Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

No suction power does not get up the dirty water


Answers :

Your suction problem is most likely due to a clogged lint filter. It is located in the top clear plastic section. This is the one with the dial to switch from floor to tool mode. On the underside of this section is a small (1 inch square) red plastic piece with a door on it. Flip open the door and you will probably find that it is all clogged. Clean it out and you should have suction again.
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No suction power does not get up the dirty water


Your suction problem is most likely due to a clogged lint filter. It is located in the top clear plastic section. This is the one with the dial to switch from floor to tool mode. On the underside of this section is a small (1 inch square) red plas ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We just took our dirt devil Platinum Force Carpet Shampooer Model CE7900 out of the box - first time used. It puts soap and water down fine, but we can't get any dirty water picked up. None of the trouble shooting suggestions in the manual apply. HELP! (We had only the power on when trying to pick up the dirty water.)


... Dirt Devil Easy Steamer Upright Wet/Dry Vacuum

My Bissell 9200 is not sucking the water into the dirty water resevoir. 1. The gasket on the clear-view seems fine. 2. The suction power just doesn't seem powerful enough (feeling with my hand). 3. The brushes turn fine and belt is fine (not sure if that even matters for this issue). Any help appreciated. Thanks, - Matt


Disassemble all lines and check to see if all O rings are installed. If cracked missing or stretched out of shape no suction will be provided ... Bissell 9200 Upright Vacuum

The clip that connects the water base to the top of the suction area broke off..where can I get a replacement base (the part where you put the water in and has the bag where you also store the dirty water)? I have a Bissell proheat 2x


Here is the number for Bissell, they can tell you who to contact near you.\015\012Service Center Dept. Phone Number:(800) 457-1509Service Center Dept. Fax Number:(800) 517-9535Hours:M-F 8:0 ... Bissell Vacuums

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

I have a bissell pro heat model 7901-B that has power but no water circulation. I was told that the previous owner used it without water and that she couldn't get it the power on. I bought it off of her and cleaned it out and now the power works, but there is no water circulation. The brushes run and heater works, just can't seem to get it to circulate water. Thankyou for your time, Don


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????


Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

The suction on my Hoover Spin Scrub 50 is suddenly not working. This is the 2nd or 3rd time I've used it and until now it has done a great job. But now it leaves my carpets soaking wet with no hope of drying and no dirty water is being suctioned into the dirty water tank. Help!


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover Agility Steam Vac has no suction for the dirty water


Broken suction hose. ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but that's all t


The spray jet has become clogged from the soap.... just clean it out. same thing happened to my attachment. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

When taking the handle/wand back to use it seems to lose the suction power regardless of what setting I use. Upon several times of standing it back up it seems to engage the suction power correctly is there a button or something that does not always engage to get power? can I fix it


When you say taking handle back I assume you mean the action to start rotation of brushes. Had simular problem and found by removing brush from tube and then cleaning "baked on rubbish" in plastic tube (so you can see clearly through tube) Clean with ... Dyson DC28 Animal Bagless Upright Vacuum

There is no suction and the machine will not pick up any dirty water in the dirty water tank.


... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum

It won't suction the dirty water up to the container. I have ck'd the lid for the dirty water several times. Any other suggestions?


Assure the ring gasket is in place under the hood. A round rubber gasket must be in place on the round tube under the hood where the recovery tank sits to connect the vacuum from the motor to the round tube on the bottom of the tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a CT600 power brush that would not power up. Thinking the motor was bad in it, I replaced it with a new CT700 power brush, I am still experiencing the same problem the power brush itself does not seem to be getting electic power, but the Vacuum unit does come on with suction.


First try connecting the power nozzle directly to the hose. If it works, the problem is due to a broken wire or faulty connection in the wands. At least one wand will need to be replaced.\015\012My guess is it's probably due to a broken or di ... Broan-NuTone VX550 Bagged Central System Vacuum

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl


There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 - On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 - not


Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Bissel proheat 7901 carpet cleaner and it is not sucking the water up. Normally when I clean the water gets sucked back up and I have to empty the dirty tank. Now no water is in the tank when I am done cleaning. Please help I cannot afford to take it to the shop.


I'm not sure if this will help but I had the same problem and was about ready to pull my hair out. I ended up taking the fill tank off and if you look inside where the red overflow flap is you will find a small screened opening. I found that mine w ... Vacuums

My kenmore model no 116.22512200 canister vacuum power head has no suction & doesn't pick up even though it shows all the signs that it is getting power. The junior power mate works fine.


... Kenmore Vacuums

Hoover aquamaster recently purchased hoover aquamaster, trying to shampoo carpet, can't get water to come down tubes, water keeps going into dirty water tank.help!!!!!!!!!!!!!!!


Sounds like you need to attach the air hose\015\012\015\012with reservoir in place you clip on the lid with tubes attached, one of them goes down to the floor cleaning nozzle, the other tube should be about 20cm long with an end piece, ... Vacuums

I have one central vacuum location that does not receive power. All other locations work. I do get suction but just no power. What should I do first to test power to location.


You need to use a circiut tester (electrician test probe) on the two terminals the hose plugs in to to see if power is present to connect to. The receptacle likely has damage to the power connection from arcing from the hose previously not fully plu ... Hoover Powermax U5242-930 Vacuum

Have a Bissell Proheat2 will not spray water from the carpet power head but sprays from tools setting Does anyone know how to get water to spray or clean out water


I had this problem. It was small pieces of debris that got into the solution lines and clogged all the nozzles. There is a nozzle for the handheld attachments, one on the front of the machine for spraying spots and two nozzles underneath just behind ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Went to get some water for the Bissell Petwash power brush, when I reconnected it, the water is not coming through the house. The vacuum is working, just not the water.


Try this...... take a part the upper half of the machine and\015\012look for the heater.take off one of the hoses and plow in it to see if it is clogged it is take a part and clean out .\015\012what happens is it gets clogged with soap and wate ... Vacuums

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks


This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have one central vacuum location that does not receive power. All other locations work. I do get suction but just no power. What should I do first to test power to location.


Remove the face plate from the wall and test the low voltage wiring behind. Before undoing the screws where the wiring connects, reach inside the inlet and feel the two brass pin connections. There should be spring tension behind each. Underneath the ... Hoover S5604 Central Vacuuming System Power Unit Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0782 seconds