Having problems with your Bissell 9200 Upright Vacuum ?

There is nothing that is clogging the tubes in the vacuum and the belt is still working. but there is no suction


Answers :

Even though the brush is spinning, you probably need to replace the belt2_bing.gif\015\012because it is stretched. It is probably slipping on the beater bar.

Jim
Repair Help & Product Troubleshooting for Bissell 9200 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

There is nothing that is clogging the tubes in the vacuum and the belt is still working. but there is no suction


Even though the brush is spinning, you probably need to replace the belt\015\012because ... Bissell 9200 Upright Vacuum

I have a Eureka Contour model 2900 type A upright vacuum, the roller works fine nothing clogged, took it apart motor blade is free of debris, no suction from tube and blasts OUT air from the front HEPA filter location. New bag, New belt, nothing in hose.any clues as to why this can be happenning? Air should not be blasting out of the HEPA filter.


Even with your explanation,it seems the hose is clogged.Try taking the hose off,then blow through it or pour water through it.If this doesn't do it,make sure the suction canals are going to the proper areas. ... Eureka 2900A / 2901A Contour Bagged Upright Vacuum

My kenmore vacuum model 116.36933502. It has no suction. I have cleaned out every spot,taken off the back and still nothing. The motor runs but doesnt seem to be at full power. The agitator brush works. When it broke i seemed to smell something and since it has no belt. Does this possibly have to motors?


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I


You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

The vacuum i've had for 6 months has very liittle suction power. checked that the belt is on. cleaned filter. checked to see if hoses were clogged. I used a super vac to suction any debris out of vacuum. still little suction power


As this unit has 3 filters on it, a lot of people forget about the one filter that will cause all of your trouble here. \012\012There is the exhaust hepa filter, no problem, your unit is pretty new, it shouldn't be a problem. \012Th ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My hose no longer works no suction buth the vacuume still works how do i fix I checked the hose checked the filters nothing works to get my hose so it has suction.


Check the following after unplugging the power cord from the outlet.\012\012- Check for suction at the back of the unit, after removing the hose where it attaches to the back of the vacuum. If there is NO suction, the machine will need to be ta ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Dyson suddenly stopped working. About a week ago it had a suction issue. One of the upright tubes was clogged, cleared it and it worked fine. Today I was vacuuming and it simply powered off. The vacuum is maybe a year old give or take some.


Hi its Darran at Dyson.Sorry to hear you are having difficulties with your Dyson. So that we can help, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US). One of our advisors will be able to run through some ... Dyson Ball DC24 Bagless Upright Vacuum

My eureka vacuum was fine but then suddenly got loud. We cleaned the filters and replaced the belts, but it is still loud. We have not seen any clogs in the tubing or in the vacuum. What other problems could the vacuum have to make it loud?


The noise could be coming from the Beater Bar's ball bearings. ... Vacuums

The suction still works but the primary floor vacuum doesn't. I checked the belt and its not broken. The engine that runs the floor vacuum doesn't engage like it used to


The belt doesn't have to be broken to affect the the way the vacuum picks up on carpet. If the belt is stretched then it will slip and not turn the roller brush properly. Here is the manual and belts you need: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The vacuum does not have suction from the beater bar. The wand has good suction and the belt is still in place on the bar. There are no apparent clogs. What could be the problem


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho


Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

I have looked online for this vacuum but could not find it. The closest one is the Eureka 8803 but the p/n on mine says 79307. I have totally disassemble this vacuum. There are no clogs anywhere. Motor spins by turning shaft. Belt is new and turns brush. It still has absolutely no suction.


... Eureka Boss Capture 8803AVZ Bagless Upright Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Ive got a dc07 dyson just changed the belt on it as i had to since then it isnt picking anything up at all nothings clogged up had it to bits and put it all back together again properly. The hose is working when i take it off its got plenty suction but when i run it along the floor it picks absolutely nothing up any ideas that i havent thought off. Thanks


Sounds like the hose underneath has become detached. Have a look and if its not that come back to me. Also can yo9u check your U Bend is still on as these can come off. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Vacuum My vacuum is loosing it's suction power. I've checked the belt and it's in perfect shape...I've bought a new filter cup...I've checked for clogs and there aren't any...I've cleaned the entire machine...and I still can't find the source of the problem.


You checked the belt, but I bet it has stretched and won't drive the brush roll under load like it should. Belts only last a few months the stretch and should be replaced. Iff you have suction at the hose, then it has to be down below, either belt/ ... Eureka Whirlwind 4480 Upright Vacuum

I HAVE A FANTOM VACUUM CLEANER MOD.#F1205400. I PURCHASED IT ABOUT 6 OR SO YEARS AGO.IT WORKS PERFECT,AS FAR AS SUCTION, THE ONLY PROBLEM IS ABOUT 2 MONTHS AGO,SOMETHING HAPPENED TO IT AND IT GOT VERY LOUD, KIND OF LIKE A CAR WITHOUT MUFFLER. I TOOK IT APART,AND FOUND NOTHING OBVIOUS. CAN YOU GIVE ME SOME IDEA OF WHAT I CAN CHECK TO RESOLVE THIS PROBLEM. AS I SAID BEFORE IT STILL VACUUMS GREAT. THANK YOU, VINCE


You probably have a bad motor bearing. I don't know if the motor is available now or, these older Fantom's are obsolete along with most of their parts. ... Vacuums

The vacuum suction still works but the brush wont turn. It still looks like the belt is intact and attached properly.


The problem with Dysons is that the belt breaks and sits in position.If you can turn the brush by hand, with little or no resistance then I would say the belts broken.If in doubt take the cover off and look. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Panasonic model MC-V6830 works but no suction. I checked and belt was loose, but there is nothing to attach the back of the belt onto. Seems some screws or plastic pully part/parts are missing. What parts do I need to order to fix this vacuum?


... Panasonic Vacuums

Belt is not broken, brush roller still working, and still no suction at all. Have not located any clogs.


... Riccar 8955 Upright Vacuum

My Hoover Platinum LiNX Cordless Stick Vacuum beater bar is not turning. After removing some clogged hair and items...the vacuum cleaner has suction, but the beater bar will not turn. What to do? The belt is still attached and will turn manually.


... Hoover Platinum LiNX Cordless Stick Vacuum

Luv300b vacuum brushes won't spin. The belt is fine but still not working. Any suggestions?


... LG Electronics Kompressor Plus Upright Vacuum Cleaner LUV300B
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1410 seconds