Having problems with your Bissell 9200 Upright Vacuum ?

Won't spray Checked everything four times and nothing is clogged. It sprays once in a while but only for a few seconds. I'm about to toss it and buy a hoover unless someone can help me trouble shoot now.


Answers :

Ensure you have water in tank and solution (or water in solution tank). When you start the vacuum up, the pump starts to prime itself. If you have air in the system, it takes a little longer to prime. Allow the vacuum to run for 1 minute before attempting to pull the trigger. Then pull the trigger.
\015\012If this doesn't work, you'll need to open the unit up and check the hoses for any clogs, and next test the pump to see if it is functioning.
Repair Help & Product Troubleshooting for Bissell 9200 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Won't spray Checked everything four times and nothing is clogged. It sprays once in a while but only for a few seconds. I'm about to toss it and buy a hoover unless someone can help me trouble shoot now.


Ensure you have water in tank and solution (or water in solution tank). When you start the vacuum up, the pump starts to prime itself. If you have air in the system, it takes a little longer to prime. Allow the vacuum to run for 1 minute before attem ... Bissell 9200 Upright Vacuum

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

My brand new Hoover F914-900 steam vac spin scrub will not release the water. I have tried all of the trouble shooting advise in the owner's manual.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Trouble shoot hoover 5914-900 steam vac


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac F5871-900 trouble shoot


... Vacuums

On my M&S Air Vac AV425 central vaccuum system, the system usually turns on by inserting the vaccuum hose into one of the vaccuum outlets. However, it now runs continuously. I am able to turn it off only by unplugging the vaccuum from the electrical outlet. I would like to know how to trouble shoot the problem or how to find someone who services Air Vac systems in the Bridgewater, New jersey area.


We are a central vacuum service company and we service all of new jersey. sounds like you have a short some where that keeps your unit running or it could be your relay module thats stuck our number is 908-721-7595 its j&j central vacuum services ... Vacuums

I have bought new Hoover bags on two occasions. The first spares I bought were the Xxxl variety and I didn't think they fitted that well. The next spares I bought were the type g megafilt. I still feel like they do not fit that well and the suction power on the vacuum is not as good. I'm I buying the correct replacements? I followed the guidelines on the Hoover bags the vacuum came with. These were printed as the right bags to buy. I only have the vacuum around a year and thought it was brillian


... Bosch BSG71310UC Bagged Canister Vacuum

CARPET/fLOOR tOOL Electrolux Hoover Model EV4602. Need to buy the plastic connector from stainless steel tube to the Carpet/Floor tool. If necessary buy a new floor tool We live in Cape Town do you know a stockist for spare parts for Elecrolux Hoovers near to us


... Vacuums

Hoover upright 2000w, HL2005 001 problems:the hoover made a pop sound & turned off. Tried leaving it for 30 mins as suggested in the manual but it still won turn on. Really cannot afford to buy a new 1 & would like to fix it. partner is an electrician so if we have some guidance as to what the problem may be i am confident we can fix it. the hoover is only 18 months old so not very old at all.


... Vacuums

Dusty smell i buy loads of hoovers and always same prob .when i hoover its a dusty smell and it stays around bag not full and check filter the hoover is ok f couple days then this happens


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=41018&thid=618510\015\012Dusty smell\015\012Posted by chekle on May 23, 2008\015\012I buy loads of Hoovers and al ... Hoover F5881-900 Vacuum

Want to Buy a Repair Manual for Bissell Proheat 9500 Clean Shot


I have the manual and would be more than willing to share...contact me at [email protected] ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Turned Hoover on and worked as normal for 10 mins then for a split second went off and then on again a coupe of seconds later went off completely. Tries different socket and changed the fuse. Still not working.


Internal short most likely to a feed wire to the motor ... Vacuums

What model is now popular hermes bags? I want to buy a hermes bag, but I have no time to go out to buy, can only look on the net. But to see many stores, are not sure that good, is quality goods. Can someone give me a shop's web site?


... Vacuums

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?


Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy


Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil


Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums

Brushes won't spin on a Hoover Steamvac SpinScrub Model F5918-900


Well the hand tool works off the suction of the machine and has nothing to do with the turbine that controls the brushes. if you can get the part i can walk you through taking it apart. when you write back, let me know what the model num of your mach ... Vacuums

When i switch my henry hoover on it works fine for exactly 50 seconds then switches of for approx same time then comes alive again for 50 secs and so on...driving me nuts.


... Vacuums

My hoover elite belt comes off within 5 seconds of turning it on


Those machines sit in the box in transit across the world and waiting for purchase. In time the rubber stretches out from just sitting there. In the old days they packed the belt separate from the vacuum and you had to put in on yourself. Today's buy ... Hoover Elite Rewind Bagless Upright VacuumVacuum

Hoover steamvac shooting sparks from motor


The motors shot some times i have fixed them if it hasn't been ran to long let me know im sure i have a motor ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Where can I buy the felt polishing for the Hoover Floormax F2300


... Hoover Floormax F2300 Upright Vacuum

Hoover windtunnel I HAVE REMOVED BOTH BELTS AND I DO KNOW HOW TO PUT THE LARGE BELT BACK ON BUT THE SMALL ONE IS GIVING ME TROUBLE


Put the V belt on the pulley first, then the flat belt, put it over the motor shaft or pulley, then you have to stretch it to go over the pulley next to the V belt pulley. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0555 seconds