Having problems with your Bissell 8910 ProHeat Clear View Upright Vacuum ?

Won't spray. . .nothing happens when pull trigger. . .pump belt is ok. ..

\015 Checked out the troubleshooting on the Bissell.com site and it didn't solve it. no obvious broken parts. seems to have "lost its prime" on the pump but turning it off for a minute doesn't solve the problem.\015\012\015\012Not spraying either when we try the handheld attachment. Seems to be a related problem. I've wondered if the portable bucket is seating tightly enough to draw water out of the bucket valve\015

Answers :

I assume you've changed the flat belt and it's working o.k. So, the next thing to check is the bucket seat. When the bucket is set down into the machine, the bucket valve is opened by the center pin on the receiver in the floor of the machine. You should put clean water into the bucket and install it. Wait a couple of seconds and remove it. Inspect the receiver and see if there is any water in it. If not, check the valve in the bucket and make sure that the rubber seal is in place. Sometimes they come off and stay stuck in the receiver. This will not allow the valve to open. If the seal is stuck in the receiver, remove it and re-install it on the bucket valve and test again.
\015\012By the way, if there is no shampoo in the shampoo tank, and the mixture dial is set anywhere but off, the machine will not spray. The pump will suck air through the empty tank and will not pick up water from the main tank.
\015\012If there is water in the receiver after you remove the bucket, then the problem is likely in the heater. The heater is located in the center of the handle and you must open the handle by removing the hose storage rack and then the top of the handle. There are two screws behind the hose holder that are at the back/bottom of the handle and are recessed into the handle. Once the handle is open, the heater is obvious. You will find two clear hoses attached and they often become plugged at the connections, just inside the heater. You can clear this with a 1/8" drill bit. Remove the hoses and take the bit in you hand and gently insert and rotate. Once cleared, replace the hoses and reassemble. I hope this helps. Be careful. These machines are a maze of hoses and valves and can be difficult to reassemble. Be very observant whenever taking one apart.
\015\012One more thing. I have seen instances where the screws that hold down the hood in the area of the tank have broken through the plastic and will lift enough that the tank will not sit down far enough to allow the valve to open. Check here, too.
\015\012I hope this helps.
Had somewhat the same problem.... I had water comming out but the solution was not comming out.... I called bissell and the woman talked me through it.... first put in water only mode,,,,, then Fill water tank with fresh water and put back in place,,,, then remove soap dispenser put to the side,,,, now , power on your cleaner,,,, for the next steps, do this exactly as I tell you >>>>>>hold down the trigger that releases soap the whole time you do the following>>>>>> switch between water only and heavy traffic four times,,,, all while while holding the trigger, then still holding the trigger, stop on high traffic the fourth time, leave it there,,, now put the soap bottle back in,,,,, still holding the trigger and hold the trigger down for exactly one minute after you replace soap bottle,,,, you should start seeing the soap come out........ (make sure its on floor cleaning and not TOOLS) Hope this helps and if it does,,,, give these instructions to someone else in this help area.........
Repair Help & Product Troubleshooting for Bissell 8910 ProHeat Clear View Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Won't spray. . .nothing happens when pull trigger. . .pump belt is ok. ..


I assume you've changed the flat belt and it's working o.k. So, the next thing to check is the bucket seat. When the bucket is set down into the machine, the bucket valve is opened by the center pin on the receiver in the floor of the machine. You sh ... Bissell 8910 ProHeat Clear View Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My Bissell model 8910 pro heat will pump solution or water for like the first couple times you pull the trigger as you can see the mixture window spinning. After that it stops spinning and nothing else will come out until you turn the machine off, and restart. Then again same process works for a couple trigger pulls then quits.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Producing steam i just got the shark assembled the mv2010, then it is not doing anything, it vacuumed just fine, but when i put the steam pad on it wouldnt ever produce steam or do anything,it felt like the water was heating up but even after it sat for 20-30 minutes when i pull handle back towards me nothing happens, no lights no steam no nothing, so why wont it work


This link is for the manualhttp://www.sharkclean.com/manual/MV2010_11_IB_ENG_110103.pdf ... Shark MV2010 Vac-Then-Steam 2-in-1 Vacuum and Steam Mop Purple

I just put a new turbine on my steam cvleaner hoover of coarse, and when I pull the trigger in wash nothing happens. In rinse it's all right


When you squeeze the trigger a cable is pulled which opens a small valve in the dispenser tank. Remove the tank and detach the valve. Soak the valve in clean warm water for an hour or 2 and reassemble. That should fix the problem. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a dyson dc16 and when i pull the trigger all three lights come on but nothing happens from that point?


It needs charging . and if the lights dont light when you put it in the charger somthing is wrong with charger or battery ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

My bissell will spray out of the hose, but no water or soap when i squeeze the trigger? The belt is turning the pump


See if your tank is seating properly. I bet it's sitting up a bit. Is there water in the little well where it sets? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My bissell powersteamer model 1695 does not spray enough water out. Hardly anything will come out of the handheld attachment either, just a few drips. With the floor unit, it appears the only water coming out is a result of gravity when the control is squeezed. Nothing appears to be plugged up with debrie or deposits. There does not appear to be any kind of drive belt for the pump as it seems to operate off the main vacuum motor. Any ideas?


Hi, my name is John I will do my best to assist you.\015\012\015\012Referring to this ... Bissell 1695 PowerSteamer Vacuum

Nothing spraying out of Bissell Powersteamer Proheat. I've check filter under flow indicator, pump belt is fine, cleaner in proper tank, bladder of water tank is full. We've had it for a very long time but it's barely been used. Can anyone help?


... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

Hey there, a friend of mine has a bissell pro heat 2x turbo, that is spraying no water on the floor setting, the pump works i assume, as the machine vibrates when the trigger is pulled, how would i troubleshoot this problem.


Check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- Check for deb ... Bissell Vacuums

When i pull the trigger to spray solution onto the carpet nothing comes out. But it does work when i use the spot treat attachment.


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

It will empty the cleaner but will not spray water filter is clean spray heads were taken off & i could blow threw them is it a case of no prime in pump if so should i fill pump i had this thing all apart and i now know evry inch of this matchine when i pull the triger it sometimes will spray for a sec.but thats it i also took the switch out and air goes threw when i press the switch if it is the prime in the pump how can i fill the pump . what hose on the pump will prime i thankx for your advic


The problem is most likely that your pump belt is worn, stretched or broken. Here you can get the belts you need and view the manual:htt ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Wont spray i have a bissell pro steam 2x and it wont spray the water out, i have cleaned everything and nothing seems to be working ...please help


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

I have a proheat 2x, and the pump will only spray water for a few seconds when unit is turned on, then nothing. The attachment is the same way. I think this is the pump failing, and the unit is only over a year old. How much would a pump cost? If this is the problem.


I just had my pump replaced for $66 and the repairman said this unit is notorious for this problem. He had 6 other units in his shop when we came in. Make sure you keep your clean water tank FULL, as he said the pump fails as soon as it runs dry. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The tool attachment for the hose on my Bissell ProHeat 2X CleanShot won't spray soap or water. The bristles on the tool rotate without a problem and the suction is working fine, it just won't spray water when I pull the little gray trigger on the tool.


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please


... Vacuums

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

Shampooer I have a rainbow e series and my shampooer is not working. The tubes do not seem to be clogged and it sounds like it is trying to work but we cant get the water to come out. We pull the trigger and nothing no soap, no water, nothing. Can anyone help?


Aqua mates have an o-ringed valve assembly that go bad regularly reccoment having it replaced by local vac shop ... Rainbow E series Canister Wet/Dry Vacuum

Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc


Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have a Eureka Contour model 2900 type A upright vacuum, the roller works fine nothing clogged, took it apart motor blade is free of debris, no suction from tube and blasts OUT air from the front HEPA filter location. New bag, New belt, nothing in hose.any clues as to why this can be happenning? Air should not be blasting out of the HEPA filter.


Even with your explanation,it seems the hose is clogged.Try taking the hose off,then blow through it or pour water through it.If this doesn't do it,make sure the suction canals are going to the proper areas. ... Eureka 2900A / 2901A Contour Bagged Upright Vacuum

Bissell 8920 wont spray any water/ solution except when in water


It sounds like you have a clogged line, if your mechanically inclined you can fix this yourself by tearing the unit apart. If you open the unit up, disconnect the lines on your pump and blow an air compressor through them. certain lines require you ... Bissell 8910 ProHeat Clear View Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0625 seconds