Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

I have a Bissell pro heat water will not disperse from

\015 I have a Bissell 9200 pro heat water will not disperse from bottom only from tools, I have checked for all clogs and stuck a needle in the little eye holes under the brushes to make sure they were not clogged, but still wont put any water out from bottom\015

Answers :

If the red spray pieces are not clogged but the Bissell still will not dispense water, then I would say the next most likely causes of your issue was either no soap in the tank, or a burnt out water pump. But since you can get water through the tools, I don't see how that's possible. I think it's still the sprayers.\015\012\015\012When you say you stuck a needle in the eye holes of the two red spray pieces, did you actually take the two red spray pieces off the hoses to do this? And then after pushing through a needle, did you try blowing through the red spray pieces? If you can't blow air through them, they're still clogged and water won't go through, either.\015\012\015\012Here's how to get the red spray pieces off the Bissell:\015\012\015\012Unplug the Bissell. Remove the water tank pieces from the top of the base. You'll probably reveal two red plastic pieces mounted in the Bissell's base, about .75" x .75". These spray water on your roller brushes when you press the water-and-soap trigger at the top of the Bissell's handle, and tend to clog with mineral deposits. \015\012 \015\012Only work on one sprayer at a time so you can see how it goes back together. \015\012 \015\012As you squeeze the red plastic sides of one red water sprayer, push up on the underside of the sprayer from underneath the bottom unit of the Bissell to release the sprayer from its mount in the base. Clean any lint or debris out of the mount area. Clean any gunk you can off the red water sprayer with an old toothbrush. \015\012 \015\012Now you need to remove one water sprayer from the hose. You need a pair of pliers. Use the pliers to squeeze the brass colored clip that is keeping the red water sprayed mounted to the end of the small hose there. Move the clip up the hose so it compresses the spring and is no longer on the red plastic water sprayer. (See GOTCHA about the spring, below.)\015\012 \015\012With the clip released, now you can twist and pull the red water sprayer out of the end of the hose. You'll need a little hand strength to do this. Just be careful not to break the water sprayer by using a tool. They're not particularly delicate, but breaking one would render your Bissell useless until it was replaced, so use a little care. \015\012 \015\012When you've removed a red water sprayer from the hose, put the end of the red water sprayer that was inside the hose in your mouth and seal your lips around it, and try blowing through it. If you can't blow air through it, it's clogged. Open up a paper clip and push it back-and-forth through the small hole in the hose end of the water sprayer back towards its middle. You'll probably push out a line of white mineral deposits. Clean them off the water sprayer with the old toothbrush, and try blowing through the water sprayer again. If air passes through clearly, you've fixed it. Push the water sprayer back on the end of the hose. Use the pliers to reposition the brass clip on the end of the hose over the water sprayer. Click the red water sprayer back into position in the base of the Bissell.\015\012 \015\012Now do the same for the other red water sprayer.\015\012 \015\012The GOTCHA: Once when I pulled one water sprayer off, the hose advanced up under the spring and I couldn't reattach the red water sprayer, because it couldn't reach the end of the hose. It?s best to use the brass clip or some other means (rubber band, tape, another clip) to keep the hose from crawling up inside the spring after you pull the red water sprayer off the hose. If the hose gets up under the spring anyway, despite your best efforts, fix this by removing the six screws on top of the Bissell base (this is the surface the water tank mounts on top of), and pry it up. Pull out the hose, reattach the red water sprayers on the hose, position the hose *very carefully* inside the base (there are mounts under there they need to fit into, so you don't break anything), push the red water sprayers through the mount holes and mount them, and then reattach the screws to the base.\015\012 \015\012You might want to prime the pumps. Sometimes an air pocket inside the machine (even a new one) keeps water from flowing, until you reprime the Bissell's internal pumps. To prime the pumps the easy way, turn it on, then press, hold, and release the water-and-soap trigger a few times, waiting a few seconds each time. \015\012\015\012Still nothing? Prime it the slightly harder way. Separate the two water tank pieces. Only have the base tank filled and mounted on the Bissell without the piece that sits atop the tank. Turn it on. Kneeling on the floor in front of the Bissell, reach up and press the soap and water trigger at the top of the Bissell's handle and hold it in as if you wanted water to go through. On top of the water tank is a plastic grommet hole about 1 inch in diameter, through which you pour water to fill the tank. Seal that hole with the flat of your hand. You'll feel just a bit of suction. Lift your hand up and down a few times, a few seconds apart. Release the trigger and repeat a few times. \015\012\015\012 As you probably have learned the hard way, as I did, it's VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Thoroughly rinse out and empty both water tank pieces. Unscrew the three clear plastic pieces, one in front, two on the sides, that surround the brushes, and rinse them thoroughly in water. Clean off the brushes and all the lint and gunk around and above the brushes. (A water spray bottle and toothbrush are helpful here.) Tip the machine and get all the water out of the hole in the base. Release the red clip springs on the red water sprayers and blow on them. Doing this will slow the failure of the Bissell. It's a great little machine for the money, but it does have a learning curve and needs more pampering than a vacuum cleaner, doesn't it?? \015\012 \015\012Good luck!
Absolutely the right answer for me. Couldn't get it to work no matter what troubleshooting Bissell suggested. Took apart the sprayers as above suggested and it works as good as it did the day I bought it. Thanks.
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bissell pro heat water will not disperse from


If the red spray pieces are not clogged but the Bissell still will not dispense water, then I would say the next most likely causes of your issue was either no soap in the tank, or a burnt out water pump. But since you can get water through the tool ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hello.....my Bissell pro heat pro tech does not disperse the water....would you know why


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have a bissell pro heat water wont come out


The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the way to ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Water will not come out of my bissell pro heat clearview


It's probably the heater block check this video out how to fix ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell pro heat not spraying water - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My bissell pro heat 2x does not **** up the water from either the upholstery cleaner or carpet cleaner. Any thoughts as to why? The water and heat functions work it just does not pick up


First check the motor duct gasket. The motor duct gasket is visible once the tank is removed. It is located underneath the handle on the top of the base of the machine. It has a black rubber coating around it. If there is no suction there please let ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

Bissell pro heat steam carpet cleaner, not releasing water.


That means that you need to replace the pump belt. Here is the belt you \012need and a manual you can view:\012\012Bissell 7901 Belt and ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a bissell pro heat water wont come out


The pump may spin but the vanes inside could be broken or worn enough that they are unable to push water through the pump system. I am repairing a Bissell Model 8920 Pro-Heat 2X that has this very same problem.\015\012\015\012I tested all ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How much soap and how much water do I put in the Bissell pro heat?


You are supposed to buy the Bissell soap. On the bottle depending which cleaner you need. The directions are on the bottle. Please do not use house hold cleaners because you can cause serious damage to the vacuum.\015\012Go here, this pg. shows ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell 2x pro-heat sprays water continuously.


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a bissell pro heat model 7901-B that has power but no water circulation. I was told that the previous owner used it without water and that she couldn't get it the power on. I bought it off of her and cleaned it out and now the power works, but there is no water circulation. The brushes run and heater works, just can't seem to get it to circulate water. Thankyou for your time, Don


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My Bissell Pro Heat Select 2X does not pull up the dirt from the carpet into the water. The water just slowly disappears. The first time I used it the water got really dirty. The very next time I used it it worked differently and the water just disappeared until it was all gone. I've only used it a couple times and I don't see where it is working. Has anyone else had this problem?


Inside the plastic suction lid is a little red plastic filter that has to be cleaned out every time you use it because it sounds like your vaccum is not picking up all the hair and debri before you clean the carpet causing the water to be injected in ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell Pro Heat 2X steam cleaner is not releasing the water


Have you tried cleaning out the small filterfrom the reserve tank? Also, check the tank/resevoir valve is operating properly, when you take it out to fill try to make water release from tank. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Bissell pro heat - belts are ok. water will not


Remove the handle, disassemble the lower section of the top to get to the heater. Make sure the unit is unplugged! Use miniature bottle brushes like the painters use to clean paint sprayers (I purchased mine from Harbor Freight for about $4) and clea ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell pro heat will not extract water from the carpet


Try checking the top section of the machine (where the dial is located to switch it from floor to tool) and there is a little red plastic piece about 1 inch square on the inside of it. This is a lint filter that has a little door on it. Open the do ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell Pro Heat 2X will not release water or


Its probably a solenoid that controls the flow to the floor, take it to a bissell repair center, because its not an easy fix. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

My Bissell Pro Heat Pet will spray water but not pick it up when cleaning the carpet. Is there anything I can do to fix it? The furniture attachment hose picks up water well. It seems like it could be a bit more powerful of a draw on water. I don't know it that has something to do with why the floor cleaning sucktion doesn't work. Thank you for your time. Jenn


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bissell Vacuums

My bissell pro heat does not **** up the dirty water anymore at least the dirty water tank does not fill with dirty water


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell pro heat 2X has stopped dispensing water from the tank, the suction is working and it seems to be dispensing the detergent, so it is not rinsing or washing with water. I have cheaked to see if there is a blockage but that doesn't seem to be the problem...please help


I have a Proheat 2X and had the same problem. I tried the Water Rinse setting and found water came out and was suctioned properly, but on the Light Clean, Normal Clean, and Heavy Traffic settings, the unit failed to do anything. Problem may be with l ... Vacuums

My Pro heat 2x by Bissell does not put out or **** up water Brand is Bissell. Model is 8920 12 amp


Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for de ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have the Bissell heat pro 2x 8920 and the water doesn't come out. The soap just mixes with water tank and the carpet stays dry


Check to ensure there is liquid in the water tank and the formula bottle.\015\012\015\012Note: This machine will spray with liquid in the Water tank only if the machine is set to the Water Rinse setting. On any other setting, you need to ... Bissell 8920 ProHeat 2XTM Upright Vacuum

The water in my bissel pro 2X heat will not spray water


I have a proheat bissell and i cant get it to spray from floor cleaner or upholstery took the spinner cap off and the 2 hoses that you can see where the belt is took them off blew in them and poured water into them...That didnt seem to work can anyon ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissel pro heat 2x wont spray any water - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


I had the exact same problem with my ProHeat 2. It would spray only through the hose attachment but not on the floor. Cleaning of the spray endings on the floor unit fixed my problem. Either soap deposits or dirt was clogging the spray endings. Here ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0607 seconds