Having problems with your Bissell 8910 ProHeat Clear View Upright Vacuum ?

Floor nozzle window

\015 Can the nozzle be removed to be cleaned out; it's plugged up\015

Answers :

Remove the tank tip back there are 2 screws take them out you will have to tug on the lens some times they stick just make sure you tighten the screws good after
Repair Help & Product Troubleshooting for Bissell 8910 ProHeat Clear View Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cleaning under floor nozzle window


Make sure you removed the 2 screws closest to the front then lift up on the front end of the window sometimes its sticky but it will lift up. when putting it back on put the tabs on the back end in first then slip it down in the front , replace 2 scr ... Bissell 8910 ProHeat Clear View Upright Vacuum

Floor nozzle window


Remove the tank tip back there are 2 screws take them out you will have to tug on the lens some times they stick just make sure you tighten the screws good after ... Bissell 8910 ProHeat Clear View Upright Vacuum

How do I remove the floor nozzle window in bissell dirtlifter to clean out the scunge that is blocking the air suction?


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

How difficult is it to remove and reinstall the floor nozzle window on the 7901-1 pro heat cleaner. We loaned ours out and it was returned in foul condition. Thanks


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bex bissell powerwash de luxe removal of floor nozzle window to clean


... Bosch Vacuums

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T


... Rainbow E series Canister Wet/Dry Vacuum

Fllor nozzle window blockage


Take the 2 screws out near the front outside edges then just lift it off ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The heated solutions only sprays out to the floor in a 3 inch area. It takes a long time to clean the floor with only 3 inches available. Are there some nozzles somewhere on the machine that I need to clear out? If so, how do I access the nozzles?


There are two nozzles (either red or white) on the unit located behind brush. Use an old toothbrush to clean them off and that should resolve the spray issue. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have an electolux EL7001 canister vacuum. When I attach the large power nozzle....the one for the carpets not the small one for the floors...the nozzle is not powered unless I strap it on with duct tape. Is there some piece I can purchase that will secure the connection between the wand and the power nozzle head so that it is powered without the duct tape?thank you.


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Water will not spray from floor nozzle but will spray from upholstery nozzle--solenoid broken? Bissell proheat 2X--took apart water is to the solenoid but not past it


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissel ProHeat carpet shampooer is not spraying to the floor. I have checked the hoses best I can and they appear to be clear, no clogs. The nozzles don't looked clogged either. The above floor hose does spray water. I definitely have not gotten my money's worth from this machine. Any solutions?


... Bissell 9200 Upright Vacuum

I've just purchased a Bosch BX1 1600 vacuum cleaner in Spain, and already I've lost the hard furnishing brush, the crevice nozzle, the upholstery nozzle, and the hard-floor brush that I think were in the box. Is there a place to purchase these separately? Thanks, Dave Wass


Hi Dave,Are you in the USA? If you are, try this web address: >>>> http://www.bosch-eshop.com/eshop/bosch/us/brushesfloortools.htm Copy and paste the address into your browser and the tool page will open up for you.Should you ... Bosch Vacuums

I have a signature 2000 ac window unit (10,000 BTU). Recently, water begin to slowly drip from the bottom right of the unit. I heard it hitting my floor. I took the front panel off and saw water build up. The unit is mounted in the window perfectly. How do I remove the water? I live on the 2nd story of my apartment building.


... Vacuums

Rug and floor nozzle brush not moving


What I had to do was take apart the vacuum head...which is very confusing, and the manual doesn't tell you how...the "secret" is to use a flat screwdriver to pop out the little wheels...there are two other screws "hidden" beneath them. Be careful as ... Hoover S2220 Flair Bagless Upright Vacuum

BISSELL 1699 :WATER PUMPS THRU HOSE BUT NOT TO FLOOR NOZZLES


Did you blew thru the heater with both hoses off of it? If you did and it was clear, could be the pump, it is just working weakly. Is the top cover flush with the base in the back? If it has broken loose and has risen up, then it won't work. Here ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Lost screw to front floor nozzle.


Go to http://www.bissell.com/Product_Search.aspx?Criteria=9500+pro-heat and click on parts & accessories. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell proheat cleaner is letting out little spray solution when on the floor cleaner setting. If I press the sprayer on the attachment solution comes out of it even when it is not set on the attachment setting what should I do to fix i. How do I clean the water nozzles under the machine?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I need a nozzle adjustment lever and cam kit for a Hoover upright U5432-900. This the part that adjusts the front wheels for different types of flooring.


... Hoover U5432-900 WindTunnel Plus Bagged Upright Vacuum

I have a Bissell Proheat Turbo 2x model 9300. It has stopped spraying at the floor. The hand tools will work so I assume this means the problem is at the base somewhere. I cleaned the nozzles but don't know what to try next. It has always had a problem with dumping too much cleaning solution as well, don't know if this is a contributing factor


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have an old Progressive vacuum cleaner that says "Hepa Filter" and "Whisper Belt". Not sure what the model # is. The problem is that the vacuum part itself (the part that touches the floor and rolls over) has ejected its filter that we can see through the little window- it just came out under the rollers under the device... we cannot see how to re-insert this piece of filter which looks like a kind of round, flat grey foam/fabric and clearly goes inside- (top of the part that touches the flo


Check this procedure:\015\012\015\012Unplug the appliance that you will be \015\012changing the filter in.\015\012\011\011\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\011\011\015\ ... Kenmore 23313 Whispertone Bagged Canister Vacuum

X1.1 model has plenty of suction through the nozzle, but doesn't 'pull' across the floor anymore or pickup dirt when using upright


Assuming that the automatic height adjuster is working properly, most likely your Sebo needs a new brush roll because the bristles on the old one are worn to the limit. To test the height adjuster, put the machine in the normal operating position (wi ... Sebo Automatic X1 Bagged Upright Vacuum

Does anyone know if i can get a replacement floor nozzle for my eletrolux z8220


Yes we have it. Call Sawtooth Vacuum. 12087332504 ... Electrolux Centralux Vacuum

My vacuum doesnt **** dirt from the floor but sucks dirt with the nozzle.


Probably have a clogged intake from the beater bar thru to the vac system.. Try this.. with the vac unplugged, flip the vac over so you can get to the bottom of the vac head near where the brush rotates.. then depending on the model.. remove the cove ... Eureka Vacuums

Water wont come out when handle pressed to do floor or out of nozzle for upholstery cleaning smells hot when trying to get it to work could this be a belt


Yes it most likely is the belt ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0244 seconds