Having problems with your Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum ?

I cannot remember where all the tubes that carry the water go after taking it apart


Answers :

Please to to the web pages videos for troubleshooting and help: God bless you.
http://www.bissell.com/how-to-videos/
Repair Help & Product Troubleshooting for Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I cannot remember where all the tubes that carry the water go after taking it apart


Please to to the web pages videos for troubleshooting and help: God bless you.http://www.bissell.com/how-to-videos/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I can not get the water, normal heavy traffic selector reinstalled after taking unit apart, i replaced the pump, and now i cannot get it back together, there seems to be a special way it goes together, and i'm not finding it. Are there any videos, or pictures that show how it should go back together?


... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Upholstery attachment The nozzle doesn't spray properly, the water just pours out (not alot) instead of spraying. It also has very low suction. The upright part seems to be working fine. I cannot figure out how to take it apart so I can look for a clog, when I look into the hose I don't see anything.


May have a problem in the noozle asm on the hose. Hose part #90001335. \015\012 \015\012 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

Bissell PRO Heat Steam Cleaner is not dispensing the water. I took it apart and cannot find any obvious issue with it i.e loose tubes, connectors etc.


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Vacuums

Cable stuck in machine (sphera 20). How do I take apart to release cable please? I cannot see any visible screws to take the machine apart. Cable will not retract or come out of machine


... Bosch Vacuums

I have a Bissel proheat 7901 carpet cleaner and it is not sucking the water up. Normally when I clean the water gets sucked back up and I have to empty the dirty tank. Now no water is in the tank when I am done cleaning. Please help I cannot afford to take it to the shop.


I'm not sure if this will help but I had the same problem and was about ready to pull my hair out. I ended up taking the fill tank off and if you look inside where the red overflow flap is you will find a small screened opening. I found that mine w ... Vacuums

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse


By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

I have 1699-R Proheat carpet cleaner recently I was replacing the food pedal during the process some tubings that carry water/chemical got mixed to the point that one side instead of spraying chemical sprays only water from oneside the other side that is connected to the flow indicator cap is completely dry does not move at all. I am looking on line to see tubing diagram for model 1699-R


The instructions in this Repair Guide pertain to the Bissell PowerSteamer ProHeat (#1698)\015\012and the Bissell ProHeat ClearView(#1699). \015\012If your unit matches this model numbers then the repair guide plus diagrams for this unit is mentioned ... Vacuums

I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?


Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I


You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I need to find a way to replace the attachment hose on this unit. the tube to spray the detergent snakes into the base next to the wheel and i'm unsure of how to take it apart without breaking it. is there a simple way to remove the wheel? do i need to do something special to replace that tube?


The best thing for that situation is to look on the side of the road and you will find a Bissel, I see one or two a week. Take one home and experiment on that one not yours. I have brought many and never have I bought one. I never see a Hoover by ... Bissell 9200 Upright Vacuum

How to take apart shop-vac tubes


Twist and pull? Beat it like it owes you money? Heat the outer part? ... Shop Vac Vacuums

My hoover windtunnel u6323-930 has dust leaking into air when unit is on. i think it is in the housing I cannot see and I need ti know how to take apart to determine which part i need to order thanks David Macali


You will just have to start taking the base aprt until you can get the motor, Just remember how it was so you can put it back together correctly again. When you have the motor off, look at the fan chamber, you probably have a crack or hole in it. ... Hoover Vacuums

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?


You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????


Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

We have the bissell pro turbo with heater and we cannot get any suction for the water. took completely apart and couldnt find anything.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Looking for someone to instruct me on how to take apart my hoover steam vac so that I can check for clogging. It just stopped extracting water from the rug everything else sounds fine. The return holder is in place and has been checked many times. Any help?


First remove the dirty water tank then turn the unit on if your facing the front there is a duct on the right where the tank sets there should be a black seal around it if you have suction there then you will need to check the tank ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Extension arm The extension arm will not pull all the way up from the holder and I cannot use it - is there a way to take this apart - or something that can be done to fix it?


Hi,\015\012\015\012Try pulling wand up from hose with machine turned off.\015\012\015\012Or are you saying that the wand & handle wont uclip from the body of the machine ?\015\012\015\012 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a dirt devil featherlite bagless vacuum; model #088600. It has suction through the hose but not through the floor mode. I think there is a blockage in the hose area but cannot seem to take it apart enough to find it.


There are 3 screws 2 on the left side behind the hose and 1 on the right back by the wheel.that will take the cover off.if you need to get into the bottom there is a screw on the bottom plate in the area where it looks like the belt travels.is the br ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Bissell 7901-1 The soap doesn't mix with the water when I pull the trigger, I can see the soap isn't being used when I do the carpets. What can I do, have no problem taking this machine apart.


If the mix valve knob is turning smoothly, then most likely the cap and valve for the sop bottle is bad. Also make sure that the seal is on the cap at the bottom of the bottle and not sitting in the hole. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Knob I cannot open the knob to put water. I don't remember if it pulls up or you turn it around. please help!


The safety cap (knob) turns counter clockwise to open so you can put water in. Turn clockwise to close after filling. ... Eureka Enviro Steamer 310 Stick Vacuum

I HAVE A HOOVER VACCUM CLEANER MODEL U8172-900. i HAVE TAKEN IT APART AND CANNOT TAKE THE TOP COVER OFF TO CHANGE THE BELT. CAN YOU HELP ME?


This must be a Savvy, Take off the plate covering the brush roll, then take out 2 screws from the bottom, turn it over, remove the Hoover emblem, there is another ***** there. Then the top cover will come off. ... Vacuums

No suction i have been using mine for like a year or so. today i went to use it and then no suction. the water comes out but it wont **** it up. I haven't had any problems till now. I cleaned the little red filter but still nothing. I dont wanna take it apart with out knowing what im looking for.


I had exactly the same problem with my five-year old my Bissell 7920, and it's probably a broken pump belt.  See page 19 of your instruction manual for how to replace.  The Bissel ProHeat belt accessory pack costs $3.99 and you get a pump b ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0588 seconds