Having problems with your Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum ?

New replacement pump on Bissell ProHeat Protech not working

\015 My husband replaced the pump on the Bissell ProHeat Pro-tech 7920 model, but the water/solution won't flow. He's gone through all the tips from Bissell about seating the Tank-in-Tank and SmartMix tanks right. He's wondering if it's a priming problem. Or is the new pump defective?\015

Answers :

Made a mistake, my model # is bissel 7901. Won't spray water.\015\012When you turn the machine on, it sprays for a minute or so then stops. All belts are in place..water tanks and spray bottle positioned correctly.
Not sure if I have the same model but this is what I found on mine this morning - wire to switch in the handle came off. Un-plug power cord. Unscrew top two screws on upright handle and remove the front cover above the trigger. see if wires are connected. top connector is not used - if you do solution will spray all the time. Good luck!
Repair Help & Product Troubleshooting for Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

New replacement pump on Bissell ProHeat Protech not working


Made a mistake, my model # is bissel 7901. Won't spray water.\015\012When you turn the machine on, it sprays for a minute or so then stops. All belts are in place..water tanks and spray bottle positioned correctly. ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have Bissell ProHeat 2X 9300-M that I tried to use again today. Is does not dispense solution when turned to Floor Cleaning, when switched to Hose it seems to be working fine. Brushes and suction are working as well. Soap and water containers are full. I took off and replaced tanks, waited to prime the pump multiple times without success. Not sure what is going on.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have Bex Bissell Proheat. It is one problem requiring fixing each time I use it. Just had a new pump fitted as water not spraying out. Now the water is not being sucked up. For the money this has not been a good product. When it works it is good. But the constant issues each time it is used is frustrating.


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a bissell proheat and it won't release the water/shampoo. We have replaced the pump, and it still doesn't work. What can I do?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a broken pump belt on my bissell powersteamer proheat. The belt was just laying in there. I have a new one but no where in the manual does it tell you how to replace it and where! Help


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

Bissell proheat 1699....just replaced the pump belt and still not working.


Try taking all the hoses off one at a time and see if any are clogged. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell Proheat Clearview 8905 pump replacement


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissel proheater I have a Bissel proheater 7901. When you power on the spray works fine for 2-3 seconds then will not spray. Power off for 30 seconds and then repeats the same thing again when powered on. I'm thinking the pump is bad. Any other ideas?


Will water squirt out of the hose? If it does, then you could have a clogged heater, which is in the handle. Check the bottom of the tank, is the round seal on the valve that is on the tank bottom? If not, it has to be there. Another thing is the ... Vacuums

Bex bissell proheat protech model 7920-e is not suctioning water up, have had new parts- example new water holder,new dial for controlling wash options , also has been in for repair but dont think they knew what they were doing.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha


I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Vax 6131 water pump had stopped working on taking apart it had over heated and plastic casing had melted in one place,obtained new pump from buy spares which matched old part fitted and reasembled but pump does not run ,is there any internal fuses ? Or any thing else to replace


... VAX Appliances Vacuums

Bissell proheat 7920 replacement pump


Part number is 2107181, it will cost around $30. Most local shops shoul have this part or can order it for you. You could try bissell.com. ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have a Bissell 1623-1 Steam Cleaner. It will work good for about 2 minutes and then after that it will not dispense cleaning solution on floor or through the hand held wand.I have replaced both drive belts with no improvement. I have cleaned it and found no obstructions in hoses and spray nozzles, put back together and it still will not dispense. Is it possible the pump or solenoid is no working? Aaron


... Bissell 1623 Steam Cleaner

Machine will not pump out water. Brushes work, motor works, new belt, Just will not put out any water??? It is a Bissell Powersteamer,Clearview 4 row brush , dirtlifter.


IF you take the tank out of the base you will see a recepticle where the tank nipple fits into the base. There is a cross looking pattern in the recepticle. Take a pointy object and press down inside the cross area between the bars in the little pie ... Vacuums

How do you replace the pump on the bissell 7920 proheat pro-tech


It could be the pump, but try these othere things first, to replace the pump, you have to take the top cover off to get to it.\015\012Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Bissell proheat 1698 reassembly, smart mix piston, new pump?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My first proheat lasted four years so I bought a new one. After I used my Pro Heat for only the fourth time my first issue occured, the gear on the pump that runs the brushes came off, so I had the one from my old proheat, I just changed the gear spindle that is screwed to the pump and fixed that problem but now it will not pump water. That is why I bought a new proheat, I could not get the old one to pump even after a new pump and made sure all lines were not cloged.


Is your new machine a 2X or like the old style proheat? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

1698 HAS NO SPRAY, APPEAR PUMP does not work - Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum


Does water squirt out of the hose, if it does your heater may be clogged, otherwise it could be the pump, is the round seal on the bottom of the tank on the valve, if not it needs to be. Is the back edge separating from the base, is so this will rai ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Replaced the pump for a 9300 M Bissell Proheat 2x as the water solution was not releasing to the carpet. Once rehooked the lines the solution appears to be coming from the water tank and returning to the used tank and bypassing spraying on the carpet. How can I be sure the hoses are hooked up correctly?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I replaced pump and put back together now it wont release any soap// bissell proheat 7901


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Need a schematic to put Bissell Proheat 9200 back together after replacing new parts..


I don't know if the user manual will help, but you can try to download it from Bissell's site at\015\012http://www.b ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

Bissell 7950 ProHeat Self Propelled Carpet cleaner Replacement Pump Belt part 215-0628


Normally, there is a post sticking out of the retainer to remove it. If the post is broken off, then you will have to lift the black arm and wiggle it at the same time and the retainer will pop up so you can remove it. On the belt side, the retainer ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0991 seconds