Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

I used my new proheat 2x steam cleaner the first

\015 I used my new bissell proheat 2x steam cleaner the first time without any problems. This time I cannot get the water tank to sit on the base of the steam cleaner. What am I doing wrong? Am I missing a part at the bottom that connects the two? ..\015

Answers :

You may have mislaid a piece when you took your Bissell apart to clean it after using it the first time.
\015\012
\015\012I experimented with mine to try and reproduce your issue. On the bottom of the water tank, there are two pieces that can be removed from it. One of them looks like a black plug at one end, with a red rubber flange piece on the other end. If you push your finger inside the red rubber piece, you can feel a spring move up and down. This is the first piece you place on the bottom of the water tank. I suspect you have this piece, because if you didn't, water would gush out of the water tank as soon as you turned it over after filling it.
\015\012
\015\012The other piece, which is the one I think you may have have mislaid, is a larger black, plastic ring with screw threads. This piece goes over the top of the first plug piece, screws onto the water tank, and holds the plug in place. The words "RECLOSE TIGHTLY" appear on mine. If this piece is missing, the water tank does not sit flat on the base of the Bissell, but kind of flops around, out-of-place, and the unit will not dispense water properly, though it may leak it.
\015\012
\015\012If ithat piece is gone, it should be possible to reorder it. Start here:
\015\012http://www.bissell.com/Customer_Service.aspx
\015\012
\015\012If that's not the problem, if you have all the water tank pieces, I wonder if perhaps you unscrewed one black screw to remove the clear front plastic piece from the base of the unit-- the piece through which water is drawn up off the carpet-- to clean it, and didn't get it back into place properly. Make sure the two hooks at the bottom of this piece are inserted, one per side, into the clear plastic side pieces at the bottom. If the hooks are not secured properly, before trying to reinsert them, unscrew the black plastic screw so you don't break the tab. It's easy to miss getting these one of those hooks back in right, but it's important to do that before trying to screw the clear front plastic piece into place.
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I used my new proheat 2x steam cleaner the first


You may have mislaid a piece when you took your Bissell apart to clean it after using it the first time.\015\012\015\012I experimented with mine to try and reproduce your issue. On the bottom of the water tank, there are two pieces that ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet - HELP!!!! We're read and reread the manual and contacted customer service and received no help.


First things first. It's only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected und ... Vacuums

Model 79011 ProHeat - First the water and cleaning solution wouldn't come out without pressing the trigger several times. Now the trigger doesIs there a spring on it inside the handle or do I just need to order new trigger. I have only used the cleaner 3 times.


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My first proheat lasted four years so I bought a new one. After I used my Pro Heat for only the fourth time my first issue occured, the gear on the pump that runs the brushes came off, so I had the one from my old proheat, I just changed the gear spindle that is screwed to the pump and fixed that problem but now it will not pump water. That is why I bought a new proheat, I could not get the old one to pump even after a new pump and made sure all lines were not cloged.


Is your new machine a 2X or like the old style proheat? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a new Hoover Dual V steam vac that I bought from a neighbor who only used it once. I have only used it once since then and it worked great. This time, because I am pregnant, I bought some non-toxic cleaner that was much thicker than the very watery Hoover soap. This vac has a wash option and a rinse option. The rinse option works (sprays and sucks properly), but the wash cycle doesn't at all-neither soap nor water comes out. Nothing comes out, but it still sucks. I took everything o


There's a powerful electric motor attached to a fan that sucks in air.Did you checked and cleaned that motor.If the dirt is got stuck up ion the motor then the motor will not spin as per its regular speed.For rinsing the motor spin on one cycl ... Vacuums

Hi I own a Bissell Proheat Powersteamer pro-tech with a turbobrush. I have been using "bissell multi-allergen removal formula for carpets and upholstery." I ran out of that last night. Today I went to walmart looking for more. Everything I found said "2x Ultra Concentrated Bissell multi-allergen." I'm confused on where to add the cleaner. I have a water tank and a separate soap tank. The instructions on this new cleaner bottle say to add 4 capfuls for the formula tank and dilute with hot tap wat


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have an euro-pro steam cleaner model # sc505 that is about 2 years old. It has only been used a limited number of times, about 3 or 4 times. It now has a tightly sealed safety cap on it and it will not release allowing me to add water to the steamer to use it now. Any tips on fixing it? I'd love to have a products guide to items that are available for compatiability with our sharkie. We constantly see new items available and wonder will that product work with ours?? Thanks!


... Euro-Pro Shark SC-505 Handheld Steam Vacuum

I have a Bissell Steam Cleaner that is not sucking up the water when cleaning. I used a full container of water and when it was empty I emptied out the water, only to find very little dirty water in it. I noticed the window, as i used it, seemed like it wasnt sucking up the water. I took the plastic cover off to clean it (it didnt look very dirty in the first place), an i noticed that the grey plastic flap was on but not moving up or down. I thought there may be dirt in it that prevented it from


... Bissell Vacuums

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there's a little thingy that should be spinning or turning..... When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI - I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn't wet. Any tips? The manual doesn't help.


You need to replace the pump belt. Here is the belt you need:Bissell ProHeat Belt ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

New morphy richards vacuum cleaner 73288 belt went first time of use. replaced it and now brushes still do not go round hard to push


... Morphy Richards Vacuums

I don't know how to use it at all need help - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


You can download a user manual from the Bissell website. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha


I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell proheat 2X, model 8960. The shampoo tank does not seem to work, all I get is the water when cleaning. Also the first time I used my shampoer one of the belts broke. This is the 2nd cleaner I have bought. Was hoping this one would last longer. Cleaning this model is a real pain, surely there is a better why.


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

This is new and using it for the first time. i have read the instructions and it still not heating up and still no steam-what am i doing wrong. as im pumping it. it just keeps soaking my floor


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Need instructions onj how to use a Bissell proheat steam cleaner


Most of the manuals can be downloaded at the Bissell.com web site ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I purchased the bissell proheat 2x steam cleaner approximately 2 years ago.... used it approximately 5 times... now the sprayer will not spray.... i have checked the spray nozzles and there is not an interference... what do i need to do... my mom bought one the same time and it too is doing the same.


Too much different washing liquid mixing procreant bulkhead in the water pipe hose\015\012\015\012try use clean water cleaning\015\012\015\012\015\012 ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a new STEAM VAC Dual V All Terrain Carpet and Hardwood Cleaner. I have used it once and it worked well. Now, the second time, I have no water return. I checked the tank location, the brushes are moving slowly (but the plastic surrounding around the brushes moves as well ??) Water is coming out. There is hot air blowing out, but there is no air suction. What is wrong? Ursula Litzcke


Hello litzcke.\015\012There are lots of people facing this problem as well as other problems with this machine. As there are lots of faulty with this product; would not **** up water/air/shampoo, will not brush and lots more. If it is under war ... Vacuums

It's my first time using my pro heat steam cleaner. The water or detergent seems to not be putting out at all?


Colgged or damaged pump, you use a proper detergent?read the instructions. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How do I use it? We lost the instructions - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


I would go to the bissell web page and down load the instructions. It is too complicated to explain on here. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Brushes We have A Proheat Select X2. Brand new, using for the first time, heater works, liquid dispenser works, Power brushes on machine and on extension attachment do not turn. Any thoughts? Thanks gigi2244


If the floor brushes don't turn, there is a motor for that and it maybe bad, On the attchment, vacuum is what turns those brushes, On the tank there is a knob to turn for the floor or hose, is it turned for the right application? other then that, y ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bisell proheat steam cleaner Metal sprocket feel off pump and will not go back on. Do I have to buy a new pump system?


... Bissell Vacuums

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1


Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0798 seconds