbEMwLNzsG4 ... Vacuums

My dyson DC05 has been playing up for a while. The motorhead would start fine with green light on and after a few minutes would stop and light would go green. then the power would go on and off - seemed to only work when I had the handle a certain way. Now no power at all. is there a way that I can check if its the power in the handle section as thats the only way you can turn this machine on? Thanks in advance


As the wires that control the motorhead run all the way down the hose it is a break in the wires you will need to buy the hose assy sorry its not thesort of thing you strip down and repair  ... Dyson DC05 Bagless Canister Cyclonic Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums

How to replace wheel bracket on dirt devil. I have a dirt devil swivel glide and I took off the wheel bracket to clean out a clog and now I cant seem to get the wheel bracket back on.


... Dirt Devil SwivelGlide Bagged Upright Vacuum

Both of the wheels are wobbly and loose on my Kenmore upright vacuum model 721.37060. I don't see where I can remove them to analyze and fix the problem, which seems to be that the wheels are loose on their axels. How do I get the wheels off and what do you think I'll find inside?


Most if not all vacuums have an access panel on the bottom.It may be held on by a couple of big plastic clips,the kind you squeeze together and it releases a door.Some have plastic screws.There may also be a couple of phillips screws along with it or ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0418 seconds