Having problems with your Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum ?

Removing the top of the 7901-1 Bissell Proheat

\015 Need to replace the pump on the 7901-1 ProHeat. How do I remove the top without breaking anything\015

Answers :

Unscrew the cap for the flow indicator, remove the 6 screws, the top will come off. When you put the top back on, make sure the piston is hooked on the smart mix knob(underneath the top cover) set the smart mix valve in the wtaer only setting, then put the top back on. Turn the smart mix valve to make sure it is turning like it should, then re-install the 6 screws and the flow indicator parts. (don't over tighten the screws)
Repair Help & Product Troubleshooting for Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

Removing the top of the 7901-1 Bissell Proheat


Unscrew the cap for the flow indicator, remove the 6 screws, the top will come off. When you put the top back on, make sure the piston is hooked on the smart mix knob(underneath the top cover) set the smart mix valve in the wtaer only setting, then ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Bissell proheat pet brush removal - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hi I own a Bissell Proheat Powersteamer pro-tech with a turbobrush. I have been using "bissell multi-allergen removal formula for carpets and upholstery." I ran out of that last night. Today I went to walmart looking for more. Everything I found said "2x Ultra Concentrated Bissell multi-allergen." I'm confused on where to add the cleaner. I have a water tank and a separate soap tank. The instructions on this new cleaner bottle say to add 4 capfuls for the formula tank and dilute with hot tap wat


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

How do you install the 210-1128 Bissell carpet cleaner steamer brushroll on the Bissell ProHeat 8910? The prong on the replacement roller is larger in diameter than the one it is replacing. How do you open it up enough to remove the plastic piece that is attached to the steamer - the one with the belt??


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a bissell proheat 2x and it leaks water around the wheel it holds dirty water but doesnt hold clean water.......and how do i remove the wheel on my bissell


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell ProHeat Clearview Steam Cleaner - need steps to clean the clear input area. I have removed the four screws and need to know how to finish the removal of the clear plastic input area.


For the clear outer nozzle, there are 2 screws holding it in place. Remove those, then from the bottom lift it up. Sometimes the seal holds it really tight and you may have to carefully pry on the sides until it loosens up. Then when you put it ba ... Bissell Vacuums

The lights which tell you if you are going at the right speed on my Bissell PROHeat Pro-Tech have stopped working. Just wondering if this could be as simple as a bulb or more serious. Also, how do you remove the clear panel at the front for cleaning? Thanks


The clear view window is unscrewed with a philips screw driver on either side of the nosel opening (top) but make certain the handle is layed back so as to alleviate twisting off the clear view cover. There are six (6) screws that hold the top cove ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

How to remove brush from bissell proheat 25A3/64D9


... Vacuums

How to remove cover on main unit of Bissell proheat clearview carpet cleaner


... Bissell 8910 ProHeat Clear View Upright Vacuum

My Bissell proheat carpet steamer is not dispensing any liquid. The red spindle visible from top view is not spinning and the belts appear to be in tact. Can you tell me what's wrong?


Does liquit squirt out of hose, if it does, the heater inside the handle asm. may be clogged. If not, then is the pump belt ok, is the gasket on the bottom of the tank(on the vavle) on or is it sitting in the hole or missing? It needs to be on the ... Vacuums

I do not have a manuel on our Bissell Proheat Multi-surface 2X and would like to use it now to remove some water on the carpet.


Try this link below for a manual\015\012\015\012http://www.bissell.com/Products/c/UprightDeepCleaner/Category.aspx ... Vacuums

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

How do i take the clear veiw window off of my bissell proheat carpet cleaner to clean it? I've removed the 2 screws on either side but it still wont come off.


There are 2 screws at the lower front of the clear panel. Remove both of these then lift up the panel carefully and make sure that the rubber gasket at the top of the panel is not lost. This may take a little force if you have not done this before. A ... Bissell 8910 ProHeat Clear View Upright Vacuum

How do i remove the brush - Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum


At the bottom were the brush is there would be a cover plate remove the cover and then you will be able to get to it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Belt removal Bissel PowerSteam ProHeat


First take off the cover on the left side oif the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I have a Bissell proheat,clearview. no water,cleaner comes out, the red fan on top is not moving.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Mystery part Bissell 1699-P. I removed the top cover and a part came tumbling out (from the rear of the machine - towards the handle area). I have no idea were this part belongs. I have a schematic of the cleaner but I can not locate the part on it. I tried to copy and paste a picture of the part but that isn't working so I will attempt to discribe the part: There is nothing stampted on the part that I can see. It is plastic(white), 2" long, 3/16" in diamater. One end is U shaped (u-shape is 1/4


One question... you haven't mentioned that the vacuum doesn't work now... as hard as this is to accept... if it doesn't effect the function... forget about it.... i could very well have been something you vacuumed up along the way.\015\012 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The clip that connects the water base to the top of the suction area broke off..where can I get a replacement base (the part where you put the water in and has the bag where you also store the dirty water)? I have a Bissell proheat 2x


Here is the number for Bissell, they can tell you who to contact near you.\015\012Service Center Dept. Phone Number:(800) 457-1509Service Center Dept. Fax Number:(800) 517-9535Hours:M-F 8:0 ... Bissell Vacuums

How to remove and attach the brush on a bissell proheat powersteamer platinum ii


it's VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Empty all the water. Thoroughly rinse out both water container pieces. Unscrew the three clear plast ... Bissell Vacuums

7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum: I have a Bissell 7901-1. I need to replace the pum...


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell ProHeat 2X - I removed the clean water tank bladder and now I can't figure out how to attach the insert from the bottom of the tank so I can put it back together. Any ideas? Make sense? :)


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell Powersteamer Proheat 1698 has rusty motor fan


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0644 seconds