Having problems with your Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum ?

The lights which tell you if you are going at the right speed on my Bissell PROHeat Pro-Tech have stopped working. Just wondering if this could be as simple as a bulb or more serious. Also, how do you remove the clear panel at the front for cleaning? Thanks


Answers :

The clear view window is unscrewed with a philips screw driver on either side of the nosel opening (top) but make certain the handle is layed back so as to alleviate twisting off the clear view cover. There are six (6) screws that hold the top cover to the base/motor compartment and you must also unscrew the clear plastic viewing window where the smaller spinner is inside so as to gain access to the hoses that go to the wheels that may have been disconnected or twisted internally that may be the cause of the lights not operating properly.
I have this same model and never noticed the lights telling me the "correct speed" learn something new everyday....
\015\012
\015\012the clear plastic hood removes with a few screws connected to the base at the bottom. the top part snaps out. :)
Repair Help & Product Troubleshooting for Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The lights which tell you if you are going at the right speed on my Bissell PROHeat Pro-Tech have stopped working. Just wondering if this could be as simple as a bulb or more serious. Also, how do you remove the clear panel at the front for cleaning? Thanks


The clear view window is unscrewed with a philips screw driver on either side of the nosel opening (top) but make certain the handle is layed back so as to alleviate twisting off the clear view cover. There are six (6) screws that hold the top cove ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Dyson vacuum I have a DC07 vaccuum. The problem I am having is that the front does not want to stay down as I vaccuum and I continuously have to keep stepping on the front to make it go back down to the floor. It seems as though there is either not enough weight in the front or possibly the unit just has to be broken in so that there is not so much resistance between the handle and the front of the vaccuum. Could there be something I did not remove or is this typical on these vaccuums?


There is some thing broken it is two plastic cogs they help the front go down and stay up you will have to get a star screw driver and there should be two screws on top and two at the b ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Sanitaire Commercial vacuum SC5815 A-2 does not turn on. It is quite new and seems to be "totally dead." Serial number: 0632005978 It is firmly plugged in, I have tried numerous electrical outlets, and I have tried the on-off switch numerous times. I wonder if there is a simple circuit breaker switch somewhere on the vacuum that I could switch without going to a repair shop? Or, I wonder if some latch is loose that shuts off the current, but I have checked the latches and they are clo


... Electrolux Sanitaire True HEPA Upright Commercial Vacuum Red EUKSC5713A

I have a Hampton Bay ceiling fan model #EC2T-36 HPF. We broke the globe that covers the light bulb when we were changing the bulb. Just wondering if you could tell me where I can buy a new globe cover?


... Vacuums

KIRBY MICROSWITCH I SUSPECT THE MICROSWITCH ON THE FRONT OF MY KIRBY IS FAULTY. I COULD GET THE MACHINE TO COME ON BY PRESSING THE SWITCH, NOW THE VACUUM DOES NOT COME ON AT ALL. CAN THIS SWITCH BE REMOVED OR CAN I OVERRIDE IT?


Http://ww.ebay.com/gds/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM-/10000000003752018/g.htm ... Kirby G4 Bagged Upright Vacuum

Have Fresh Aire 2.1 about 4 years was running great then went dead. I cant find where the fuse is and have unit apart. I plug in no fan dim display shows to errors. Unit was pretty dirty at the time. I need schematic and suggestions. Also need to knpw how to remove the honeycomb from the light unit to check for blown bulb. Seems brittle and I could break it with trying to pry with augur or sharp screwdiver object.


I'm sorry this may only be a partial help. But fuses are usually very close to the motor, OR where the switch is located. Pretty easy to find by testing but you have to be or so careful you dont electricute yourself. Now if your testing shows v ... Vacuums

Our vacuum model #6579-3 spits dirt and everything out the front and when trying to use the attachments we have cleaned and washed every removable part of the vacuum is there something else we could to fix it or is it permanently damaged??


... Bissell 6594 PowerForce Bagless Upright Vacuum

The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.


\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]


... Miele Vacuums

How do i remove the front of the Proheat Clearview to clean it out? I removed the two obvious screws at the front sides of the clear plastic part but see anything to remove to take it off.


... Bissell 1699N ProHeat Clear View Force Upright Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

Revolving brush at front of machine has stopped spinning, what could be wrong


Hi there, I'm sorry to hear you're having difficulties with your DC24. If the brush bar won't rotate, you may need to reset the machine - please follow the steps shown in the video below to do this. When pressing the red reset button, you may ... Dyson Ball DC24 Bagless Upright Vacuum

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

How do I install the front wheels on a kirby sentria G10D? One of the front wheels broke completely off so I ordered the front wheel shaft assy but I didn't remove the broken one so I am having difficulty with how to put the new one on.


... RTO Vacuums

I RECENTLY PURCHASED A HONEYWELL 2000i INVERTER GENERATOR AND I HAVE LOST THE USERS MANUAL SOMEWHERE IN THE HOLIDAY MESS. I AM LEAVING ON A TRIP IN A WEEK AND A HALF WHERE I WILL NEED THAT MANUAL. I'M NOT HAVING ANY LUCK FINDING ONE ONLINE AND WAS WONDERING IF YOU COULD DIRECT ME TO WHERE I COULD FIND ONE, OR SEND ME ONE. PLEASE! I WOULD APPRECIATE ANY ASSISTANCE. THANK YOU. .MICHAEL ALLISON [email protected]


You will need to contact Honeywell at this link below and fill in the form to request a free user manual for the Honeywell 2000i Inverter Generator:\015\012\015\012 ... Vacuums

I have a halogen light bulb with a frosted glass cover over it. How do I remove the cover to change the bulb?


... Vacuums

Hi I am wondering if someone could send me some (Schematics for a Bissell 9300-1) I took it all apart to clean out all the ( Hard watter out of the hoses) and now I cant remember where all the hoses go,I need to see where all the hoses go so I can hook up if someone could help me out! Thanks!!


Hi, you should be able to download the manual/manuals you need on the following web page. Just paste the following onto your search bar. I've used this site to find manuals before, it can be trusted. Good luck!\015\012http://www.manualsonline. ... Bissell Vacuums

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony


... Kenmore Vacuums

Telescopic duster hello, i was wondering how you remove the yellow telescopic duster from the side storage spot? It says it's a self-cleaning duster, but I can't seem to remove the duster from the container


Just pull straight up. They're a bit stubborn at first, but there's no real lock or anything in there, so trying to get it to release by twisting or pushing on anything won't help. (I know this because I spent quite some time not wanting to break a c ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

Passat 2000 W Reg Had the rear brakes and disks changed then a month later had a front tyre replaced and as I drove off something went tinkle tinkle on the road (like someone had left a spanner). Week later the ABS light and the brake light come on with the usual STOP Brake Fail Service Manual message. Had brakes checked but they could find no fault. I've tried the ABS under controlled conditions and it works. What could the problem be?? I've been running the car under these conditions and no pr


The ABS module has a history of wearing out on VWs. Nothing wrong with the brakes themselves, but the ABS module would need to be replaced to stop the lights coming on... but the problem is a new ABS module can be very expensive for a new one (~$900 ... Vacuums

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?


... Panasonic MC-V7515 Bagged Upright Vacuum

I have the yellow altima vac. for a while now I can not get the darn thing to pick up properly. Or should i say keep it up.. The vac does seem to be getting everything picked up but as soon as you turn it off, you have a mess under the vac.. I have checked for clogks and can't seem to find any.. I have removed the hose, Nothing there.. And yep have removed the yellow thing inside the trash cup.. Is there anything else you could suggest??


If it smells hot, then there's a strain on the motor no doubt about it. Check the suction channel behind the sole plate and remove all of the hoses to check for a clog. It could well be that there is a clog inside the machine after the dust channel f ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

We have a dirt devil cylinder vacuum cleaner with bag and when we plugged it in tonight it made a loud noise and a horrible smell came out of it. We could also see some blue sparks inside it. I was wondering of you could help?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=830037\015\012Generic problem for all Vacuums\015\012We have a dirt devil\015\012Posted by smilingreb o ... Vacuums

Have Hoover SteamVac Model F5835-900. Has gunk under the front clear hood where water/debris is lifted from carpet to the tank. Wife wants me to remove clear hood to clean; however the hood cannot come off without damage. Can I safely remove this hood?


There 2 screws on the bottom edge, one on each side, then there is a ***** on top at just beyond the lip of the window. Then it will come off of the machine. \015\012\015\012 ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0544 seconds