Having problems with your Bissell 9200 Upright Vacuum ?

MY BISSELL SEEMS TO HAVE THE SAME PROBLEM AS EVERYONE ELSE - NONE WHICH TO MY KNOWLEDGE HAVE BEEN RESOLVED. MY MACHINE WILL DESPENSE BUT NOT SUCTION - WHAT GIVES WITH BISSELL -IT THIS AN ONGOING PROBLEM


Answers :

Please check the following: \015\012


\015\012

First check the motor duct gasket. The motor duct gasket is visible once the tank is removed. It is located underneath the handle on the top of the base of the machine. It has a black rubber coating around it. If there is no suction there please let us know. If your machine does have suction at the duct, continue to check the following:
\015\012


\015\012

- Ensure the Ready Tools Dial is set to the appropriate setting (Floor Cleaning or Hose Attachments).
- Remove the tank from the machine and ensure the tank lid is attached properly. The front window must first hook onto the lip of the bottom of the tank and then drape over the tank. Latch the bottom tank to the top tank lid. THIS LID CANNOT BE ATTACHED PROPERLY IF THE TANK IS NOT REMOVED FROM THE MACHINE.
- Make sure the Water Tank is not full on the outside of the bladder. If it is, empty the tank.
- Ensure the hose is firmly attached to the back of the machine. If not, re-insert as necessary by twisting into place.
- The machine must be in an upright, locked position and set to the Hose Attachment setting. If the handle is slightly tilted back while using, it will create a small gap at the suction inlet (where handle meets gasket, above the Bottom Tank) which will cause little or no suction.
- Check the red Tank Lint Screen for debris. If the Lint Screen is dirty, the unit will have poor suction. Clean the Lint Screen if necessary.
- If the float flap door in the tank lid is activating prematurely when you turn the machine on, this flap door should be replaced. This tank may need to be emptied.
- Check the Tank Lid and Tank for damage.
\015\012


\015\012

If you continue to experience low suction contact BISSELL Consumer Services at ...
\015\012

1-800-237-7691
Mon-Fri: 8am to 10pm ET
Sat: 9am to 8pm ET
\015\012

Repair Help & Product Troubleshooting for Bissell 9200 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

MY BISSELL SEEMS TO HAVE THE SAME PROBLEM AS EVERYONE ELSE - NONE WHICH TO MY KNOWLEDGE HAVE BEEN RESOLVED. MY MACHINE WILL DESPENSE BUT NOT SUCTION - WHAT GIVES WITH BISSELL -IT THIS AN ONGOING PROBLEM


Please check the following: \015\012 \015\012First check the motor duct gasket. The motor duct gasket is visible once the tank is removed. It is located underneath the handle on the top of the base of the machine. It has a black rubber co ... Bissell 9200 Upright Vacuum

I purchased my Bissel PowerSteamer Clearview a few years or so ago, and cannot find where I filed the manuals. If I find the actual seriel number on the Bissel PowerSteamer Clearview, Is there a way that I can purchase another manual? I really do not have any problem with my Bissel, but being I am 75 years of age and do not use it myself anymore, I want to give it to a daughter of mine (but I would like to have the manuals that go with it to give to her also).


No need my friend. Go here. All documentation is here...and....it's free! Hope this helps : )http://www.bissell.com/user-guides/?searchtext=1699%2520pro%2520heat&searchType=search&mode=228 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance


Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

I recently purchased a bissell proheat 2x and have used it several times with great results, the problem I am now having is no water being released from the bottom of the machine and the gauge is not spinning. What could be the problem. I have taken the machine apart thinking maybe something is clogging it.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No suction from my Little green machine - Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum


Hello and welcome to FixYa;Make sure the collection tank is not full, that it is seated correctly the handle is locked upright to ensure a good connection \015\012between the tank and the rear cover gasket. ... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

Either of my bissell porheat turbo 2x or my bissell pro heat don't have suction i would like to try and trouble shoot if i could due to the fact i am having difficulty finding a small machine repair center in my area could you possible help me or send a link which could help me find solution these machines are not more then a year and a half old if that thanks for your time and help warmest regards rebekah majors


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL


... Bissell 1200A SpotBot Pet Robotic Vacuum

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.


Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No suction vacuum working fine and suddenly, no suction at all....what could be the problem? no suction through the machine from either the wand or the floor/brush side


Sucked up a sock?? No seriously.. it may be as simple as that or that an on board filter is clogged. Check your manual for all filters and Hepa/screens and others. Also, is the unit making any odd noises since the non -suction scenario? Whining or s ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Suction I have no suction through the hose. I have taken this machine apart, and checked for clogs, have found nothing, but did give it a good cleaning, still I have no suction.


Hello tnwalkergal the hose may have a clog inside the hose at the bend you can take the hose loose and run a broomstick or a yardstick thorgh the hose this is how I find the clog ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Poor suction I have a hoover hush s5627 vacuum purchased about 4 years ago from Costco. It's suction power isn't so good anymore. I've checked all the lines & hoses and they're clear and I've changed the bag. I even disconnected the pipe from the vacuum unit and held my hand over the intake. While the machine roars like a jet engine the suction power just ain't like it used to be. What could possibly be the problem?


This vaccuum has a Fan Blade inside connected to the motor that spins to create the suction you feel. After a few years of use (and misuse) the blades on this (plastic) fan will be broken off, thus damaging the unit. These Fans are replaceable if yo ... Vacuums

I posted my problem earlier today that I was having with my Bissell Little Green Machine not dispensing solution, but sucked up no problem. Someone said that the most common problem was a blockage. We put hot water in the reservoir for 15 minutes as advised and it still will not dispense. The fluid is now ''dribbling''so it is better. It is just not spraying. We are able to blow from the end and make bubbles in the reservoir which shows us it is not blocked. Any other suggestions?


Okay. I fixed this on mine. Undo the screws on the handle, right by the trigger. You pull the tubes off the little valve. Push on the button and see if you can blow through the valve. If not, push a pin around in the valve (with it pushed into the ... Bissell 1720-1 Little Green Wet/Dry Vacuum

Hi, My problem is that I'm getting hardley any suction when I vacuum. The machine has a new bag and the rollers are turning, just no suction. Thanks!


Take out the brushroller and check the hole where the dirt goes into the machine for clogs.\015\012\015\012Marci ... Hoover Vacuums

I bought a used Hoover Reind and there are two issues:1) There is no suction. The debris flies out of the back of the machine and 2) The machine will not shut off. You have to unplug it in order to get it to stop working. Any suggestions on either problem?


... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

Hello, I just bought a Bissell Powergroom (model 92L3-W) vacuum and a Bissell Proheat Pet (model 8910-3) deep cleaner and I love them both. My problem is, when we unpacked them we somehow lost the manuals; I think I had too many helpers that night – they may have gone out to the trash with the boxes. I need replacement manuals if you would be so kind as to help me out. Could you email me a manual for each of these two machines, or tell me exactly where to find them online? I’ve been looking, but


Follow the link below and enter the model numbers to access the User's Guides.\015\012http://www.bissell.com/customer-support/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have power but no suction - Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum


Im sorry to say, it sounds broken..... i know of this great site that sells bissell's for like half of retail check it out.....maybe your best solution.... ... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

Currently my dyson does not work when in the upright position. When I pull the handle back, it will run, but the suction is not very good at all. I tried washing the filter, but that didn't work. Sometimes it works for awhile, but then the problem occurs after the machine has been used for awhile. What do you think the problem is?


Hi its Darran at Dyson.It sounds as though the brush bar may not be turning properly when you put the machine into the upright position. To test, lie the machine on its side in the vacuuming position (head released) then switch it on and ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hello, I have an Electrolux vacuum. In desperation, I vacuumed up some water and my machine stopped. I am hesitant to take the machine to a repair place for fear that if it is a simple repair they will not be honest. Can anyone give me advice on whether this is a problem that requires a new motor or major repair? Thank you!


Although it's never to be recommended, it is sometimes possible to vacuum up a little water without doing significant damage. However, the fact that your machine then stopped suggests that the electrics got wet. That may or may not have caused expens ... Vacuums

I HAVE A FANTOM VACUUM CLEANER MOD.#F1205400. I PURCHASED IT ABOUT 6 OR SO YEARS AGO.IT WORKS PERFECT,AS FAR AS SUCTION, THE ONLY PROBLEM IS ABOUT 2 MONTHS AGO,SOMETHING HAPPENED TO IT AND IT GOT VERY LOUD, KIND OF LIKE A CAR WITHOUT MUFFLER. I TOOK IT APART,AND FOUND NOTHING OBVIOUS. CAN YOU GIVE ME SOME IDEA OF WHAT I CAN CHECK TO RESOLVE THIS PROBLEM. AS I SAID BEFORE IT STILL VACUUMS GREAT. THANK YOU, VINCE


You probably have a bad motor bearing. I don't know if the motor is available now or, these older Fantom's are obsolete along with most of their parts. ... Vacuums

Bissell I inherited the Bissell Model 790 Steam Vac. No solution will come out. Apparently it's clogged somewhere as the previous owner appeared to have used it to vacumn up a powdered carpet cleaner. How do I resolve this problem as the machine is barely used and I would like to salvage it. Thank you


Check the belts first, if ok, does water squirt out of the hose nozzzle, if it does then the heate in the handle asm. is clogged where the tubes hook up to it. If no water squirts out, the the pump isn't working. Pull the top cover off, check all t ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My Bissell spot bot does not **** the cleaning fluid out to the carpet. It has suction from the carpet to the machine but not from the machine to the carpet?


... Bissell 12005 Spot Bot Handheld Vacuum

Bissel vacuum My bissel powerforce somehow is loosing its suction Ive no clue why Ive checked for clogs etc. but Icant find the problem please help!!


Take the dirt cup out and turn the bottom of it that will let you get to the filter,there should be some finger twist plates on the top,turn and take it out,there will be a foam cover around the filter,take that off and clean with warm warter,when do ... Bissell 3522 PowerForce Bagged Upright Vacuum

No suction - Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum


Check to see if there is a clog somewhere. Like elaing1978 said we need more info on whats wrong with it. ... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

We have the bissell quicksteamer and as I was shampooing I began to notice something burning so I unplugged our machine immediately; then my mom and I started cleaning all the filters assuming that could be the source of our problem and yes it was a little dirty but I suspected that it would take more thant that to cause our machine to somke soI turned it upside down and noticed there is a cable of copper threads that appear to have some type of rubber or plastic insulation tubing around it but


Was the exposed copper wiring on the electrical cord? If is then replace the cord. The main problem with this model is that Bissell obsoleted it as well as parts for it. But if all you need is a cord, you should be able to get one from a repair shop. ... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

Why is there no suction - Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1409 seconds