Having problems with your Bissell 9200 Upright Vacuum ?
Does the end of the upholstry thing come apart to clean?
The tool itself does not come a part but it does detatch from the hose so it can be rinsed under the faucet.
Repair Help & Product Troubleshooting for Bissell 9200 Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Does the end of the upholstry thing come apart to clean?
The tool itself does not come a part but it does detatch from the hose so it can be rinsed under the faucet. ... Bissell 9200 Upright Vacuum
My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.
... Bissell 1960-3 QuickSteamer Plus Upright Vacuum
I need an operational manual for a beam central vac model 178. It came with the house and I need to take it apart and clean it. Does the filter thing inside the system come off. It is caked in dust and dirt and I think it is effecting the performance of the vacuum.
It's an upright, model X4. The bag full or clogged light is lit. I've takent the thing apart and cleaned it out, and removed some clogs. But the light won't go out and when I run it, it stops after a minute or so. Also, the pedal for lowering the machine to use it has come off and I can't figure out how to reattach it.
There is a short hose inside the housing where the roller is. Did you unclogg this as well? ... Sebo Vacuums
Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o
Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.
That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums
I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi
Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums
It clicks as it is going and stops after about 30 seconds. Two beeps. I have tried cleaning brushes and have pretty much taken the whole thing apart, cleaned the motor, the brushes everything. Still doing to same thing, when this has worked before.
It clunks because the gears are damaged. You will need to replace the CHM. If you have the red cleaning head module, chm, replace it with the green chm. ... Roomba Robotic Floor Bagless Vacuum
I am wondering how I can clean the inside of my bissell spotlifter powerbrush hand held cleaner? I want to clean the part where you suction up - it is full of gunk and hair and I can't figure out if it comes apart or not so I can clean it. Can you help?
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=49876&thid=506980\015\012I am wondering how I\015\012Posted by carriespets on Apr 12, 2008\015\012I am wonde ... Bissell SpotLifter 1716 Bagless Handheld Vacuum
My sister dropped her roomba than brought it to me complaining it does'nt work anymore. I took it apart, cleaned everything i knew to clean,could not find anything obviously wrong so I put it back together.I charged the battery than tried it. The green light comes on when you push the clean button and it makes a little grunt noise but that's it.
Have a look at the motor brushes if there broken or poped out this is were the "grunt is coming from" the motor is trying to turn but cant? ... iRobot Roomba 4000 Bagless Robotic Vacuum
Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?
Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum
The holes on my dyson dc07i are dirty and smell how can i get them clean does the part with root cyclone on it come apart
Hi Susan,\015\012\015\012We'd strongly advise against attempting to disassemble the cyclone pack, as this is likely to snap the internal bin-base release rod, and can also reduce the performance of your machine. \015\012\015\012If you ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Roomba discovery My roomba comes off the charger and will go about a minute and a half. Then it will stop and beep once. i checked roombas sight and they said that the brushed need to be cleaned. I cleaned the brushes 6 times. It still does the same thing. I bought it from you in November of 2007. Should I bring it back to your service department?
Greetings doreen f,\015\012\015\012The roomba unit carries a one year manufacturers warranty, so you should be able to bring it into your local Best Buy™ store and have them try to repair it. \015\012\015\012I hope this ... Roomba Robotic Floor Bagless Vacuum
Water will not come out when i push on trigger button. So water does not come out. I have taken it apart and cleaned it. The problem seems to be in the triggerI push on the handle to release the water.
Order the part from bissel see if that fixes sound like you know what wrong just need get part number from bissell.Could be some kinda pump also thats bad not pushing out the water.I got bissle heated one black it only problem the seals r ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
UGH! We cleaned this thing in and out even took it apart and cleaned the gears with Q tips. It's SO LOUD lol what in the world is that noise?!
Maybe the gears need lubrication like WD 40 o9r CRC spraw? ... Vacuums
My dyson vacuum cleaner doesn't seem to have the same suction power it used to. I have cleaned out the canister and have taken apart the vacuum head (for cleaning carpets) and it doesn't seem to be blocked but it seems to lose suction by the time it reaches the head. The suction is strong at the end of the hose (where you attach the telescopic attachment with vacuum head) Any ideas? Thanks, Irene
Bissell Quicksteamer I have a Bissell Quicksteamer that is about 5 years old. I went to use it today and hardly any solution was coming out. I could see it suctioning up what little came out, so I took it apart and cleaned it thoroughly. I tried to use again and no solution is coming out. Everything seems to being working just fine. Thanks
Here's a kinda kick yourself quick fix that might be helpful, I took my whole machine apart all the way to the motor to come to realize that the small rubber piece that cover the tip of the water container was jammed in the hole you sli ... Bissell 1770 Quicksteamer II Upright Vacuum
I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?
Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums
I got my bissell for $7.50 from a thrift store, if you can believe THAT. Used it for the first time today after reading the manual online first. After filling the clean water bladder full of hot water and setting everything up the way I wanted, proceeded to turn things on and go for it. Well, the water/solution just kept coming and coming, without my finger on the trigger. Obviously something is jammed in the open position but where? The trigger moves freely.
This is the answer I got from Bissell:Please\015\012check the gasket at the bottom of the tank to ensure it is attached and\015\012not lodged in the reservoir of the machine. If this is not the problem,\015\012take the machine for i ... Bissell 8910 ProHeat Clear View Upright Vacuum
Irobot roomb will not work. I've discharged the battery and recharged for 16 hours. Acts like it is going to come on but sort od revs up and then gives a series of 6 or 7 or 8 beeps.. Goes so fast I cant count them. I've cleaned everything. Aftertyring a couple to Times, it seems that the battery discharges... Clean light goes red. Please help... i need this thing to work!,,
... iRobot Roomba 550 Vacuum
How do I clean out the dirty water container? Does it come apart? Rinsing it w/ clean water is not enough.
... Bissell 1425-1 Little Green ProHeat Canister Wet/Dry Vacuum
I noticed that the little side brush doesn't turn anymore and the Dirt Dog stops about every minute now so I have to keep turning it back on! I have dismantled the brushes and cleaned everything out but that didn't help at all. It doesn't really come apart any more than that for cleaning. Any suggestions as to where my problems may lie?
... iRobot 1100 Dirt Dog Bagless Robotic Vacuum
I have a dc17 and there is a clog in it. I have taken the brush off, cleaned the hose, but there is something up inside the hose on the side that I can't get to. how to I take things apart so I can see to unclog it.
On the back of the vaccuum theres is a screw with a ubend hose...did you remove that? I have had things stuck in there which stopped suction? you may want to check that. also take the wand off and look through to make sure you can see light throug ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The water doesn't come out. I've taken it apart
The reason the water is not dispersing is because the pump belt is probably stretched or worn. You can get belts and view the manual here: ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Have a Eureka Power Plus 12.0 Amps Model 4702 Type A 120 volts and 60 HZ that there is something wrong that it isn't picking up right and you can actually feel the air coming out of it near where the bagless canister attaches. My thoughts are that a seal is missing around where the hole lines up when the cannister is locked in. This Vac was my Mom's and she passed away and I think a part went missing maybe when it was taken apart to clean the filter and empty the canister. Need to figure out if