Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?
Cannot pump cleaning fluid cleaner will **** up water. Have taken apart and cleaned out well.
There is a small oumo they go out often not exoensive.
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Cannot pump cleaning fluid cleaner will **** up water. Have taken apart and cleaned out well.
There is a small oumo they go out often not exoensive. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
It will empty the cleaner but will not spray water filter is clean spray heads were taken off & i could blow threw them is it a case of no prime in pump if so should i fill pump i had this thing all apart and i now know evry inch of this matchine when i pull the triger it sometimes will spray for a sec.but thats it i also took the switch out and air goes threw when i press the switch if it is the prime in the pump how can i fill the pump . what hose on the pump will prime i thankx for your advic
The problem is most likely that your pump belt is worn, stretched or broken. Here you can get the belts you need and view the manual:htt ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.
... Bissell 1960-3 QuickSteamer Plus Upright Vacuum
It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu
Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum
The carpet cleaner does not spray cleaner, nor vaccum up excess water. It's been taken apart, cleaned, reassembled, refilled, twice. Have double checked seating of tank, placement of filled cleaner bottle and yes - it's plugged in.
Hi\015\012\015\012 \015\012\015\012The issue may be due to flow system; to troubleshoot the\015\012system follow the instructions--\015\012\015\0121. Remove Smart Mix piston from the main housing and place Smart\015\012M ... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum
My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?
... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
My dyson vacuum cleaner doesn't seem to have the same suction power it used to. I have cleaned out the canister and have taken apart the vacuum head (for cleaning carpets) and it doesn't seem to be blocked but it seems to lose suction by the time it reaches the head. The suction is strong at the end of the hose (where you attach the telescopic attachment with vacuum head) Any ideas? Thanks, Irene
My roomba 560 will not go forward, just keeps tuning to the sides or backwards. Ihave taken it apart and cleaned it very well but that did not help. What can I do?
\015\012Your bump sensors are malfunctioning. The best thing to do is order a repair kit... I ordered mine from EESolutions.ca and it worked great. I'd recommend them. ... iRobot Roomba 560 Robotic Vacuum
My bissell pro hear steamer will not pump out water or cleaner on the carpet. is it stopped up and how do I take it apart to clean
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
My bissel proheat 2x pet cleaner is not releasing water It will **** up water but it won't come out while pressing the button or on it's own It has been taken apart and cleaned
... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Max Extract cleaner stopped sucking up water! Stopped working within an hour of purchasing it! I've taken the dirty water tank apart, cleaned both filters, and it still will not draw the water out of the carpet.
Try returning it to the place of purchase. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!
Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum
Hoover Jet and Wash 1500w S6254 001. Used once with great difficulty as assembly and use instructions are hard to follow.Now will not work as carpet shampooer at all, although assembly is correct as far as I can see and both motor and pump appear to be working and I am using the recommended cleaning fluid.Hoover website is no use at all in solving the problem.No cleaning fluid is being drawn up from the tank in to the cleaning fluid hose.There is suction from the suction hose so the problem appe
I am having the same prob my uncle got me one i cant find the manual anywhere to set it up the prob i have is where does the handle to make the water go out connect tooo ??? on the main pipe that sucks it back up i have tried every which way but not ... Vacuums
My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there's a little thingy that should be spinning or turning..... When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI - I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn't wet. Any tips? The manual doesn't help.
You need to replace the pump belt. Here is the belt you need:Bissell ProHeat Belt ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Which Kenmore vacuum cleaners are made by Panasonic? Are all of their direct drive machines made by Panasonic? We have a blue Hoover Windtunnel with the dirt sensor. It cleans well, but it is unbelievably noisy. I wondered if something was out of place and the brushes were hitting, but everything looks normal. We bought Kenmore models 36722 and 36724 and love them. I believe they were made by Panasonic. Our Kirby sits in the basement. Much heavier. These are quiet and clean well. I would like an
Some Kenmore vacuums are made by Panasonic, some are made by Hoover or Eureka or even Sebo. I would go to a Panasonic dealer for that kind of machine instead of trying to go by the Kenmore brand. Sears has a hard time with service. A good Vacuum C ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o
Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I am wondering how I can clean the inside of my bissell spotlifter powerbrush hand held cleaner? I want to clean the part where you suction up - it is full of gunk and hair and I can't figure out if it comes apart or not so I can clean it. Can you help?
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=49876&thid=506980\015\012I am wondering how I\015\012Posted by carriespets on Apr 12, 2008\015\012I am wonde ... Bissell SpotLifter 1716 Bagless Handheld Vacuum
I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t
Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums
HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch
... Hoover Vacuums
It clicks as it is going and stops after about 30 seconds. Two beeps. I have tried cleaning brushes and have pretty much taken the whole thing apart, cleaned the motor, the brushes everything. Still doing to same thing, when this has worked before.
It clunks because the gears are damaged. You will need to replace the CHM. If you have the red cleaning head module, chm, replace it with the green chm. ... Roomba Robotic Floor Bagless Vacuum
My Bissell Proheat2 Model 9200 does not spray cleaner. I took all the hoses(tubes) off and cleaned them. They had the dried cleaner in them. Still does not spray. Could it be the pump?
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9200 Upright Vacuum
I have a bissell proheat carpet cleaner model 8910-w 08019c.the machine will not add cleaner or water to the floor.I have cleaned all the filters with it still will not work. I have checked all the fluid levels and reseated the tanks and still can't get it to work. What else can I do?
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Burning smell how do I get the bottom section apart to clean it out- burning smell when i have the spin brushes turned on. Any help would be appreciated cause I love this machine and hubby told me it couldn't be taken apart to be fixed. Thank you.
The bottom doesn't come apart. you have to remove the top cover to get to any components. But if you have a burning smell, then it is probably ther motor and would have to be replaced. Motors cost anywhere from $70 to $90. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
No suction I live in a house with two bernese mountain dogs... very large animals who shed a LOT. I've cleaned the filters, the roller, and gotten as far into the hoses as I can without taking the entire machine apart. It's still not cleaning as well as I know it can... nothing is making it into the debris receptacle. What can I do?
Hi elora,\015\012\015\012I live in a house with three shedding cats. I also have the same vacuum. About twice a year, I have to getinto the area of the vacuum where the motor is. There is a little pring loaded vavle that sometimes gets ... Bissell 3590 CleanView Bagless Upright Vacuum
Cleaning! To clean the cyclonic cone Dyson say to use can-air? that may be ok for computers but not to blow out the dirt and dust from the cone in question. Someone else here suggested to use a real compressor! Well dahhh I knew that! Should I do the blowing in the living room? or may be in the bathroom? Seriously what I need is an assy. drawing to take it apart and washing it Any ideas where I can get one? Thank you John
Hi, we realy love our Dyson, but get frustrated when it gets clogged with pet fur (2 cats and 2 dogs). This takes a little effort but what we ended up doing was taking the vacuum apart into its major components and alternately blowing it out, filter ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum