Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

I have a Bissell Upright Proheat 2x and the dual power brushes wont rotate. I went to replace the drive belt and noticed the drive shaft does not turn when power is turned on. What shall I check next?

Answers :

Is there a light that comes on when you "turn the power on." If there is no light, and the unit is plugged in, how do you know there is current going to the motor? Sounds like there might be a break in the cord. Examine the cord near the plug end to see if one of the internal wires is broken. If you cannot tell, then you need to try taking the unit apart where the cord enters the unit and testing continuity with a meter.
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bissell Upright Proheat 2x and the dual power brushes wont rotate. I went to replace the drive belt and noticed the drive shaft does not turn when power is turned on. What shall I check next?

Is there a light that comes on when you "turn the power on." If there is no light, and the unit is plugged in, how do you know there is current going to the motor? Sounds like there might be a break in the cord. Examine the cord near the plug end ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it

The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

My Discovery 4210 Roomba will run normally for about 20 minutes on a smooth, wooden floor. It then begins the following sequence: run forward a few inches, turn in a tight counter-clockwise circle a few revolutions, stop, power off a few seconds, power up, repeat cycle from forward run. The sequence can be repeated seemingly endlessly if I don't turn off the power manually. I've replaced the motor, and led revolution sensor system on the left drive wheel. I've blown the dust out of everywhere. A

This robot vacuum has a electronic micro processor that controls the unit and tells it how to operate and where to go based on programmed parameters. It's quite a technical marvel. I have dropped a link here for contacting the company tech support li ... iRobot Roomba 560 Robotic Vacuum

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T

... Rainbow E series Canister Wet/Dry Vacuum

Both drive and slave belts are intact and tight on the Bissell ProHeat 2x. The brushes will not turn. When last turned on, there was a loud snap noise and something is broken in the power head drive train. Can we repair this or is there a service center near the Hastings, MI area? We need this fixed ASAP. Thank you.

Sounds likely you should take it in your drive gears might have a problem ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on

... Miele Blue Moon Bagged Canister Vacuum

I have a Kenmore Progressive upright model 216-37100800. It is only around 1.5 years old. My wife said that one day after she plugged it and turned it on, it whirred up but then shut off. Since then it will not start. I have noticed that right after I plug it in, if I try to turn it on, the first yellow light in the series of dirt sensor lights turns on then shuts off. After that the light will not light up on pressing the power button, unless I unplug it and plug it back in again. I have seen o

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hi. I borrowed my friend's Hoover VC340 to clean my house. I was vacuuming when i noticed the cannister was full, so I turned the vacuum off, pulled out the barrell, and followed the instructions on the barrell to empty it. I put it back into the machine, but it wont turn back on. I tried different power outlets, but to no avail. any thoughts?

... Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i

At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I have a Bissell proheat 9200 T. The brushes engage when the handle is lowered. However they only turn for about 20 seconds then stop. If you turn the power off then on they run about 20 seconds again. It is driving me crazy!

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9200 Upright Vacuum

After using the vacuum I could not turn it off with the remote and then after a few minutes it stopped on its own and then would not turn on again. The next day again no power at all.

... Nilfisk GM 80 Bagged Canister Vacuum

Power problem I have my Progressive with direct drive for 3 weeks. I was using it today then stopped. When I went to turn it on again nothing no power at all

With out checking it, it is hard to say, I think there is a reset, did you push it? But you do have a years warranty on this, that it into Sears for repair. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?

I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum

I unscrewed the roller brush protective cover and removed the brush to clean it. Now the roller won't turn because the drive shaft is not turning. Is there a reset button or something?

I looked at the pictorial of this vacuum at this URL:\015\012http://middleeasten.bissell.com/images/UserGuides/3750.pdf\015\012\015\012This shows the belt to slide on the motor drive pulley and also on the brush. If the brush is bound up on th ... Bissell 3750 Lift Off Bagless Upright Vacuum

Electrolux Renaissance power nozzle turning on and off, brass pins hot

The deal with the Renny is that it runs off of circuit boards. Usually the problem of the main motor shutting on and off is caused by one of the Triac boards located inside the canister. Another problem could be the thermostat wire located on the i ... Electrolux Guardian Bagged Canister Vacuum

Bissell Proheat 2x Series 8920 - Brush Belt Metal Shaft Sprocket won't turn

Most likely the brush motor is bad and not turning, part #2036757, would sell for around $23. To get to it, start taking out screws on the top cover, that motor is under the that top access cover. ... Bissell 8910 ProHeat Clear View Upright Vacuum

It won't turn on. I have partially disassembled it and have continuity between the power cord (wide blade) and one of the connectors where the switch assembly snaps in. Also, switch is working fine. There is continuity across it, then no continuity across its connectors when the switch is pressed. Not sure what to try next.

\015\012Please provide the make and model. Thanks. ... Vacuums

On my Hoover 6660-900 bagless upright self propelled wind tunnel vacuum when I replaced the cable which works the power drive, there is a spring next to the control arm which I cannot quite figure ou

... Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb

Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

Took my Miele Solaris canister vac in for repair as it wouldn't turn on. The repairman said to come back the next day for the estimate. I called and he said I needed a new cord reel and it would be $189. I drove to his shop and said I would wait to do it later, that I wasn't ready to spend that much. When I came home, it started right up but has no power and doesn't sound right, the noise of the motor is real soft, not as loud as before. I have this terrible feeling that when we decided not to

When you say 'has no power' do you mean , no suction? He may have left the suction hose of the motor and that's why it sounds different. I would call him back and request that he put the machine back to it's original 'state' as it was when you brough ... Vacuums

I noticed the Roomba's brushes were not sweeping, or turning so they could sweep. There was a new sound coming from the machine, the sound of grinding nylon! Upon inspection, I determined the problem to be a heat melted gear support hole. The hole was no longer round but oblong. You could see a ridge of plastic around this hole. So melting I believe was the culprit. The gear that uses that hole was then able to tilt to one side, thereby allowing the gear to disengage from the drive train. I

Be sure to keep your brush bearings clean. If they get clogged, the brushes don't turn and the drive sockets can get damaged. ... Vacuums

My Miele capricorn has started making an odd noise. It seems like something is blocking the engine. I've turned if off and on, and reset it and it still have the odd, almost loud barking noise. The power nozzle also does not seem to be working. I've checked the connections. Right before this happened I was using the vacuum. I didn't notice anything out of the ordinary until this.

Greetings,\015\012\015\012This is a major problem. The Miele vacuums motor should never make a loud noise, period. The way the motor is designed, it's quiet and should be quiet for the life of the motor. There are two motors on your ... Vacuums

On turning on different noise then noticed smell of burning then just stopped working and no power since. DC 07 Dyson.

Unfortunately your motor had burnt up..most times this is due to not cleaning or replacing the filters...the filters get dirty and the motor gets no airflow to cool it....very common on dyson vacs ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson 24. I just bought a new Dyson ball 24 and the brush won't turn on, I tried to follow instruction and push the red button to reset it also next to the power button but doesn't do anything. Any suggestion.? Thanks Sam


My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab

(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4497 seconds