Having problems with your Bissell 9200 Upright Vacuum ?

When button is pressed, water does not come out of the holding canister. still seems to have suction, but water doesn't come out to rinse/clean carpet.


Answers :

Please check the following with liquid in both tanks.\012


\012

- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.
\012

- Check for debris on spray tips. Clean them with a soft brush (on old tooth brush works well). The spray tips may be lifted out for easier access.
\012

- Ensure the tank lid is properly attached to the bottom of the tank. To attach this properly, remove the Water Tank from the machine. Hook the front window onto the lip of the bottom container and then allow the window with lid to cover the complete tank. Secure the latch on the back of the bottom tank to the back of the tank lid. THE TANK LID CANNOT BE ATTACHED PROPERLY IF THE BOTTOM TANK IS ALREADY INSTALLED IN THE MACHINE.
- Check the bottom of the Water Tank and the Formula Tank to make sure each has a red auto-load gasket attached. Make sure the Water Tank and the Formula Tank are seated properly. Depress the x on this gasket to ensure this depresses and release back out. Liquid from the tank should dispense.
\012

- Remove the handle completely and re-attach. Once the handle is re-attached, re-attempt to spray.
\012


\012

If the machine continues to not spray, check the following:
\012


REMOVE THE COLLECTION TANK:
• Make sure the unit is set to water rinse
• Remove the smart mix bottle and fill it with water only
• Place the smart mix bottle into the collection tank reservoir
• Run the unit and try to spray. If the machine sprays, you will be able to see the water level decreasing in the smart mix bottle and you will need to replace the bottom tank. It is possibly warped.
\012

Repair Help & Product Troubleshooting for Bissell 9200 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.


That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:Bissell Pump ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

When button is pressed, water does not come out of the holding canister. still seems to have suction, but water doesn't come out to rinse/clean carpet.


Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for debris o ... Bissell 9200 Upright Vacuum

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

Parts Hi I have the Eurkea steam cleaner model 2450 and was wondering how do you take the front part off where you can see the water sucking up from carpet so this can be cleaned. Also I think the spring in the part that holds the water has come off another part is this able to be fixed or can I just purchase a new water holding tank and if so where? Thanks


Click this link for spare partshttp://www.vacpartswarehouse.com/Eureka-2450-extractor-s/1802.htm ... Vacuums

My Bissell proheat 2x model 9200 is not dispensing cleaning solution. I hold the trigger and the carpet doesnt get wet at all. i poured water on the carpet and it sucks it up. the cleaning solution does mix with the water but it not being dispensed on the floor.


Hi, \015\012when last did you service the machine?\015\012\015\012i believe should service the machine.\015\012try to open the machine.\015\012\015\012when opening make sure you notice where the part you are remov ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Poor suction...continued Wow, thanks for answering so quickly! To answer your question, yes, there is suction at the screen, but it is very weak. I keep that screen clean. As a side note, I noticed that when I remove the top clear plastic cover (that would be part # 37 on the diagram, as far as I can tell) there is decent suction coming from the intake there--part 36? 30? it's hard to tell. But with the cover on, I feel no suction (from where it sucks up the water directly from the carpet),


Wish I had it in my shop, it is hard to figure your problem. I do know that you must have something out of place and you may have to take it apart to find it. You may feel some suction there at the top of the clear nozzle, but maybe it isn't strong ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

I got a used bissel 1720-9 bissel cleaner..It holds water,,and turns on but no water comes out the nozzel?? what side of tank do i put the water in also there was no instructions,,there is suction when i turn it on but no water,,


You can download a user guide from www.bissell.com Just type your model number in the search panel ... Bissell 1720-1 Little Green Wet/Dry Vacuum

Foaming When vacuuming the shampoo into the dirty water bucket. it foams up so bad, It will only hold 1 1/2 cups of water. its a 2 quart bucket. then the float shuts off the the air and I'm left with foam coming out of the bottom of the mach. on to my carpet.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

When I squeeze the trigger, water won't come out of my Bissell PROheat2X carpet cleaner. The beater bar rotaotes, and there seems to be suction. Nothing comes out the bottom.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a new STEAM VAC Dual V All Terrain Carpet and Hardwood Cleaner. I have used it once and it worked well. Now, the second time, I have no water return. I checked the tank location, the brushes are moving slowly (but the plastic surrounding around the brushes moves as well ??) Water is coming out. There is hot air blowing out, but there is no air suction. What is wrong? Ursula Litzcke


Hello litzcke.\015\012There are lots of people facing this problem as well as other problems with this machine. As there are lots of faulty with this product; would not **** up water/air/shampoo, will not brush and lots more. If it is under war ... Vacuums

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

When I clean my carpets and hold the trigger only water comes out, there is no soap leaving the container . I have a Bissell pro heat 2X carpet cleaner.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell Carpet Cleaner pro heat- water doesnt come out


The screw that is located in the center of the handle, that holds the assecory hose holder must be tight. My screw was missing, put one in and cured the problem. Sounds stupid but it worked. Got this idea off the Bissell web site. Also if you have a ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Bissell PROheat 2x carpet cleaner the water doesnt come out of it either from the bottom or the tool can it be plugged somewhere?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The carpet cleaner comes on and the heat source is working in it, but the machine is not dispensing the water and cleaning solution. It does have consistant suction. What could cause this type of problem?


Most likely a bad belt you might think it looks good but i'd say thats your prob after you replace it you should be fine if not we can go deeper ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

We have a bissell and it the one to clean the carpet how do we use it i no to put hot tap water and turn it on and hold the grey thing to make the soap come out but nothing is picking up well i dont see nothing


Take this link to Bissel website, select your model and download yor free operation manual.\015\012\015\012http://www.bissell.com/ ... Vacuums

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.


... Hoover Vacuums

I own a Bissell Proheat Pet Model 8910. After just a few uses and changing both the brush and pump belts (trying to resolve problem) carpet doesn't get wet any longer. Carpet solution comes out normally but the water barly leaves the section of the tank I fill water into, resulting in carpet recieving to much solution and not enough water. Any advice?


... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!


Call BISSELL Consumer Services.\015\0121-800-237-7691\015\012Mon-Fri: 8am to 10pm ET\015\012Sat: 9am to 8pm ET ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 - On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 - not


Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a bissell proheat 2x and it leaks water around the wheel it holds dirty water but doesnt hold clean water.......and how do i remove the wheel on my bissell


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Suction problem my proheat wont suction water out of carpet,,, it made a mess of my carpets now, any one no how to fix the suction problem?


The valve on the bottom of the water bucket is not being pushed up enough to allow the vaccuum to go through. Perhaps a part is missing but I used a small ball bearing and a car vaccuum cap to build it up and now our works but it is still a piece of ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

DIRTY WATER THE FRESH WATER AND SOLUTION COMES OUTON TO THE CARPET, BUT NO DIRTY WATER IS COMING INTO THE CANISTER.


Remove the dirty water tank and see if the front nozzle is fitted correctly, also see if the filter is clean on the dirty water tank ... Bissell 1770 Quicksteamer II Upright Vacuum

WHEN I PUT THE MACHINE ON TO CLEAN TH CARPET THE WATER DISPENSES INTO THE CARPET AND THE BRUSHES do not SPIN and theres NO SUCTION TO REMOVE THE WATER FROM CARPET


Make sure the lower tank lid is on securely, clean the intake filter on the top right of the machine. ensure the front panel is installed (the square to remove for hoe use). this has to be in place for carpet operation ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0679 seconds