Having problems with your Bissell 9200 Upright Vacuum ?

Bissell Pro 2X. The brushes spin as soon as I turn it on but only spins for an instant then it quits spinning. The vacuum stays running. the handle is down.

Answers :

It might be the drive belt slipping if the unit is off then the belt is locked onto the belt and then when the unit is switched on the belt slips and if its loose it doesnt hold the belt to the motor shaft 
Repair Help & Product Troubleshooting for Bissell 9200 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell Pro 2X. The brushes spin as soon as I turn it on but only spins for an instant then it quits spinning. The vacuum stays running. the handle is down.

It might be the drive belt slipping if the unit is off then the belt is locked onto the belt and then when the unit is switched on the belt slips and if its loose it doesnt hold the belt to the motor shaft  ... Bissell 9200 Upright Vacuum

My dyson d17 will only stay on if the handle is tilted back and it's not sucking at all....although it's running. When i stand the vacuum up with the handle upright, it cuts off.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

4296 Robotic Vacuum _ Brush quit spinning

I had the same prob. i contacted i-robot and was told the motor that turns the brush is shot. there is no replacement part. they offered to replace my i-robot with a new one from the 400 series. at about 60% of a new one. that's the only option that ... iRobot 4296 Robotic Vacuum

Burning smell While using the vacuum, the running light will get dim. If I hold the handle at the point where the light gets dim the motor will start smoking. I can either raise or lower the handle and the light will brighten up and the vacuum will run fine. Any ideas???

Hi theres two things that could have made it start doing that 1 the whires have a short in it or 2 the motor has gon faulty. you might want to buy a new machine ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.

Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r

... Vacuums

I have a new Dyson upright vacuum. The vacuum will not stay on. I used it a couple of hours ago with no problem, but now it won't stay on. It seems to be sucking and running normally otherwise. What can I do. Thank you. Donna Eakman

Hi Donna, My name is Don.\015\012\015\012When you say it wont stay on could you please advise the following:\015\012\015\0121. Does it cut out suddenly as you are using it?\015\0122. How long can you use it before it cut ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Power Problem Whenver I push the power button on the handle the vacuum stays on for a few seconds then turns off. I have to push the button on the handle all the time to keep the vacuum working.

Hi There,\015\012\015\012Unfortunately this is being caused by static electricity building up in the electronic controls in the handle of the hose. I've seen this problem on numerious occasions, and in fact I have the twin brother of t ... Miele Blue Moon Bagged Canister Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!

Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Telescopic handle I don't think I have the exact same vacuum, although mine is a fantom upright bagless. I can't get the telescopic handle to stay in place. It pulls out whenever I try to pull back the vacuum. Any tips would be helpful! Thank you

Sometimes the locking mechanism for the wand wears out, make sure u have it all the way in and look where it locks and see if it looks worn ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

Our miele red star(s314i) vacuum was running great and quit suddenly. It had not been running for a very long time and just quit. Newish bag, no clogs in hose and doesn't seem overly hot. the over heated warning light did not come on. I've waited 30 plus minutes to try to restart and no luck. Any ideas

Ok, so if the cord test didn't fix the problem, then it sounds like either the plug has gone bad, or the switch. The plug is a very common problem to go bad, and can be caused by just simply yanking the plug out of the wall, or putting too much tens ... Miele Red Star Bagged Canister Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

We have a Kenmore Progressive Model 116 Upright bagged vacuum with Hepa filter. It's at least a couple years old. For quite some time now when ever we use the vacuum the vacuum motor will shut off nafter about 5 min. of use. We then need to let it sit for awhile and then we can run it again for another 5 min. The bag has been change. Any one have any ideas how to fix this?

I suspect that you have a restriction. The motor sounds like the thermal break is stopping the motor before damage, due to heat.\012You must witness that the entire suction and discharge side are clear. This is not always very easy, but necessa ... Kenmore 34612 Bagged Upright Vacuum

Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?

... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the

Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

I have a Kirby Heritage Vacuum Cleaner. Recently the handle fell backwords. I took the pin to the handle out and replaced it. It helped some, but the handle does not stay upright.

... Kirby Ultimate G Bagged Upright Vacuum

Our vacuum will not stay running.. We have cleaned both filters several times since dyson told us there was a switch which turns the vacuum off if the filter in the ball was dirty, but we still need to keep pushing the switch several times to turn the unit back on while vacuuming.

... Dyson DC25 All Floors Bagless Upright Vacuum

GE Spacemaker Microwave PVM1870 fan keeps running after door closed and won't shut off. Have to open door or unplug. As soon as door is closed and plug is back in, fan starts up. If door handle is pressed downward, microwave starts! If door handle is raised, fan shuts off but light stays on.

... Vacuums

Brand new LG LUV200r used 10 minutes now after removing dust tank & reinstalling the vacuum motor does not run only the beater bar??? I have located wo circuit breakers both seam to be set. This suction motor should run when the switch is pressed & the beater bar should operate when the handle is moved down??? Not A happy customer will return unit to Best Buy only 100 mile round trip!!!! RDH

... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

My vacuum has not been running right..the beater bar is not picking up and the rollers aren't spinning...the belt doesn't need replaced so what else could it be...everything else seems to be running fine???

The motor shaft that spins the belt may have hair wrapped arount it, causin the belt to slip. You can't miss the burnt odor.\015\012Remove the belt and clean the motor shaft. ... Vacuums

Regarding my Kirby Generation 3 upright vacuum cleaner: the handle does not lock into place, but rather falls to the floor. Any thoughts on how to get it to stay in place? Also, I lost my owner/operator manual. Can I download one to learn how to clean and maintain the vacuum?

The plate that catches the handle to lock has a hidden spring behind that plate.I would leave it alone for the unit is pressed together. Used ones are found most everyday on Ebay. The owners manual maybe found on this website\015\012\015\ ... Kirby Generation 3 Bagged Upright Vacuum

The roller brush on my Hoover Z700 vacuum no longer runs when you tilt the handle back. I have tested every part that I can: the motor is good; the "magnetic switch" at the pivot point is good; etc. I'm now stumped. Any help or suggestions would be greatly appreciated as I don't want to throw away a $400 vacuum.

Has this not got a rubber belt drive? ... Vacuums

I have a model 116.35922 beltless drive vacuum. The agitator brush will not turn with the vacuum running and the handle down. The brush turns by hand and the reset button has not popped. Ther is nothing wrapped around the brush, but it does feel to have some resistance when moving by hand.

Wich bags for vacuum cleaner kenmore model 116.35922 ... Kenmore Vacuums

Motor quit working. i was vacuuming and all seemed fine. then the motor went really low. when I opened it I noticed that the bag was not attached and the cannister had filled up with stuff and the filter was full. the vacuum will not run now.

My friend, the dirt you sucked up went right into the motor and it burned up. I am very sorry to tell you this. It is probably not worth repairing unless you are able to replace it yourself.\015\012\015\012In addition to not being able ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum


  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1214 seconds