Having problems with your Bissell 8910 ProHeat Clear View Upright Vacuum ?

It won't **** up water except with tool attachment

\015 My vaccum has worked great for about a year. I pulled off the clear front to clean out the lint buildup, but since then it will not **** up the water when using the regular vacuum, it will squirt the water just fine! It will **** it up when I use the hose attachment, but that is too much work for the entire floor! I have made sure to switch from the tool attachment setting to the floor setting, but it doesn't help. Is there a seal loose or something! Help, my carpets are soaked!!!\015

Answers :

When you took off thew clear nozzle, you must have lost the black oblong gasket that sits at the junction at the top for the tank lip to sit on. Without it, you lose suction at that point.
Repair Help & Product Troubleshooting for Bissell 8910 ProHeat Clear View Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It won't **** up water except with tool attachment


When you took off thew clear nozzle, you must have lost the black oblong gasket that sits at the junction at the top for the tank lip to sit on. Without it, you lose suction at that point. ... Bissell 8910 ProHeat Clear View Upright Vacuum

My Bissell 9200 wont always pump water to the tools


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The tool attachment for the hose on my Bissell ProHeat 2X CleanShot won't spray soap or water. The bristles on the tool rotate without a problem and the suction is working fine, it just won't spray water when I pull the little gray trigger on the tool.


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell vacuum attachments wont work, as soon as i attach anything besides the crevice tool it wont ****,but sucks fine when its just the hose


Tern upside down remove plastic cuvier look wear the hose gos fillip skew driver ... Bissell 6594 PowerForce Bagless Upright Vacuum

The tool attachment won't spray water-


You almost have to open up the unit and follow the hoses from the handle into the base.fill it with solution and turn on pull triger.hold the triger in and turn off the unit keeping the triger pulled.turn off and start it up and try again.if it don't ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Shampooer not sucking up water- water is spraying out and the hand tool is working but the main body wont **** up and water


Change the selector from hand tool to floor cleaner ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My hose tools wont pick up. when hose tools unattached suction is fine and will **** my hand fiercely, but once tool attached no suction..... how am i gonna pick up cat hair from seats now?! its a dyson DC04 but it wouldnt let me choose that!


I have a DC04 and the hose tools are a open hole.The only reason they want pick up is they are blocked.If you say they are sucking your hand when not attached.Make sure the hose is not blocked by taking off the cover at the front.Allso check the cyli ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Bissell 8920 wont spray any water/ solution except when in water


It sounds like you have a clogged line, if your mechanically inclined you can fix this yourself by tearing the unit apart. If you open the unit up, disconnect the lines on your pump and blow an air compressor through them. certain lines require you ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a


The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

II have the kirby sentria, i have it in canister mode with blower attachment on the hose is on with the hand sprayer attachment the problem is the foam is not coming out the sprayer used it just fine all day went to refill w/ water and cleaner now the foam wont come out whats wrong with it?


Make sure the "straw" is in.See if dust coming out of the hose did not clog the air passages. ... Kirby Heritage II Vacuum

My Hoover steam vac is stuck on the tools setting and wont stop leaking water from the tools hose


... Hoover Vacuums

Shampoo attachment wont pick up water


How do i hook up ... Kirby Ultimate G Bagged Upright Vacuum

I have a Hoover SteamVac Spot/Deep Cleaner, model F5515. I've had it a little over 1 year. It will not extract dirty water from the floor. I've made sure the recovery tank is attached correctly and also that the stair tool is connected. Is there something else I can try??


... Vacuums

Bissell Proheat 9200-H, won't pick up water to bottom tank, except by hand tools.


This could be the problem ... Bissell Vacuums

Hoover steam vac upholstery tool wont spray water


... Hoover Vacuums

The bissell proheat turbo carpet cleaner is not sucking up the water from the vacuum or the tool attachment.


Bissell cleaner will not **** up water??? ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hmmm Hi there, I actually had tried everything you mentioned except for the vinegar idea which I'll do when I get back up to my home in Oregon. I checked for pinches, the heater, etc. Water does NOT come out of the accessory tool and only will dispense out of the main area for a second or two..any liquid actually starts filling up the area right behind the nozzles and around the pump instead of OUT of the machine. I checked gaskets, made sure there was a tight seal, and even made sure the little


Check the nozzles to make sure they aren't clogged. Sometimes there is a problem with the flow indicator cap, maybe too tight or not tight enough. Try squeezing the trigger while turning the can one way or the other. If at a certain point it starts ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Little suction and pours water underneath machine on the floor. This all happens while i am using the hand attachment tool, but also occurs when i tried just the machine is running..what am i doing wrong. it is new..only used once about 6 months ago


Press the handle release kick-button with your foot, extend the handle all of the way back, and take a look at the gap between the base of the unit and the handle/reseviour assembly. You should see several black hoses attached to the base and running ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

My steam cleaner pro heat 2X will not spray water. we have even tried the tool attachment and still nothing


Sounds like you may have lost the pump prime turn the unit off and hold the trigger down the one on the handle for a full minute then turn the unit on if that does not do you might have a clogged pump hose or a bad pump hope this helps you out ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Water wont come out to shampoo , but comes out furniture tool


You need to replace the pump belt. Here are the belts you need:Bissell Proheat Belts ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Bissell proheat 2x no heater light also not spraying water from bottom belt going round also tool attachment working power fine


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hoover F5915905 wont spray tool attachment - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Pickup water wont pickup the water after putting it down very little comes up into the tank .it worked fine when we baught it but after not useing it for some time it worked now it wont **** water up at all can anybody help.


The clear shroud covering the front of "hood" has two sheet metal type screws at the bottom in front of the brushes, these two screws also hold the little straight brushes ( one on each side) in place. I found one of these screws had broken it's plas ... Hoover F6020-900 SteamVac Upright Vacuum

I have a george wet and dry (A26A), it wont pick up any water. the tube which goes from th lid into the water wont pick up water?


... Vacuums

Rainbow Series E is leaking. Not sure if water is leaking from the water bin (doesn't appear to be cracked/broken). If not the bin, where else might water be leaking from and what are repair options? Have replaced belt on carpet attachment, cleaned the opening where hoses attach to the canister, etc


You need to clean the separator. ... Rainbow E series Canister Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0456 seconds