Having problems with your Bissell 9200 Upright Vacuum ?

Bissell 9200-T ProHeat 2X will not spray I have gone through the priming process it will work for a few seconds and quit. I have had it open and checked a few tubes but not sure what to do next. This occurs with both the Upholstery attachment as well as the bottom sprayers.


Answers :

\012ARE THE TANKS SEATED PROPERLY AND THE AUTO-LOAD GASKETS
\012IN PLACE?
\012Check the bottom of the Water Tank and the Formula Bottle to make
\012sure each has a red (or black) auto-load gasket attached and facing outwards
\012and that the ventilation tube is not submerged as it allows air in so the solution
\012can flow.
Repair Help & Product Troubleshooting for Bissell 9200 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell 9200-T ProHeat 2X will not spray I have gone through the priming process it will work for a few seconds and quit. I have had it open and checked a few tubes but not sure what to do next. This occurs with both the Upholstery attachment as well as the bottom sprayers.


\012ARE THE TANKS SEATED PROPERLY AND THE AUTO-LOAD GASKETS \012IN PLACE? \012Check the bottom of the Water Tank and the Formula Bottle to make \012sure each has a red (or black) auto-load gasket attached and facing outwards ... Bissell 9200 Upright Vacuum

I need to find a way to replace the attachment hose on this unit. the tube to spray the detergent snakes into the base next to the wheel and i'm unsure of how to take it apart without breaking it. is there a simple way to remove the wheel? do i need to do something special to replace that tube?


The best thing for that situation is to look on the side of the road and you will find a Bissel, I see one or two a week. Take one home and experiment on that one not yours. I have brought many and never have I bought one. I never see a Hoover by ... Bissell 9200 Upright Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Vacuum tube is obstructed at curve next to roller. I'm unable to clear it using a chop stick. vacuum functions when tube is used w/ attachment for small areas.


Do not give up... Now try wire coat hanger to clean out. Restriction of air flow will burn out your motor, eventually. ... Bissell Vacuums

My problem is the brush on the bottom is not spinning and i think there is no suction from the bottom of the vacuum my rugs are in need of a vacuum and i 'm not sure what is going on - also nothing is going into the canister


Is there a shaft driving the brush, or is there a belt on this one? Are they intact and working properly? It could be possible that the motor isn't moving which would cause no suction or brush movement. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Rainbow Shampooer Where do the two tubes go at the bottom on the canister? Easy to hook up the hose but no place to hook up the tubes.


It's been while since I used one. Hopefully things haven't changed.\015\012\015\012One hose has to be be connected to the faucet of the sink using the adaptor. The other hose is supposed to go to the Rainbow iteslf.\015\012\ ... Rainbow E series Canister Wet/Dry Vacuum

I have an old kenmore sewing machine. When i run fabric through, the bottom stitching turns into a total rats nest. Its as if the bottom is pulling a ton of thread for each stitch. The top stitching looks fine. Not sure what to do and i am a total beginner at sewing! thanks


Check the tension on the bobbin thread and ensure that the bobbin is in the right way, the thread must double back on itself. ... Vacuums

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.


You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

I broke the handle part of the shark steamer #53101. I don't have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom


Hi,Ann there are very few parts for these...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.


You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Dirt Devil Vacuum that won't start up anymore. It was working, but then it stopped. The tube got clogged up. Now the tube is unclogged and empty and it won't turn back on. It's also hot on the bottom of it. Help? Blown fuse or what?


Some of the Dirt Devils have a reset button on the back, near the bottom. But if the it is getting hot on the bottom, that may mean the motor is trying to run but can't. Maybe something has jammed it. You would have to disasemble it to find out. ... Vacuums

There is a blockage occuring at the first bend right above the roller brush.It appears to be caused by a broken piece of white tubing within the black tube/


Hi Vstanle,you have diagnosed it correctly, the best solution to your issue is to have the part replaced which is available from the link below. ... Oreck XL2200 Bagged Upright Vacuum

The fan housing tube is cracked just below the bottom clamp. How to replace


... Oreck XL21 Bagged Upright Vacuum

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger


There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums

I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?


Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum

I have the same problem with intermitant power, however, it does not make sense that the problem is in the upper powerhead (which is what a repair guy told me) because-- when I use the other attachements it is fine. The problem only occurs when I use the carpet (big)attachment so that the roller will not turn. Couldn't it just be in the area where the bottom of the handle attaches into the carpet attachment?


You can test the auxiliary plug to the roller/beater attachment with a volt meter if you know how and take precautions. Check for 115-120 volts at the beater/roller attachment plug. If voltage is there and the beater/roller doesn't run, the proble ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Hi my vacuum isnt sucking up like it should, actually hardly at all, the brush on the bottom is spinning, not sure what is the matter with it


Check all the hoses and filters for any blockages. ... Vacuums

It won't turn on. I have partially disassembled it and have continuity between the power cord (wide blade) and one of the connectors where the switch assembly snaps in. Also, switch is working fine. There is continuity across it, then no continuity across its connectors when the switch is pressed. Not sure what to try next.


\015\012Please provide the make and model. Thanks. ... Vacuums

My brush is no longer working on my bissell healthy home vac. when i try to turn it on it makes a high pitched squealing sound. I'm pretty sure it needs a new belt but my husband is having trouble getting the vac. apart. He says you need a special tool to get the screws out of the bottom of the vac. Any advice? THANK YOU!


Hi,\015\012 According to Bissel, they should be standard phillips screws. Nowever - things change.\015\012This is a general guide from Bissel for belt change - \015\012 ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Changing belt How do I do that? It looks like I would have to take the screwdriver to the bottom and enter the engine compartment. I'm not sure that I feel confident to take this machine all apart and be able to get it back together again.


Its not the engine compatment take the screws out the cover 4 the roller will come off then u can c where the belt goes ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Missing curved trap tube at bottom of vac


It is called a u tube ... Dyson DC07 Bagless Upright Cyclonic Vacuum

HI! i am not sure what the part is called that i need for my DC07. I can point it out on the vacuum. i think it is a hose that connects the bottom part of the vaccuum to the bucket part...i am sorry that i am not more specific.


It is called an "AI VALVE" - it looks like a Tuba and has two buttons that you push to take it off the machine - it sits into the square hole above the wheel and connects to the round hole next to the dirt bin. Call the Dyson helpline to order the pa ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vacuum I have a dirt devel purpose for pets vacuum. It has worked well previously. The vacuum has started spitting out debris from the bottom when slightly lifting from one floor to the next. What could be causing this. Thank you


You may have a clog in the dirt inlet by the brush roll, and also the hose. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0294 seconds