Having problems with your Bissell 9200 Upright Vacuum ?

My 9200 - T machine will not pump water or solution when pulling the trigger


Answers :

Repair Help & Product Troubleshooting for Bissell 9200 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bissell model 8910 pro heat will pump solution or water for like the first couple times you pull the trigger as you can see the mixture window spinning. After that it stops spinning and nothing else will come out until you turn the machine off, and restart. Then again same process works for a couple trigger pulls then quits.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

My 9200 - T machine will not pump water or solution when pulling the trigger


... Bissell 9200 Upright Vacuum

Hey there, a friend of mine has a bissell pro heat 2x turbo, that is spraying no water on the floor setting, the pump works i assume, as the machine vibrates when the trigger is pulled, how would i troubleshoot this problem.


Check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- Check for deb ... Bissell Vacuums

No Suction The water/soap solution dispensing just fine but when I pull the machine back over the water solution, it is not being sucked up (usually it is easy to see as it you can see the water being pulled up through the clear plastic)


It sounds like the lint filter is clogged. It is located on the top clear plastic piece (the one with the dial to switch from floor to tool use) and is on the underside. It is a small (1 inch square) red plastic piece with a little door on it. Fli ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

Bissell Powerease Lighweight Deep Cleaner. (Shampooer) After I fill the solution tank with the solution and water, I put it in it's slot, but all of the contents just come flowing out. I have only used this machine twice and it worked ok. You are supposed to press the trigger and the solution sprays out and then release the trigger when you want it to stop. But like I said, now I just put the tank on and all the contents come flowing out. I don't know what's wrong or how to stop it.


... Vacuums

No water I have a Bissell 1694 and it is not ejecting the water cleaner solution out of the front of the machine. The belts are ok. The two nozzels and hoses are not clogged and do not have any holes. I think the pump still works because water still comes out of the brush tool.


It is easy to take the top off. Mine has just 6 screws. Then you can see all the tubing and parts. For example, you can unclip the nozzles and see if water flows. Try blowing through the nozzle to see if it is plugged.\015\012\015\012Some people s ... Bissell Powersteamer 1694 Upright Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

I have a Bissell Proheat model 7901. When I pull the trigger on the handle, there is no water flow. The brushe revolves and the unit vacuums any water spilled on the floor. Could it be a failed pump or kink hose or ? Thanks Zap


Take the handle apart and put spring back into place. ... Bissell Vacuums

I brought an eureka model 2591av shapoo machine in 2004 I've only used the machine 4 times. now the it does not spray out the solution on the floor but it will **** up water, the vacuum part works. I took it to a repair shop, they said it was the pump that was broke and will cost $95.00 to fix. The purchase price of unit was only $129.00 My question to you is does that sounds like an honest or comparible diagnosis.please respond at ([email protected])


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=559297\015\012Generic problem for all Vacuums\015\012I brought an eureka model\015\012Posted by wadda08 on Apr 3 ... Vacuums

Bissell Pro-Heat 7901-1 no cleaning solution is pumped out. The flow indicator is spinning and the belt is spinning the beater bar. Have cleaned the flow indicator, checked vavles in the solution tank and water tank and they are working properly. Also checked the trigger to make sure it works okay. Any ideas?? Moody Fan


Bissell Pro Heat shampooer - Fill the soap dispenser with extremely hot water and shampoo with only water for a few minutes. There is often dried soap in the lines. Make sure that all filters are clean. Press the soap container and the water conta ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Why would the water and cleaner solution come out without me pulling the trigger? Thanks


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The unit isn't pumping water or solution when the trigger is depressed. I've replaced all belts and the motor works fine. Any help?


You might have a blockage in the heater its very common  ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I have Hoover Floormate Model H3004. The machine will no longer dispense the cleaning fluid due to the trigger assembly not engaging properly with the inlet/outlet on the Clean Water Solution Tank. I have checked and made sure the tank was seated properly.


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Bissell 7901-1 The soap doesn't mix with the water when I pull the trigger, I can see the soap isn't being used when I do the carpets. What can I do, have no problem taking this machine apart.


If the mix valve knob is turning smoothly, then most likely the cap and valve for the sop bottle is bad. Also make sure that the seal is on the cap at the bottom of the bottle and not sitting in the hole. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!


Call BISSELL Consumer Services.\015\0121-800-237-7691\015\012Mon-Fri: 8am to 10pm ET\015\012Sat: 9am to 8pm ET ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Steam doesn't come out anymore when I pull the trigger. I think the water in the tank is getting hot, but when I pull the trigger, only a little water comes out. No steam


Try putting some white vinegar in the tank to dissolve any hard water deposits. You should use only distilled water in this machine. Don't try to clean anything with the vinegar in it, but take it outside to run the vinegar through. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a Saeco Armonia Espresso Machine. The water pump was running when the tank ran out of water and when I refilled the tank, it wouldn't start again. I unpugged it and turned everything off overnight. The pump is very loud and won't pump any water.


Common on Armonia...There is no water in the system, so the pump is pumping air!!you have to push on the usual button but make sure the hot water button (for tea for ex) on the right side (same as steam opening valve) of the machine is op ... Saeco Vacuums

I own a Bissell Proheat Pet Model 8910. After just a few uses and changing both the brush and pump belts (trying to resolve problem) carpet doesn't get wet any longer. Carpet solution comes out normally but the water barly leaves the section of the tank I fill water into, resulting in carpet recieving to much solution and not enough water. Any advice?


... Bissell 8910 ProHeat Clear View Upright Vacuum

FILLING INSTRUCTIONS. I HAVE A BISSELL PROHEAT PLUS 12 AMP CLEANER. HAVE LOST MY MANUAL. NEED INFO ON FILLING THE MACHINE. DO I MIX THE BISSELL CLEANING SOLUTION WITH THE WATER? IS THERE A SEPERATE PLACE TO PUT THE CLEANING SOLUTION, IF SO HOW MUCH SOLUTION PER WATER CONTENT. THANKS


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Attachment problem used a new unit w/attachment for 5 minutes...dispensed solution in a powerful triangular fashion. Then the fluid quit dispensing out of the attachment nozle amost like the pump quit working. Primed the unit several times w/ no success. checked for clogs. can't tell if the floor portion is "pumping' or just dribbling solution onto the floor with the trigger. can see no leaks at this point. unit worked for about 5 minutes on apholstery


Make sure everything is filled and secured tightly, if this a new unit it should be something simple ok, also check where machine folds down that the solution hose is not being pinched its right behind the dirty water tank ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Bissell proheat 2x model 9200 is not dispensing cleaning solution. I hold the trigger and the carpet doesnt get wet at all. i poured water on the carpet and it sucks it up. the cleaning solution does mix with the water but it not being dispensed on the floor.


Hi, \015\012when last did you service the machine?\015\012\015\012i believe should service the machine.\015\012try to open the machine.\015\012\015\012when opening make sure you notice where the part you are remov ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The water pump on my bissell pro heat 2x does not seem to stay primed , the water does not flo continually when trigger is pressed. should i replace the pump or the fittings?


... Bissell 8920 ProHeat 2XTM Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0536 seconds