Having problems with your Bissell 9200 Upright Vacuum ?
Where to open up unit to check for clogs - Bissell 9200 Upright Vacuum
This link below is for the service repair manual
Repair Help & Product Troubleshooting for Bissell 9200 Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Where to open up unit to check for clogs - Bissell 9200 Upright Vacuum
This link below is for the service repair manualhttp://lib.store.yahoo.net/lib/vacuumcleanerbacgs/bissell-proheat-2x-repair-guide.pdf ... Bissell 9200 Upright Vacuum
I have a new bissell 50c9 upright vacuum and it keeps clogging in the clear window in the back. there is a flap that keeps coming open and filling up. everytime i clean and restart, the flap opens. i tried holding it closed and noticed lose of suction.
Bissell 35962 Cleanview Bagless Revolution Upright Vacuum hose is clogged with sock where hose meets handle attachment. Attempted to use broom handle to push back through suction opening. Sock is compacted. Any home repair advice?
If you have access to a small sink "snake" used to clear clogs in sinks, you might be able to use it to "snag" the sock and pull it out.\015\012Needs to be a metal sewer snake so that you can tug on it if and when it snags the sock. ... Bissell 35962 Cleanview Bagless Revolution UprightVacuum
No suction using extension hose for Bissell Bagless Upright vacuum. i checked for clogs and found nothing. shannon
Check the sole plate where the beater bar is. You may have to remove the roller brush flap to get into the roller brush and then check the main dust channel beside it. Usually if there's no suction on the hose it means that:\015\012\015\0121) T ... Bissell CleanView II Plus Upright Bagless VacuumVacuum
Bissell 37604 Bagless Upright Vacuum. Hose keeps clogging every time I vacuum. Is there a way to prevent this? I am ready to buy a new vacuum, but it does do a great job picking up hair...until it clogs. It clogs at top of hose. Could the hose be kinked? It does not look like it.
That is a defect in the design of that style of vacuum. I went back to my old vac because I got so tired of having to unstop it. The sharp turns in the hose and the molded plastic causes it. Find one without the turns. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum
I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth
When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums
I have a bissell healthy home vacuum and the roller bar on the base of it is not working. I have checked it for obstructions and it is clear. I have also tried reseating the canister and just about everything I can think of. It's almost like the switch that deterrmines whether or not the vacuum is in the upright position is broken and always says it is upright... any way to fix that? Thanks, Scott Hammersley
... Bissell Vacuums
Bissel vacuum My bissel powerforce somehow is loosing its suction Ive no clue why Ive checked for clogs etc. but Icant find the problem please help!!
Take the dirt cup out and turn the bottom of it that will let you get to the filter,there should be some finger twist plates on the top,turn and take it out,there will be a foam cover around the filter,take that off and clean with warm warter,when do ... Bissell 3522 PowerForce Bagged Upright Vacuum
We have a Bissell Revolution Lift-Off Turbo 3760-1 and the upright brush is not working/rolling. It only moves when pushing the vacuum. We checked the belt and it seems to be fine. The vacuum works fine as a hand-held. Any suggestions? Thanks!
These belts need to be changed every 6 months regardless of the way they look. ... Vacuums
Bissell healthy home vacuum will not turn on. I have checked everything on the vacuum. All the filters are clean and there are no clogs. I have had it for 10 months with no issues until now.
- The handle may not be installed properly, causing a loss in the power connection. Remove the handle completely. Slide the handle back into place on the lower section of handle and tighten the screw. ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
My Bissell started to **** up my daughter's stuffed animal. I quickly turned it off and pulled the stuffed animal out. Now my vacuum won't pickup. Not sure what to do. I have unplugged the vacuum and checked for clogs. Please Help!
Did you check the hose. The vacuum won't **** if there is a clog in the hose. ... Bissell 6594 PowerForce Bagless Upright Vacuum
My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.
... Electrolux Vacuums
How to I check the belt for the vacuum? - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
There are some instructions for the pump & brush belt at http://www.bissell.com/WorkArea/DownloadAsset.aspx?id=629 and the general user instructions http://www.bissell.com/DownloadAsset.aspx?id=635 ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together
My Kenmore progressive upright vacuum, model 11635923500 has a problem with the brush rotating. Sometimes the brush will not rotate until the unit in lowered way down, like the activate switch has rotated. Can I get inside the unit to check the switch, if so were do I look
... Kenmore Vacuums
No suction and is not clogged - Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
The motor is bad, when these type of electrical motors go bad the power of the vaccum dies but the motor can still sound like it is running. One way to tell the motor is shot, is the motor while running will be a might louder than it was originally. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
How to open vacuum to check belt - Dirt Devil M088300 Upright Vacuum
... Dirt Devil M088300 Upright Vacuum
The hose will ****, but not the main unit - Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum
Empty the dust canister and clean out the bottom filter ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum
My Bissell upright CLeanview (model 53F8)is constantly getting clogged up. I have to reach up into the upper filter chamber and pull down all the yuck that I have vacuumed up. It does not even make it to the dirt container. Gross!
The red light indicating dirty surfaces does not come on. The vacume cleaner seem to work but i get no or very little suction from the flexible tube ... Bissell CleanView 3596 Bagless Upright Vacuum
I have A BISSELL UPRIGHT STEAM PRO HEAT AND IT JUST STOPPED SUCKING I TOOK APART AND CLEANED EVERYTHING CHECKED THE HOSES FOR CLOGS AND IT STILL WONT WORK
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.
I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
How to remove and clean the whole unit - Bissell 6594 PowerForce Bagless Upright Vacuum
Start removing screws from around brush cover and back of unit. Usually all the screws are the same style/length but be sure to check while removing. Once you have all the covers off, you should be able to access all the areas that would be cleaned. ... Bissell 6594 PowerForce Bagless Upright Vacuum
The extension arm of my Dyson Animal no longer has any suction. I can attach it but it has extremely limited power to reach high places or under furniture. Also, when I stand the unit, used as vacuum, upright and the top valve opens, there is a strange noise that wasn't present when I first purchased.
You have a blockage within the wand or at the u-bend at bottom of the hose....try removing wand and see if u hav esuction at end of hose...if so wand is blocked,if not removed u-bend ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
How to check the location of the pump belt? - Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Take off belt cover on the left side of the top cover, turn cleaner over, take out screw from red lock and remove, pull cap and brush roll out, unhook the cogged belt, then you can replace the pump belt thru that opening. Put belt over the pump pull ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.
- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum