Having problems with your Bissell 8910 ProHeat Clear View Upright Vacuum ?

The smart mix bottle is not dispensing any fluid. I have been using this Bissell 8910 for 6 years. The cap and seal seem to have all the parts. thanks -LaRie-

Answers :

Repair Help & Product Troubleshooting for Bissell 8910 ProHeat Clear View Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The smart mix bottle is not dispensing any fluid. I have been using this Bissell 8910 for 6 years. The cap and seal seem to have all the parts. thanks -LaRie-

... Bissell 8910 ProHeat Clear View Upright Vacuum

Our Bissell Cleanview II 3576M does a great job except that the filter cup below the dirt cup gets full very fast and the dirt cup barely has anything in it. To clean the whole house, I have to empty the dirt cup and clean the filter several times. It didn't use to work this way. It seems like something is missing, a gasket or seal maybe? I don't think dirt, hair and debris should be going straight to the lower cup and bypassing the upper. I looked at the user guide but can't see why it's happen

Contact Bissell Direct for a parts diagram and support at \015\012\015\012http://uk.bissell.com/EmailUs.aspx\015\012 ... Bissell 3576 CleanView II Bagless Upright Vacuum

I have a Bissell Proheat 2x Model 9200. The solution goes directly through to the carpet. The tank empties extremely fast even when I am not pushing the button. I have also noticed that I have soap spots on the carpet when pushing the cleaner forward. These spots are not even associated with the cleaning mechanism. I have inspected the cap on the tank, but it seems to be OK. Any suggestions?

Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9200 Upright Vacuum

My vax rapide xl v027 leaks water from the clean tank through the rubber seal at the bottom of the tank. Seal seems ok but seems to rely on gravity. Leak is there weather or not its turned on

... Vacuums

My Bissel Proheat smartmix bottle is emptying really fast and it doesn't seem like the carpet is even getting wet. I am just trying to do a rug in the kitchen and have filled the smartmix bottle 3x now and the rug is barely wet yet. I have cleaned out the flow indicator filter and it does not spin when I push the button like it used to. I have also checked the belt and it seems fine. It is actually a Bissel Proheat 7901/8910 (Pet) but they could not find my product. Any suggestions, I am

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hi I own a Bissell Proheat Powersteamer pro-tech with a turbobrush. I have been using "bissell multi-allergen removal formula for carpets and upholstery." I ran out of that last night. Today I went to walmart looking for more. Everything I found said "2x Ultra Concentrated Bissell multi-allergen." I'm confused on where to add the cleaner. I have a water tank and a separate soap tank. The instructions on this new cleaner bottle say to add 4 capfuls for the formula tank and dilute with hot tap wat

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Nobody seems to be able to answer the question on how to change the belt on a bissell steam cleaner ..... Bissell is horrible for never giving customers proper instruction manuels .... THUMBS DOWN FOR BISSELL

I have the same prob. this is what i found\015\012\015\012\015\012Since changing the belt is the easiest fix, we suggest you check that first. (Before attempting any repair be sure your machine is unplugged from the electrical ou ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I bought a used vacuum seal machine (hobart model ht-120) it does excellent vacuum but it doesnt seal correctly all the time. it seems like there is something wrong with the valve that activates the bar that goes up and makes pressure and heats the bag for complete sealing. The heating is perfect but what is not working is what make the bar go up and down.

... Vacuums

My Bissell BS3920F upright (similar to the 10N6F) has been working wonderfully for the past 3 years but suddenly seems to not pick up dog hair as well as it used to. It has been pulled apart by my husband to ensure nothing is blocking the hoses etc and when running the suction seems to be there. It seems to grab the dog hair and leave it in a straight line directly under the unit without picking it up. I then disconnect the hose and use to hose to pick up the dog hair. This works well but obviou

Check to see if your brush is not worn down, they do wear with age - compare the length of the bristles with a new one. Replace the brush ir there is a significant difference in bristle lengths. Also check the flexible ben ... Bissell Vacuums

Bissell SpotBot model 7887 still seems to clean ok, but there is no wastewater appearing in its tank on normal "Fresh Stain" and "Set-in Stain" settings. Seems to work on the "Manual" brush setting though.

... Bissell SpotBot Robotic Wet/Dry Vacuum

My old bissell 3510 upright vacuum seems to have no suction into the bag...I replaced a broken belt several days ago, and now the vacuum picks up debris, but seems to just collect it behind a wheel..The bag does not "puff out" like it used to...How can I fix this??

... Bissell 3510 PowerPartner Upright Vacuum

The water tank on my bissell proheat 2x is not keeping the clean and dirty water separate. I;ve checked the container and there doesn't seem to have anything wrong with it. Also when I switch the machine on you can see the "washing" action, after a few minutes this seems to stop - there is water and forumula in the machine. Only had it a year!

... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The Height Adjustment mechanism is broken on my Bissell 6594 and I can't seem to locate a replacement. I have already checked the Bissell website is there another option?

You could google it... ... Bissell 6594 PowerForce Bagless Upright Vacuum

Keurig b200 problem; When brewing with cup in unit water will pass into cup and it seems when k cup is full the grinds puch up through the top and water overflows. i pulled out the k cup holder and cleaned so their is nothing that is obstructed included the piercing pin. brewed [product does come through but does not seem to allow it to come through fast enough or if it supposed to be pressurized it is losing its seal on the top of the k cup

... Vacuums

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?

... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

Can't reassemble!!! Long story as short as possible- I removed the hood from my Bissell 1699 and can't seem to get it back on correctly. The "Smart Mix" knob and it's parts seems to be the problem. How does this line-up, or what is the best way to put it all back together? Thanks, Josh

The piston is put on the bottom of the smart mix knob, turn the knob to the water only setting, then put the top housing back in place making sure that the piston went into the slot, after the top is all of the way down, turn the knob, if it turns ea ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My bissell pro heat 2X has stopped dispensing water from the tank, the suction is working and it seems to be dispensing the detergent, so it is not rinsing or washing with water. I have cheaked to see if there is a blockage but that doesn't seem to be the problem...please help

I have a Proheat 2X and had the same problem. I tried the Water Rinse setting and found water came out and was suctioned properly, but on the Light Clean, Normal Clean, and Heavy Traffic settings, the unit failed to do anything. Problem may be with l ... Vacuums


Please check the following: \015\012 \015\012First check the motor duct gasket. The motor duct gasket is visible once the tank is removed. It is located underneath the handle on the top of the base of the machine. It has a black rubber co ... Bissell 9200 Upright Vacuum

Again, I have a Bissel Model 3760-4. The same problem as everyone else. The beater bar will not turn. Took apart, nothing. Took to vacuum repair shop and they said it is not getting power to the motor to the beater bar. Seems like a fair number of folks are having this same issue. You would think Bissell would come up with a fix, if nothing else to save their reputation. Thanks Diane

... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

I have Bissell Model 1699-R Proheat carpet steam cleaner one of the tubings that connects into spray got mixed with some tubings during tubing replacment to the point that tubing that is conected into flow indicator cap does not turn at all to show if the chemical is sprying or not.i am looking mainly for tubing water/chemical diagram in order to verify the right connection.please help if you can bissell user. thanks

... Vacuums

Bissell Quicksteamer I have a Bissell Quicksteamer that is about 5 years old. I went to use it today and hardly any solution was coming out. I could see it suctioning up what little came out, so I took it apart and cleaned it thoroughly. I tried to use again and no solution is coming out. Everything seems to being working just fine. Thanks

Here's a kinda kick yourself quick fix that might be helpful, I took my whole machine apart all the way to the motor to come to realize that the small rubber piece that cover the tip of the water container was jammed in the hole you sli ... Bissell 1770 Quicksteamer II Upright Vacuum

My Bissell doesn't seem to be vaccumming as well as it was before. Not sure what the issue is. Could the belts be loose? They are on there, but not extremely tight. Should they be tight? The brush on the bottom seems to have a lot of play/bounce to it as well. Thanks for the help.

You have a partial or complete clog of the hose that carriesthe drit from the floor to the bag or other storage device.\015\012\015\012Clean it and you will regain the power you originally purchased. You may have to remove some parts to ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My Bissell 9200 is not sucking the water into the dirty water resevoir. 1. The gasket on the clear-view seems fine. 2. The suction power just doesn't seem powerful enough (feeling with my hand). 3. The brushes turn fine and belt is fine (not sure if that even matters for this issue). Any help appreciated. Thanks, - Matt

Disassemble all lines and check to see if all O rings are installed. If cracked missing or stretched out of shape no suction will be provided ... Bissell 9200 Upright Vacuum

Bissell 7700 series, pro heat all rounder. Won't spray water. Have checked the line from the unit to the spray nozzel and all seems clear. Water doesn't seem to be flowing from the tank to the end of the unit where the hose connects into. What could be the problem? Any assistance would be greatly appreciated. Thank You. Steve

HelloGrasp the cleaning solution tank, and remove it from the machine. Reinsert the tank into the machine, making sure it fits snugly in the machine. If the tank is even slightly dislodged, water cannot get into the machine. Visually insp ... Vacuums

I just used my Bissell Proheat, when I heard the vacuum sound get lower and lower then suddenly something "gave" and it got very loud and started emitting a burnt rubber smell. It still worked to put liquid into the carpet; seemed to have trouble getting it out. I checked the tank, filters, belt, and roller and all seemed OK - but when I started up again and looked down I saw sparks in the motor/belt area and shut it down immediately. Any thoughts?

The bearing that is located at the top of the vacuum motor has failed . Because of that the shaft of the motor's rotor is out of position and the pulley attached to it has started rubbing on the other pulleys, giving you that smell. the spark appear ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0845 seconds