Having problems with your Bissell 8910 ProHeat Clear View Upright Vacuum ?

My carpet cleaner bissell pro heat wont extract the water from the carpet


Answers :

1) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Nozzle gasket (at the top of the Floor Nozzle window) and behind the SmartMix Bottle. If you feel vacuum-like suction at this area, your suction power of the unit is working but air is escaping at some point. If there is no suction at the motor intake valve your machine will need to be inspected by an Authorized Service Center Technician.
\012

2) It is possible the Floor Nozzle on your machine is inserted incorrectly. This would directly affect the suction of your machine. Please follow the directions below for removing and replacing the nozzle.
\012

Before starting, please be sure the machine is unplugged and the machine handle is reclined.
\012

To remove the Floor Nozzle window, first detach the Phillips head screws located at the base of the nozzle. Then, remove the Tank-in-Tank Assembly. Next, pull forward at the top of the Floor Nozzle window to release the tabs of this window from the receiving holes of the machine. This window is designed to allow access for cleaning.
\012

When replacing the Floor Nozzle window, please be sure the tabs at the TOP of the nozzle are properly inserted into the receiving holes provided. If you do not have the tabs in place properly, the suction power of the machine could be affected.
\012

Rotate the window down into place and replace the screws.
\012

3) Ensure that the Ready Tools knob (diverter knob) is in the proper setting and the valve opens and closes freely. Ensure the black foam gasket is in place under the valve.
\012

4) Check to ensure the Tank-in-Tank assembly is seated properly and that it is not full of dirty water. (If this tank has a drain cap, make sure it is in place and that it has a black o-ring).
\012

5) Check the float and baffle to ensure they are properly installed on the Tank-in-Tank. The larger square portion of this part should be below the clear baffle of the tank with the red flag portion of the float resting on top of the baffle.
\012

6) Check the Tank-in-Tank and lid for damage. Is the lint screen clogged? Make sure the lint screen is in place on the tank lid and not placed into the motor duct. Also, clear the holes on the lint screen.
\012

7) Check to see if the upholstery hose has suction. If the hose has suction and the floor nozzle does not, check the diverter valve to see if it opens and closes freely. This can be seen through the Floor Nozzle window as you switch the diverter knob from the floor to tools setting.
\012


\012

If these suggestions do not solve the problem, please have a technician at a local BISSELL Authorized Service Center inspect your machine. BISSELL supports your machine with a one-year warranty for any defective or malfunctioning part.
\012

Repair Help & Product Troubleshooting for Bissell 8910 ProHeat Clear View Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My carpet cleaner bissell pro heat wont extract the water from the carpet


1) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Nozzle gasket (at the top of the Floor Nozzle window) and behind the SmartMix Bottle. If you feel vacuum-like suction at t ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a Bissell pro heat carpet cleaner, the water spray wont come out to clean the carpet.


Bissel proheat turbo 2x ipx4.\015\012\015\012I don't have the instruction the this machine if you could help me with where to put the water and cleaning solution and how much, also how to use it.\015\012\015\012Thankyou, ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

My bissell pro heat 2x does not **** up the water from either the upholstery cleaner or carpet cleaner. Any thoughts as to why? The water and heat functions work it just does not pick up


First check the motor duct gasket. The motor duct gasket is visible once the tank is removed. It is located underneath the handle on the top of the base of the machine. It has a black rubber coating around it. If there is no suction there please let ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell pro heat steam carpet cleaner, not releasing water.


That means that you need to replace the pump belt. Here is the belt you \012need and a manual you can view:\012\012Bissell 7901 Belt and ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell pro heat will not extract water from the carpet


Try checking the top section of the machine (where the dial is located to switch it from floor to tool) and there is a little red plastic piece about 1 inch square on the inside of it. This is a lint filter that has a little door on it. Open the do ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell proheat carpet cleaner wont dump water or solution. It will however **** up water and solution if dumped on the carpet. Help I cant clean up doggie pee and it smells in this heat!


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Pro hEat will not **** up water from carpet - Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum


Check the vac motor hose could be clogged? does the vacuum motor turn on? check the vac motor on switch for power using an ohms meter.could have a bad vacuum motor or micro switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

When I clean my carpets and hold the trigger only water comes out, there is no soap leaving the container . I have a Bissell pro heat 2X carpet cleaner.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissel pro heat 2x wont spray any water - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


I had the exact same problem with my ProHeat 2. It would spray only through the hose attachment but not on the floor. Cleaning of the spray endings on the floor unit fixed my problem. Either soap deposits or dirt was clogging the spray endings. Here ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bought a Bissell Pro heat 12 amp cleaner and cant find manual. Forget how to use, carpet cleaner , water etc.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I need a manual for the bissell pro heat carpet cleaner #7091H. I used it but I can not get it to **** the dirty water out of the carpet. What am I doing wrong?


Try here:\015\012\015\012http://www.bissell.com/Product_Search.aspx?Criteria=pro+heat+carpet+cleaner\015\012 ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell Carpet Cleaner pro heat- water doesnt come out


The screw that is located in the center of the handle, that holds the assecory hose holder must be tight. My screw was missing, put one in and cured the problem. Sounds stupid but it worked. Got this idea off the Bissell web site. Also if you have a ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Bissell pro heat steam carpet cleaner is not releasing water


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Whare does the dirty water go in the bissel 12 amp pro heat carpet cleaner


The dirty water goes into a separate compartment in the solution tank that holds the clean water. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My Carpet cleaner, Bissell pro heat will release the water but will not **** it back into the the bas. Whats wrong with it


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissel pro heat 2 carpet cleaner will not suction water and brushes won't engage


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Mi bissell carpet cleaner pro heat 2 is not sucking up the dirty water any body any idears


Clean lower part of cleaner ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Bissell Pro Heat 2x carpet cleaner water tank valve is messed up. All the parts are there, spring, metal ring, rubber bushing and pin. How are they supposed to go back together?


Here is a picture, maybe it will help, part #2036675, which is #7.\015\012\015\012 ... Vacuums

I have a Bissell Pro Heat 2X carpet cleaner, and it won't dispense the water and soap. It's only 2 years old, so certainly should still be working.


You need to check that the motor drive belt is OK and turning freely to drive the water pump - under the flap on the right side at the front as you look at the front of the Bissell. If this is OK have you filled the cleaning bottle with fluid e ... Vacuums

Bissell pro heat 2x multi surface carpet cleaner making spots


Maybe there's not enough vacuum or it hasn't been primed enough. I have a proheat that drove me crazy till I started leaving the heat switch on. I get wads of carpet fiber that mat around brush and spit out on the carpet, so I frequently remove them ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Hi I own a Bissell Proheat Powersteamer pro-tech with a turbobrush. I have been using "bissell multi-allergen removal formula for carpets and upholstery." I ran out of that last night. Today I went to walmart looking for more. Everything I found said "2x Ultra Concentrated Bissell multi-allergen." I'm confused on where to add the cleaner. I have a water tank and a separate soap tank. The instructions on this new cleaner bottle say to add 4 capfuls for the formula tank and dilute with hot tap wat


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have a bissell pro heat water wont come out


The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the way to ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

We have a Bissell Pro-Heat 9200 2X Carpet Shampooer. When you start to shampoo the carpet it runs water for a minute and then quits and won't spray any more water.


The heater is clogged. Take off body assembly. There is a silver part in there the size of a dollar bill. with seven screws. That the heater element. It is clogged known problem on there bissels. Crappy design for one. But most causes are not useing ... Bissell Vacuums

Bissell pro heat carpet cleaner, won't move forward. both belts working. is there something that is suppossed to hold the brush bar down so the carpet cleaner uses that as it other set of "wheels"


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0780 seconds