Having problems with your Bissell 8910 ProHeat Clear View Upright Vacuum ?

Cleaning under floor nozzle window

\015 I removed screws from the clear window to remove build up but can't remove it. How do I get it off?\015

Answers :

Make sure you removed the 2 screws closest to the front then lift up on the front end of the window sometimes its sticky but it will lift up. when putting it back on put the tabs on the back end in first then slip it down in the front , replace 2 screws
Repair Help & Product Troubleshooting for Bissell 8910 ProHeat Clear View Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cleaning under floor nozzle window


Make sure you removed the 2 screws closest to the front then lift up on the front end of the window sometimes its sticky but it will lift up. when putting it back on put the tabs on the back end in first then slip it down in the front , replace 2 scr ... Bissell 8910 ProHeat Clear View Upright Vacuum

How do I remove the floor nozzle window in bissell dirtlifter to clean out the scunge that is blocking the air suction?


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bex bissell powerwash de luxe removal of floor nozzle window to clean


... Bosch Vacuums

The heated solutions only sprays out to the floor in a 3 inch area. It takes a long time to clean the floor with only 3 inches available. Are there some nozzles somewhere on the machine that I need to clear out? If so, how do I access the nozzles?


There are two nozzles (either red or white) on the unit located behind brush. Use an old toothbrush to clean them off and that should resolve the spray issue. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Floor nozzle window


Remove the tank tip back there are 2 screws take them out you will have to tug on the lens some times they stick just make sure you tighten the screws good after ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a Bissell 1623-1 Steam Cleaner. It will work good for about 2 minutes and then after that it will not dispense cleaning solution on floor or through the hand held wand.I have replaced both drive belts with no improvement. I have cleaned it and found no obstructions in hoses and spray nozzles, put back together and it still will not dispense. Is it possible the pump or solenoid is no working? Aaron


... Bissell 1623 Steam Cleaner

I have a Bissell Proheat Turbo 2x model 9300. It has stopped spraying at the floor. The hand tools will work so I assume this means the problem is at the base somewhere. I cleaned the nozzles but don't know what to try next. It has always had a problem with dumping too much cleaning solution as well, don't know if this is a contributing factor


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell proheat cleaner is letting out little spray solution when on the floor cleaner setting. If I press the sprayer on the attachment solution comes out of it even when it is not set on the attachment setting what should I do to fix i. How do I clean the water nozzles under the machine?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Water wont come out when handle pressed to do floor or out of nozzle for upholstery cleaning smells hot when trying to get it to work could this be a belt


Yes it most likely is the belt ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a hoover 3000 i have not used in awhile, and since I removed a large rug, I would like to use it again on my slate floor. HOWEVER, I cannot get it to pick up ANY water in the water recovery unit......it is dry, dry, dry. I have put in a new filter, cleaned the nozzle unit, the scrubber , and reconnected both the recovery unit and the water unit several times, but to no avail. I would like to get a graut attachment a well as replacement part, but since I can't get the basic unit to work, I


Have you made sure the plastic filter cover with the round hole in it that covers the filter is in place ( part # 59177096 ). This piece seems to get lost, and without it there is no pick-up. The other common problem is that the wheel assembly has be ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Fllor nozzle window blockage


Take the 2 screws out near the front outside edges then just lift it off ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Need floor nozzle for Kenmore Home Cleaning system Model 175.8690090; no longer supported by Sears


Unfortunately without seeing something like this it's difficult to know.Find a local vacuum store if there is one in your area. Take your old wand they should have something in stock to fit your wands. Internet is great to save a buck but nothing bea ... Kenmore Vacuums

How difficult is it to remove and reinstall the floor nozzle window on the 7901-1 pro heat cleaner. We loaned ours out and it was returned in foul condition. Thanks


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Noise Hi... I was doing normal house work and had been using it on carpet... I put it on floor for my hardwood floors and picked up loose clean cat litter and went to put it back on carpet and it made a horrible noise like it was rubbing. cleaned the filter... cleaned the roller thingi ...checked the belt and it is still making that horrible noise. It does not make the noise when I have it on floor but as soon as I put it on carpet it screams at me. Help! Please and thanks Linda


Hi Linda,\015\012Sounds like clutch problems, try to move the lever for carpet/floor back and forth a few times maybe it will free up. If it still makes the grinding noise, the clutch assembly will have to be replaced. Let me know, i can even ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have the Hoover max Extract 77 and when I'm cleaning the carpet, the clean water tank leaks on the floor, even if I'm not squeezing the trigger. The clean tank doesn't leak when I fill it, but once I place it where it fits and start using the vacuum, the clean water drains out on the floor. The dirty tank fills up, so the suction works, but, I don't know what is going on?


... Hoover Vacuums

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T


... Rainbow E series Canister Wet/Dry Vacuum

I have a new Euro-Pro shark model S3101. Used it one time and while I was doing my tile floor in my kitchen I reached under a cabnet to clean and hit the floor kick kind of hard and broke the head off of the shark. I have only the T shaped end on the shark now with the cleaning head broken off and looks unrepairable. I did kind of hit the floor kick hard but the plastic broke like glass. Can I put a new head on the remaining piece or is it repairable? thanks Angie


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Pro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Can't clean out a part; need help


The nozzle will seal very tight along the sides, pry up with somethin like a flat blade screwdriver to pry it loose. When you re-install it, make sure the 2 tabes at the top edge of the window snap into the slots first before putting it all of the w ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I've cleaned a few areas and now the blue nozzle part with the dirt needs to be emptied. I do not have an instruction manual and can't figure out how to open or detach the blue nozzle part to empty it & clean it out.


Release the handle under by the front wheels. It will then pull out. Once you pull it out,on the frame there is a diagram showing out it comes apart. ... Sharper Image SI570 Steam Wizard Handheld Wet/Dry Vacuum

My Scooba (brand new battery) won't spray water out to clean the floor. What should I do? I've tried over and over. It moves in circles but no fluid will come out to clean the floor!!!!!


Ive had that problem and what i did was put the tank in the kitchen sink and turned the water on blast and let it everything flush out through the diffeiirent outings in the tank. Also (i think this was the actual solution) i got the little blue squ ... iRobot 5800 Scooba Vacuum

We brought 2 packs of your cleaning floor wipes,the end result is very streaky,making a one step operation into a two step operation.after cleaning the floors of our b/room and kitchen,which are both


... Vacuums

Poor cleaning I recently bought the Shark Steam Mop as I read mainly fantastic reviews. I was disappointed to find that it leaves a slight film on my dark hardwood floors when finished. I can wipe the film away with my finger and you can see foot prints if walked over. I also found that there are cloth streaks on my ceramic floors after drying as well. I followed all instructions, vacuumed beforehand, used distilled water even though my water is not considered hard, cleaned slowly, etc. I am wo


Hi,This type of problem usually is not he fault of the Shark Steam Mop.The problem is the old residue left on the floors by other cleaners.Here is a tip that I wrote that will help you out with that problem... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

When vacuuming hardwood floor, hair gathers on brush and never sucks into vacuum. I spend most of my time cleaning off brushes. How do I clean hardwood floor with dog hairs.


1. Broom and dust pan, then mop\015\0122. Wet dry vac with wide non-brush attachment\015\0123. Here's a link to a vacuum professing to clean pet hairs well\015\012\015\012 ... Sebo Air Belt C2.1 Bagged Canister Vacuum

I used my Hoover FloorMate, SpinScrub Hard Floor Cleaner for the first time today. My intent was to clean the grout in my kitchen/family room floor. Since the water was dirty I know it cleaned the grout but I was only so-so pleased with the results. Any hints? What about the grout solution? Do you mean I can only use the Hoover product?


The Hoover model 800 has seperate brush assembly to do grout. The 500 model (yours) has only the one hight brushes so other means must be taken to do grout. I have a 500 and all tile floors and I'm bumbed too.\015\012\015\012Kirk Thompson ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.


I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0413 seconds