Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

Brushes won't turn and vacuum will not pick up sprayed cleaner

\015 Motor runs strongly but brushes don't revolve and no cleaning solution is picked up.\015

Answers :

There's a Capt. Obvious fix to check before you go any farther. Like many vacuum cleaners, the brushes on the Bissell carpet cleaners, by design, only spin when the handle is not locked in the upright position, so be sure to plug it in, turn it on, and depress the foot pedal to lower the handle while watching the brushes one more time to be sure that the fix isn't that easy.
\015\012
\015\012If the brushes still won't spin with the handle in the unlocked position, lift the handle back up into the locked position, power off and unplug the Bissell, and look down and see if either of the two belts that make the brushes spin are broken, as a broken belt, or a belt that's come off the track, is the next most likely problem. Both belts must be unbroken and in the right place for the roller brushes to spin.
\015\012
\015\012These belts can be seen in the clear plastic pieces on either end of the roller brushes. If you're having trouble locating them, **with the Bissell unplugged so the brushes won't suddenly start spinning and hurt your hand**, try spinning the brushes with your fingers while watching for the belts. They're black, about the thickness of two quarters, and the bigger one of the two (on the left end of the roller brushes, as you face the front of the Bissell), is just big enough to fit around both roller brushes. The smaller belt, goes around the back roller brush on the right and to a smaller cog wheel behind it. If you see a broken belt, or a belt off the track, that's your problem.
\015\012
\015\012Here's a video you can watch for free on Bissell's website that tells how to replace a belt. I'm sure the belts can be ordered online somewhere or found at some Bissell dealers or repair shops. Note, again, the two belts are different. If only one is broken, be sure to order the correct one.
\015\012http://cache.vendaria.com/vpop/VpopV6.html?ct=13&ctname=CT630X556D630X390&fw=630&fh=556&logo=49&fv=10&ap=vnd_bissell_change_belt_proheat_2x&purl=MAIN_bissell_change_belt_proheat_2x&iid=sbpgzLIuvIlJlJquLvumgwqKqvIqvv&bg=ffffff&nm=BZOpener&curl=&err=0&title=Bissell&tp
\015\012
\015\012If the belts are intact and in the right place, does the metal cog wheel behind the roller brush right turn when the Bissell is on and the handle is dropped? If not, then the motor that turns that cog wheel must be burned out.
\015\012
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brushes wont turn and wont spray water - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Brushes won't turn and vacuum will not pick up sprayed cleaner


There's a Capt. Obvious fix to check before you go any farther. Like many vacuum cleaners, the brushes on the Bissell carpet cleaners, by design, only spin when the handle is not locked in the upright position, so be sure to plug it in, turn it on, ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.


... Kirby Ultimate G Bagged Upright Vacuum

My ultimateg diamond edition vacuum cleaner is not picking up stuff from the carpet. The brush is turning but it is not doing what it is supposed to.


HELLO, make sure that you have correct hight adjustment.. Make sure that your bag is not to full. and take a look at this link:http://www.goodvac. ... Kirby Ultimate G Bagged Upright Vacuum

I have a Eureka Altima vacuum cleaner that doesn't pick up very well. The suction seems fine but the brush roller doesn't seem to pick up from the top of the carpet. When you lower the height of the vacuum the belt rubs and smells horribly. How can I get the vacuum to pick up better?


That means that you need to replace the belt. Here is the belt you need to replace and the manual which has instructions:Eureka Altima ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My brushes do not turn on my power glide pet vacuum cleaner after I accidentally sucked up the hem of a curtain. I switched off the machine then removed the hem. Now when the vaccuum cleaner is turned


... Electrolux Vacuums

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a


Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Kenmore vacuum- no suction, brush wont turn


Sounds to me like you have a plugged vacuum. Check all the way through. ... Kenmore 22812 Bagged Canister Vacuum

Kenmore vacuum - no suction, brush wont turn


Sounds like the vacuum is clogged and putting too much stain on the agitator, so I would clean out the entire passage way for the vacuum and replace the agitator belt, you must clean out all the hoses it is clogged somewhere ... Kenmore Vacuums

The brush won't spin on my Hyla Vacuum Cleaner. The vacuum does turn on. Am I missing a small connection?


... Vacuums

Windtunnel dual v vacuum cleaner brushes do not rotate when the vacuum cleaner is turned on


When you turn this model on, the only way to have the brushes turn is to move the brush control switch to on and then tilt the handle back. if all of this is ok but they do ot spin then check to see if you can turn them by hand with the machine off a ... Vacuums

Vacuum cleaner when we turn the unit on the spinner brush does not turn the belt is still on the brush but how do you get to the other end.


Go to thehooverstore online. here you'll find an exploded diagram of your machine and how the belt is installed. ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.


Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.


... Kenmore Progressive Direct Drive 30912 Vacuum

Homewell vacuum cleaner, bagless Model SKU3358 won't pick up via the floor brush. Seems to have plenty of suction in the hose. I have cleaner filters & checked there are no blockages.


... Vacuums

The vacuum cleaner does not pick up anything from carpet. It does not even pick up pieces of thread laying on carpet. On tile floors it blows dirt away instead of picking it up. I've tried all the settings on the brush and nothing works. It has done this since new


Sounds like there is a clog..\015\012\015\012Usually its in the hose - look closely.. Stretch the hose out straight and look in there good..\015\012\015\012Or a clog could be in the vac close to where the hose conects to the v ... Hoover U5269910 Bagless Upright Vacuum

Wont spray the cleaner n water out - Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum


Check the dial setting. - presoak, off, cleaner, rinse\015\012is cleaner bottle correctly inserted?\015\012is clean water resevoir empty? \015\012is dirty water resevoir full? \015\012these items will prohibit the water/cleane ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have an eureka power plus vacuum floor cleaner and i have no way of opening the botton to the brush to change my belt for the brush since the brush will not turn.


Look for two screws at the edge of the brush housing. You may see these ones on top. They will be black and recessed ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My model 4870 Eureka type K Vacuum Cleaner won't turn back on after it started smoking. I turned it off, checked the belt and filters, and they seemed to be fine. The brush will turn so I don't think the motor is seized up. where do I go from here? Thanks for you help, David Andrews


... Eureka Smartvac 4870 Bagged Upright Vacuum

I have had my Bissell Healthy Home for just over a year. I use it once or twice a week on five area rugs and two small bedrooms with wall to wall carpet. Just recently, the motor started to sound extremely loud and it smells like it's burning. The vacuum still picks up everything and all the brushes are turning. Advice? I really like this vacuum and would really like to fix it rather than replace it!


Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problem and the hose is clogged...Bissell Bagless Upright Vacuum no ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

Vacuum brush roller wont turn - Dirt Devil Featherlite Bagless Vacuum M085845Vacuum


You dont say if you checked if the belt is still whole so my guess is the belt broke(it could've fallen off and not be there at all but you definately need a belt) check that and let us know ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Brush wont turn..Pressed reset still no turn - Vacuums


If the motor runs and the brush doesn't turn, the first and best suspect is the belt. ... Vacuums

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.


Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

My hoover savvy vacuum cleaner brush will not turn but the belt is fine. i was vacuuming and smelled a burned odor and thought the belt, but not. what's wrong


It could be the motor on it`s way out ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1123 seconds