Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

I have a Bissel steam cleaner and I had to replace the brush belt and I don't have a manual to replace it back on the machine.


Answers :

Here is the manual for your model:

User Guide (PDF)
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bissel steam cleaner and I had to replace the brush belt and I don't have a manual to replace it back on the machine.


Here is the manual for your model:User Guide (PDF) ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine


... Bissell 8910 ProHeat Clear View Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

We replace missing belt for roller brush on our bissell carpet cleaner, its loose and still doesn't rotate. Model # 8910 Looking for manual to fix this problem


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a proheat carpet cleaner model 3 7901. the problem is the brush on the bottom of the machine plus the two end parts and the belt came out. i put everything back but they popped out, they are not staying in place. what am i doing wrong or what do i have to take out to get everything in place correctly?


Hi\015\012\015\0121. You’ll need to follow this procedure to assemble your unit back together.\015\0122. Make sure the foot pedal is in the proper position.\015\0123. The SmartMix should be properly loaded into the main ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike


... Hoover Vacuums

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks


You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?


Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Replace belt and dyson vacuam cleaner, model dc14 I ordered a new belt and brush replacement assembly and we can't seem to understand how to get it apart to change it


If the DC14 has a brush protected aspect i.e. a switch on the front that puts the drive belt off, the drive belt would have to be replaced by a professional repairer as this can't be done at home. \015\012\015\012If the model doesn't have the b ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

We have the pet steam cleaner bissell 12 amp, we tried cleaning off the brush, because the cleaner wasnt sucking up the water sufficently. a screw came out along with the belt roller, and we have no idea how to put the screw or the belt back on.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Hello I can not find my manual for my vax vs19 swift vacuum cleaner and I am having problems with the cleaner not picking up. It is a 1600w machine and is fitted with a hepa filter, my son took it apart and without the manual it is difficult to reassemble not sure if he has put it back together properly.


Check out this site;\015\012\015\012http://www.vax.co.uk/support/vacuum-cleaner-user-guides\015\012\015\012Scroll down to the one that's applicable. ... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No


Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie


Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum

I need instructions on replacing the belt that drives the brushes on a Bissell powersteamer pro deluxe carpet cleaner. Could the broken belt have anything to do with the suction of the cleaner?


Here is a link to the belts you need and a link to the manual:Bissell 1697-7 Manual and Replacement Belts ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1408 seconds