Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

Machine does not spray fluid on rug when trigger is depressed. have tried repriming pump per trouble shooting manual. No help.


Answers :

Hi
\015\012Either soap deposits or dirt was clogging the spray endings. Here is what to do to clean up the spray endings:

1. Remove the water container from the bottom unit
2. Look up for two red plastic endings on the bottom unit
3. Using your fingers to clip sides of an ending, carefully remove it from its slot
4. Using pliers, release the clamp from plastic ending and remove the red plastic ending from the hose
5. Clean the ending
6. Put the ending back on the hose, slide clamp back on the ending
7. Insert the ending back in its slot
8. Repeat 3-7 for the other ending.
\015\012OR
\015\012I have had the same problem on and off since I bought this cleaner. take it apart and find out the solution. I thought the solution was gravity feed but found out there are two small pumps, one for the bladder solution and the other for the chemical feed. I certainly could have designed a much simplier machine, but what bissell has done is used the vaccuum pressure to pull the solution into the pump in order to prime it. If for many reasons there isn't enough vaccuum pressure the pumps will not prime. What I did was put the tank on the machine without the top cover. I turned the machine on and reached up and held the trigger open with my other hand I put my palm over the vaccuum port for about 3 seconds and then allowed the air to flow back into the motor. I repeated this about 5 times until the pump primed I put the top lid on and locked it into place put it back onto the machine and it worked perfectly.
\015\012
\015\012HOPE THIS WILL WORK
\015\012REGARDS
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Machine does not spray fluid on rug when trigger is depressed. have tried repriming pump per trouble shooting manual. No help.


Hi\015\012Either soap deposits or dirt was clogging the spray endings. Here is what to do to clean up the spray endings:1. Remove the water container from the bottom unit2. Look up for two red plastic endings on the bottom uni ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a bissell power steamer That is not spraying soap, only water. I have checked all the filters and belts that I know of I also tried to reprime the pump as indicated in the trouble shooting section. Is there anything else I can try? Thanks


If it spraying water, then the pump is ok. The valve at the bottom of the soap bottle may be bad. Also when you turn the smart mix vavle, does it turn easily or hard, if hard, try spraying some furniture polish around the knob and turn it to work i ... Vacuums

We just took our dirt devil Platinum Force Carpet Shampooer Model CE7900 out of the box - first time used. It puts soap and water down fine, but we can't get any dirty water picked up. None of the trouble shooting suggestions in the manual apply. HELP! (We had only the power on when trying to pick up the dirty water.)


... Dirt Devil Easy Steamer Upright Wet/Dry Vacuum

Either of my bissell porheat turbo 2x or my bissell pro heat don't have suction i would like to try and trouble shoot if i could due to the fact i am having difficulty finding a small machine repair center in my area could you possible help me or send a link which could help me find solution these machines are not more then a year and a half old if that thanks for your time and help warmest regards rebekah majors


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Won't spray Checked everything four times and nothing is clogged. It sprays once in a while but only for a few seconds. I'm about to toss it and buy a hoover unless someone can help me trouble shoot now.


Ensure you have water in tank and solution (or water in solution tank). When you start the vacuum up, the pump starts to prime itself. If you have air in the system, it takes a little longer to prime. Allow the vacuum to run for 1 minute before attem ... Bissell 9200 Upright Vacuum

I got a vacumn from a friend who ungraded and though i used at her home when i got it home it would not turn on when plugged in and i check everything and no use. my friend lost her manual. im in my 60's and on a disability fixed income so cant afford to take to repair but got lots of men at church who would help if they know how to trouble shoot it. and would really appreciate any help. thank you , ann


Hi\015\012In the UK we have similar machines but they are made by Vax. If you can't source the correct user manual from Hoover.com consider the following - it is a free download.\015\012\015\012http://www.vax.co.uk/downloads/pdf/vzl-60156016_v2 ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

I have a necchi sewing machine model 4795 and I am having trouble trying to do zigzag stitch for applique. Can you please help me with the settings on the machine. I have tried to use manual, but I still cannot get it to stitch correctly. Thank you.


... Vacuums

My brand new Hoover F914-900 steam vac spin scrub will not release the water. I have tried all of the trouble shooting advise in the owner's manual.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My bissell proheat will not put water out and I can't find my manual. Hoping to find a trouble shooting section. Help???


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell pro heat sprays water and solutioon for 15 seconds than stops from haqndle as well. I have a new pump and everything has been reinstalled as per manual. Whyat could be casuing thi stoppae? Thanks


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

The brush just stopped...tried trouble shooting in users guide but no luck. It's only six months old. Help!


Is the belt broke if so replace? ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I have a modelF5914-900 steamvac cleaner.serial #0704 0011 4711 I cleaned the carpets in my house and then started to do the stairs with the stair attachment. I got down to the last four stairs and the solution would no longer come out. I checked the tank and hose connection and tried priming the pump per the instruction manual. nothing worked. Could you make a suggestion as to what the problem could be? Thank You


Check fuses goin to the pump, is the pump working? if so you may have an air pocket or a air leak in the intake. ... Vacuums

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it's prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.


Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell ProHeat Pro-Clean upright cleaner won't spray either water or solution onto the floor, however it does spray when using the attachments on the hose. The belt is fine, I've actually tried all of the troubleshooting steps indicated in the User Manual. I'm not even certain where it is supposed to be spraying out from! Any ideas where/what to check for?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a Bissell Model 7920 that does not spray through the floor or the attachment. I have disassembled the unit and the only area that water does not pass through is the top of the pump through the pump. How can I unclog or trouble shot a bad pump?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet - HELP!!!! We're read and reread the manual and contacted customer service and received no help.


First things first. It's only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected und ... Vacuums

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

I have a Polti Vaporetto Lecoaspira 710. I have filled the tank and set the machine up as usual. When I turn it on the boiler pump runs continuously for a minute or so and then the 'beep' begins and the machine shows that the boiler is empty. Obviously the water is not getting through. We don't live in a hard water area so it shouldn't be 'limed -up'. The manual says to leave it to cool down and then try again. That had no effect. The only answer that Polti 'Service' could give me was to try 'G


... Polti Eco Pro 3000 Canister Steam Vacuum

HA-871? I'm not sure if anyone can help with this, but I've got a **** Smith brand HA-871 alarm system which I haven't used in years. When trying to get it working, not only have I forgotten the code but I can't remember how to enter it (as in, 4 digits and a #, or just the 4 digits, or something else...?). As I am able to get into the alarm box with the key, does anyone know how to reset it and enter the code? I can't find the manual either. Thanks to anyone able to help with this!


Incase you are still interested you set the code with the four jumpers inside the unit.\015\0121st digit is the brown wire\015\0122nd digit is red wire\015\0123rd digit is orange\015\0124th digit is yellow ... Vacuums

We have the water hooked up at the back of machine. there is a spout for the water to come in and fill the ice tray.but is does not. If we turn the water on it fills up the space under the ice basket. I keep getting red light and then the two smal llight one ice and one water come on. We can hear the motor trying to fill the ice try and then lights come on. Please help me this so I can use this product. It did not come with a manual.


The water inlet valve on the back of unit opens when the ice maker needs water. If the valve doesn't seal good because of sediment or wear it will continue to drip and when the water reaches the ice maker supply tube it will freeze blocking the fill ... Vacuums

Help!! Hi, I recently bought the dirt devil spot scrubber at a rummage sale, it came with no manual, I have tried to down load the manual and cannot, if someone could just tell me how to use it, if solution needs to be diluted, ect... I would appreciate it. Thank you!


Look up instruction manual at\015\012\015\012http://www.dirtdevil.com/CustomerService/Manuals/DirtDevilManual.aspx?ManID=325fa4dd-0a38-48aa-b0b0-516143a0875a ... Dirt Devil SE2800 Spot Scrubber Handheld Wet/Dry Vacuum

We have a bissell 12amp pro heat when we try to use it it will not spray out the cleaner this is the second time we tryed this help


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Vacuums

I have a craftsman garage door opener remote control model TX2028 139.18191. The remote stopped opening or closing the garage door. I replaced the battery and tried to re-program it through the LEARN button as per the manual of the Garage 1/2 HP opener. The process has failed after several trials and the remote is still not working. Is there anything else that I can try or should I get a new remote. Thank you


... Vacuums

I have a Bissell Proheat 2X Carpet/Upholstery cleaner and I can't get the soap and water to come out of the attatchment. The vacuum part is working, but the spray isn't. I can see the fluid is trying to go up the tube but won't spray. Help. Peggy


Hello, I have a Bissell "Little Green" cleaning machine that acted like yours. I found several clogs in the fluid system. The power for the fluid in my unit is provided by a small AC motor independent from the vacuum motor attached t ... Vacuums

Hi all, I have a Janome 234D overlocker and when I try to sew with it, it misses stitches. What could be causing this problem and how do I fix it? I tried rethreading,checked the tension and stitch length dials on the side and I dont have a manual for any instructions, help is desperately needed, regards Wendy


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0933 seconds